All Products

6850015 X-pid 9500 Multi-Gas Detector, US/CA/AU by Draeger

The selective PID gas measurement device is ideal for users who frequently test for hazardous toxic substances. Benzene, butadiene and other volatile organic compounds (VOCs) are carcinogenic even in the smallest concentrations. Selective measurement is necessary because other gases and vapors are often also present. The gas measurement device allows for short test times and lab-quality results.

Two modes for an efficient measurement strategy

"Seeker" mode is a wide-range measurement for pre-testing and localizing measurement points. It allows continuous, direct-reading measurement of the total concentration of all VOCs present. "Seeker" mode is similar to using a single-PID gas measurement device.

"Analysis" mode allows selective measurement for monitoring specific toxic compounds. Predefined target compounds can be precisely measured in seconds. "Analysis" mode is similar to gas chromatography analyzes conducted in the laboratory.

Up to 90% faster

The Draeger X-pid 9500 requires no preparation and is ready to use after a brief start-up phase. Selective measurement in "Analysis" mode takes only a few seconds. A benzene measurement starts with the push of a button and is completed in only 30 seconds. After another 60 seconds, the device is ready to measure for benzene again. Compared with other detection systems, the Draeger X-pid 9500 saves considerable time and enables further monitoring to be undertaken. Simultaneous measurement of other compounds, like benzene and butadiene, further reduces testing times.

Cost savings

Because no consumables are used to take measurements, operating costs can be reduced. For users with high measurement needs, the Draeger X-pid 9500 quickly pays for itself. For example, it requires no pretubes, also making it easier to use and preventing user errors. On the basis of 200 measurements per year, the Draeger X-pid 9500 is generally more cost-effective than comparable measurement systems.

High selectivity for greater safety

The selective measurement mode "Analysis" relies on technology which separates individual compounds present in mixed gases. This makes it possible to conduct a compound-specific measurement for benzene, even if other VOCs like toluene and xylene are also present in high concentrations. Cross-sensitivities for benzene are reduced to a minimum. This reduces the number of false-positive measurement results and false alarms.

Reliable performance under tough conditions

The influence on measurement results by environmental factors like variable ambient temperature or high humidity are reduced to a minimum. The sensor unit maintains a constant temperature above the ambient air temperature and separates water vapor from the target compounds. This ensures reliable measurements under tough environmental conditions.

Low detection limits

Concentrations of toxic compounds in the air at work sites must not exceed threshold limit values. Mandatory time-weighted averages in the low ppb to ppm range need to be performed for carcinogenic vapors like benzene. The Draeger X-pid 9500 is optimized for measuring in this concentration range and detects benzene starting at 50 ppb.

Intuitive handling with mobile app

The sensor unit is controlled and the measurement data processing is conducted by a mobile app installed on an explosion-proof smartphone (delivery includes both). The large touchscreen and familiar user interface elements are easy to use. This makes the sophisticated technology accessible to a broad group of users. No prior knowledge or extensive training is required.

Lab-quality measurement results

The gas measurement device is based on gas chromatography (GC) and photoionization detection (PID) technologies. These technologies, used widely in laboratories, have a high acceptability due to their excellent analytical performance. The Draeger X-pid 9500 brings these technologies directly to the hazardous area of any production site.

Simple functional test and calibration

The functional test with the test gas isobutylene and toluene is done in just two minutes and the Draeger X-pid 9500 is ready to use. During the test the user is guided through the user interface step-by-step. The calibration is completed within about four minutes.

Software Interfaces

The GasVision 7 software is a Windows-based software with which you can professionally visualize and evaluate the data logger of your Draeger X-pid. It is also possible to create an Excel-based export for further analyses.

The Draeger CSE Connect software solution digitizes the exchange of information during clearance measurement procedures. The data transfer between the smartphone app and the web application takes place via a cloud connection. The Draeger X-pid 9500 communicates directly with the app. This helps you to manage your measuring tasks safely and at the same time cost-effectively.

72-6AXX-A GX-6000 Six Sensor Sample Draw Gas Monitor, LEL / O2 / H2S / CO, with Alkaline Battery Pack by RKI Instruments

Simply put, the GX-6000 is a game changer. This powerful hand-held instrument is capable of simultaneously monitoring up to 6 gases. In addition to the standard 4 confined space gases which include combustibles, O2, CO, & H2S, the GX-6000 has 2 additional smart channels that accept PID, IR or super toxic sensors. Equipped with a strong internal sample pump, a man-down alarm, a panic alarm, an LED flashlight, and large auto rotating LCD display, the GX-6000 can operate as a single gas PID unit or a multifunctional tool utilizing all 6 channels. The GX-6000 with a PID sensor will come equipped with a library of over 600 VOC gases to choose from as standard. Choosing from the library is easy with a personalized favorites list of 30 commonly used VOC's as well as a list of 8 of the most recently used VOC's.

The GX-6000 has a rugged design built for the nastiest environments. It is equipped with a removable impact-resistant rubber boot and a dust and water resistant enclosure with an IP-67 rating. With 5 bright LED lights on 3 sides of the instrument, alarms are easily seen from a variety of perspectives. With vibration and loud audible alarm, GX-6000 will easily alert users when needed.

Features

• Monitor up to 6 gases
• 2 smart sensor slots auto recognize PID, IR, and super toxic sensors
• 5 Operating modes: normal, leak check, inert, snap log and bar hole
• Library of over 600 VOCs
• PPM Leak Check mode
• Man-down and panic alarms
• Auto display rotation
• LED Light source
• Internal sample pump
• Glove friendly glow in the dark buttons
• Light weight, small, rugged IP-67 design
• Interchangeable battery packs Li-ion / alkaline
• Operates up to 14 hours on Li-ion battery pack, fully recharges in 3 hours
• Field replaceable sensors, batteries and filters

Applications

• Confined space entry
• Hazmat response teams
• Arson investigation
• Remediation sites
• Perimeter monitoring
• Leak detection
• Landfill monitoring
• Wing tank entry

*Please note we can only ship RKI products to customers within the United States

10207432 Altair io360 Gas Detector, H2S Black 32pk, UL by MSA

The ALTAIR® io360 Gas Detector offers four-gas detection for high risk areas, including confined spaces, perimeter and general area monitoring. The ALTAIR io360 combines the simple set-up of a smart home device, while allowing local or remote monitoring of hazardous areas. The ultra-long battery life keeps the focus on safety and less on maintenance. The ALTAIR io360 delivers IP68 ruggedness and best-in-class, XCell sensors, the performance expected from MSA.

• Four-gas detection with a catalytic bead sensor
• Compact, portable design
• Ultra-long battery life with 50-60 days of 4-gas runtime (80 or more days as toxic & O2)
• Easy set-up, similar to a smart home product
• Factory pre-configured networks that are ready-to-go out of the box
• Android or iOS Safety io Grid mobile app makes setup and configurations simple
• Connect up to 32 ALTAIR io360 Gas Detectors with MSA HUB to form mesh network, share alarms, and extend range
• MSA HUB connects with Safety io Grid via wifi or ethernet connectivity
• Integrated D-ring and 50lb (22kg) magnet provides placement options
• IP68 toughness that can withstand submersion, sprays, and weather
• 10ft (3m) drop tested

VTS-L1231301101 Ventis MX4 Multi-Gas Monitor, LEL (Methane), CO, H2S, O2, Li-ion Battery, Desktop Charger, No Pump, Orange, UL/CSA, English by Industrial Scientific

The Ventis® MX4 is a four-gas monitor with the portability and size of a single-gas monitor. Eliminate the need for extra monitors and transition seamlessly from personal monitoring to confined space entry with the Ventis® Slide-on Pump— ideal for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries.

• Detect up to four gases with a wide range of sensor options
• Select alarm set points, set latch alarms, disable instrument shutdown while in alarm, and more
• Save time and reduce human error with maintenance and usage data available from iNet Control software
• Available with or without an integral pump, or with the Ventis Slide-on Pump for ultimate flexibility
• Non-pumped instruments compatible with 12-hour, 18-hour, or 20-hour batteries

The Ventis® Slide-on Pump

The Ventis® Slide-on Pump is ideally suited for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries. Available in black or safety orange and powered by its own battery, the slide-on pump is compatible with the Ventis MX4 and Ventis® Pro5 Multi-Gas Monitor.

• Convenient Sampling – Sample draw distance of up to 50 feet provides convenient sampling in a wide range of applications
• Easy to Attach – No tools are required to attach or remove the Ventis Slide-on Pump to or from the monitor
• Uses Same Batterys and Chargers as Ventis – Monitor and pump each use the same batterys, and can easily be exchanged between instruments
• Flexible Battery Options – Three available battery options make this pump extremely flexible in the field

GD-70D4S-CLF3-A GD-70D Smart Transmitter, 0-0.60 PPM Chlorine Trifluoride, with Strobe, in NEMA 4X Housing, 115 / 220 VAC. by RKI Instruments

RKI Instruments has been making high quality gas detection and monitoring units for over 15 years. With an emphasis on safety and reliability, RKI Instruments excels at providing the best products in gas detection and sensor technology on the market. Every year, RKI strives to improve its product offering and scours the globe for the latest technologies and innovative designs. With the introduction of the GD-70D Series Intelligent Gas Detector, employers and workplace safety managers can feel confident that they have purchased a reliable detector that is built to last.

GD-70D Series Intelligent Gas Detector

The GD-70D Series Intelligent Gas Detector is a new smart gas detection transmitter that monitors combustibles, oxygen, and a wide range of toxic gases. The unit can be used as a standalone device, integrated with other PLC systems, or integrated with RKI's Beacon series of single and multi-channel controllers. Its common platform integrates numerous detection methods and requires very little maintenance.

Exclusive Features

The plug and play intelligent sensors make for easy setup and calibration by internally retaining calibration and sensor data. This allows workers to replace sensors while in the field without the need to reprogram the equipment. For little maintenance and optimal reliability, the internal technology automatically adjusts for long-term zero and span drift. The pump flow is also self-tuning for low maintenance functioning. In general, the smart sensors use electrochemical cell detection, semiconductor detection, pyrolysis-particle detection, galvanic cell detection, and catalytic combustion detection.

The GD-70D Series features a large LCD display that easily reads all notifications and provides a color coded graph for alarm status (first and second alarms are red, and fault alarms are yellow). The LCD screen displays the pyrolyzer connection, gas concentration, detection unit of measurement, the detected gas, the maintenance status, sensor identification, the flow rate, a graph of gas concentration, error codes, and alarm points. All operational settings are completely user adjustable from the front panel. The unit also has a self-diagnosing function which detects sensor trouble and system failure. The Intelligent Gas Detector has a convenient troubleshoot feature through its firmware. This allows users to investigate and resolve their own equipment issues while minimizing maintenance costs.

Specifications

The Intelligent Gas Detector is a convenient size for workplace and wall space efficiency with dimensions of 2.8 D x 4.7 H x 5.9 D and weighs approximately 2 pounds. It can be mounted to a wall easily with a base plate and 2 or 3 screws. Sensor replacements and pump replacements can be performed quick and easily without tools.

*Please note we can only ship RKI products to customers within the United States

GD-K88AI Smart Transmitter, O2 (oxygen), 0-25%, IS type by RKI Instruments

The GD-K88Ai is a diffusion style toxic gas detection transmitter ideally suited to meet a variety of toxic gas detection needs. You can choose from a wide range of electrochemical toxic gas sensors to install in this model. The GD-K88Ai includes easy to read LCD display and push button controls for calibration. When it is used with optional intrinsic safety barriers the GD-K88Ai is safe for use in hazardous locations. The low profile design is only 1.9 inches thick and is easy to install. The hinged housing makes it easy to maintain. This transmitter can be installed with any RKI controller, or integrated to existing PLC or DCS system via 4-20mA output (24VDC two-wire, loop powered).

At the heart of any gas detector is the sensor. The sensors for the GD-K88Ai are aged and tested over a one to three month period, typically resulting in a three to five year life span, providing a lower cost of ownership for your gas detection system. These fast-responding sensors are robust electrochemical type that feature higher sensitivity and selectivity.

With over 75 years of sensor technology experience, RKI has the knowledge and capability to provide the most advanced detection techniques and manufacture the most stable and long lasting sensors in the world. As a result the GD-K88Ai is one of the most stable and long lasting toxic transmitters on the market.

Features

• Diffusion style head
• Digital readout of gas name and concentration
• External control buttons for easy maintenance
• Intrinsically safe design
• Quick response sensors
• Many toxic sensors to choose from
• 3 to 5 year typical sensor life
• Low cost of ownership

Applications

• Semiconductor manufacturing
• Petrochemical plants
• Refineries
• Water & wastewater treatment plants
• Pulp & paper mills
• Gas, telephone, & electric utilities
• Steel
• Automotive
• Refrigeration
• Food Storage
• Power plants

*Please note we can only ship RKI products to customers within the United States

6302-4105 MGS-460 Gas Detector with Remote Sensor - IP66, 3 x Relays, Analog Output, Modbus Output, Audible & Visual Alarms - R407A, 0-1,000ppm, Semi-conductor by Bacharach

Bacharach's MGS-400 Gas Detectors makes compliance with mechanical equipment room and refrigeration safety codes simple and easy, saving time and money on equipment and installation. Using the MGS-400 App, users can intuitively use, commission and maintain their gas detection system without the need for specialty training or tools. Pre-calibrated sensor modules simplify maintenance, take minutes to exchange and do not require the use of calibration gas. The MGS-400 sensors can trigger additional audio-visual alarms and act as a standalone gas detection system, or integrate easily into a BMS / BAS or with Bacharach's optional MGS-408 Gas Detection Controller.

Features

• Mobile App Interface
• Pre-calibrated Sensors
• Semi-automated Calibration
• Remote Sensor Option
• Temperature-Compensated Measurement
• Low Temperature Performance
• Digital Communications
• Analog Outputs
• Relay outputs
• Audio & Visual Alarms
• Multiple Cable Entries and Terminals

Benefits

• Quick, easy and intuitive commissioning, configuration and maintenance requires no special training. No tools required to set alarm levels and behavior
• Fast and easy sensor maintenance. Eliminates need for calibration gas.
• Easy calibration process with mobile app. Generate calibration certificates for documentation.
• Locate the sensor element in hard-to-reach areas and the base unit where convenient for electrical and communication wiring (MGS-460)
• Mitigates false alarms and optimizes accuracy in refrigeration applications.
• Suitable for use in cold rooms and freezers down to -40° F/C.
• Integrate with local BMS/BAS via Modbus RTU
• For current or voltage output to legacy systems (MGS-450/460)
• 3 relays available for alarm and fault events to active horn/strobes and ventilation (MGS-450, MGS-460)
• On-board alarm notification supports compliance with ASHRAE 15 / EN 378
• Quick and easy installation of all wiring; daisy-chain power and digital communications.

GS-BB-B-071-G Gasman Single Gas Monitor, 0-1ppm Phosgene, Non Rechargable Battery (single use), Dutch Safe Area only by Crowcon

For over 40 years, Crowcon Detection Instruments has produced state of the art gas detection devices for personal and industrial use. Building upon their reputation for reliable and innovative gas monitoring products, Crowcon introduces the Gasman personal gas monitor. Its lightweight and compact design is convenient for jobsites where workers need not be weighed down by excessive bulk and equipment. The unit conveniently clips to a pocket or helmet and operates continuously.

The Gasman personal gas monitor has numerous convenient features such as:

• One button technology
• Backlit LCD display
• Durable polycarbonate casing
• Quick response triple alert system
• Compact and lightweight design

Easy to Use

The Gasman s true one button technology is an ideal and simple design. The large glove friendly button is mounted on the front of the unit for easy access and controls all of the unit s programmable features. Also on the front, the Gasman s easy to read backlit LCD screen indicates gas readings and the battery status. The simple screen provides a clear indication of the unit s operation status. It will also alert the user 30 days in advance of when a calibration test is due. With a simple and intuitive design, Crowcon has produced a gas detector that reduces the complexities of workplace safety, and ensures workers in a straightforward manner that their equipment is on and operational.

Triple Alarm System

This portable single gas detection system features a triple alarm system that is sure to alert the user and anyone in the vicinity. The visible alarm utilizes a dual red and blue flashing LED light, and the unit houses an internal vibrating alert system. These two indicators allow for visual recognition in loud environments and working conditions. The alarm system also features a programmable audible alarm at 95 decibels. The unit is capable of a variety of alarm tones, and users can select which tone may be best for the individual workplace setting. The triple alarm system with multiple sensory indicators is sure to be noticed in almost any work environment.

Specifications

The Gasman single gas monitor is lightweight and compact, weighing less than 135 grams and with dimensions of 90 x 48 x 24 mm. The unit is available with a wide variety of gas sensors which feature various detection and alarm levels. The unit also features a quick response time of 20 seconds for flammable and toxic gases or 10 seconds for oxygen. Its datalogging feature has approximately 900 hours of storage and all events are time stamped. The battery life for this unit is incredible with 12 hours of runtime on a Rechargeable battery battery or up to 2 years on a non-Rechargeable battery.

WD-36225-59 Variable-Voltage Output Controller; 5-100%, 120V/10A by Digi-Sense

This control is designed to regulate the input voltage through the selector knob on the unit. To operate plug a resistive load into the receptacle on the back of the unit, and adjust the control dial to the desired level. The higher the selected number on the dial, the higher the voltage and hotter the load will get. This unit comes with a lattice support bracket, which is ideal for mounting to maximize space.

• Designed to regulate the input voltage through the selector knob

Includes

6' attached power cord

3300-37-003 CC 33 Fixed Transmitter with Propadiene (MAPD) (C3H4), Aluminum Housing, 0-100% LEL (MK 208-3), RS 485 No Relay by GfG

It has always been our aspiration to combine innovative ideas and technology with functional design. This is how quality and longevity come about. Attributes symbolic of the name GfG in gas measurement.

Are you looking for an innovative transmitter for flammable gases, but need explosion protection? Then a transmitter from the GfG 33 series is the right choice.

Robust housing for every application

The transmitters of the 33 series are flameproof encapsulated and fulfill the requirements of the type of protection "d". Depending on the application, you can choose the 33 transmitter with an epoxy-based aluminum or a pure stainless steel housing. In order to meet the quality requirements of our customers and our own standards in terms of durability, we use a particularly high-quality and durable Viton seal in the 33 series. This can withstand even the toughest operating conditions for many years.

Variants

GfG offers the CC 33 in two variants:

For conventional industrial The CC 33 is available in a lacquered die-cast aluminum housing with 10mm thick bulletproof glass. Applications with special conditions such as e.g. in the Food industry can be covered by a unpainted housing made of stainless steel with a 15mm thick bulletproof glass.

Operation by means of magnetic pin

The three magnetic switches behind the protective glass, which is up to 15mm thick, can be operated using the GfG magnetic pin. The GfG typical three-button operation is easy to understand. The menu is clearly structured and logically structured.

All transmitters of the 22, 29 and 33 series have a uniform user interface. The uniform operation and the logical system structure keep your training and maintenance effort as low as possible.

Proven and innovative is not a contradiction

The CC 33 works on the principle of catalytic heat generation (WT), a proven method for measuring combustible gases. The transmitters are equipped with high-performance electronics for voltage stabilization, processing of measured value output and temperature compensation. The long life of the sensors minimizes follow-up costs.

Sensor technology

With improved sensor technology and the unique GfG "chimney effect", the CC 33 transmitter for combustible gases has one of the fastest response times in the world. There are more crucial seconds left to initiate countermeasures and to bring people to safety.

Universal signal transmission

The measured values and status displays of the 33 series can be transmitted either analog or digital via the Modbus interface. Due to the different variants of signal transmission, a transmitter of the 33 series can be connected to almost any gas warning system as an additional measuring point or in exchange for existing transducers.

Signal processing

The embedded software of the 33 transmitter linearises the measurement signal and compensates for temperature influences. As a result, correct measured values are transmitted even in the event of weather-related temperature fluctuations. The execution of the software enables the detection of faults and, in the Modbus variant, the requirement of required service or maintenance work.

Smart sensors

Pre-calibrated sensor modules can be screwed directly into the sensor receptacle on the housing of the CC 33. The smart GfG sensors are pre-programmed with all the necessary parameters and can be used without much effort ("plug and play"). Sensor changes are shown in the display. (catalytic and electrochemical sensors)

Three freely programmable internal relays

The 33er transmitters can be used as a "stand-alone system". You can set the two alarm thresholds individually and freely program the optional three relays. You do not need a cable to a controller and you can nevertheless reliably switch safety-related devices.

With colored graphic display

The clearly laid-out graphic display makes it easy to read the device status, the current measured value and many other important information. In the event of an alarm, the display turns red. The large LEDs signal from a distance the current device status and thus serve the rapid information of your employees about any alarms or malfunctions.

Using the display, you can easily navigate through the clear device menu and make various settings, including calibration, depending on your user authorization.

Calibration

For regular function control with gas application, a calibration adapter is placed on the transmitter to ensure a safe and even gas supply.

BZ1-L345JR0202 Radius BZ1 Area Monitor, LEL (Methane), O2, NO2, SO2, CO/H2S, PID, No Pump, ATEx/IECEx, French by Industrial Scientific

When it comes to choosing equipment to protect your worksite from gas hazards, rely on the Radius® BZ1 Area Monitor. No other area monitor protects your workers longer in the field with less setup, user training, and time in the shop.

• Detect up to seven gases using 22 sensor options including PID
• Longest running area monitor with a typical run time of 7 days (168 hours)
• Extended Run Time Power Supply can extend battery to over 1 month
• Ultra-bright blue and red lights and attention-grabbing alarms with distinctive tones
• Audible alarms sound at 108 dB at 1 m to cut through high-noise environments
• Largest display of any area monitor on the market
• Intuitive text-based navigation and configuration
• Customizable alarm action messages such as "EVACUATE" or "VENTILATE"
• LENS™ Wireless enables communication between area monitors and Ventis® Pro5 personal monitors
• All-weather sensor deployment and 360-degree gas path for more accurate detection
• DualSense® Technology increases worker safety by using two sensors to detect the same gas

*Please note we can only ship RKI products to customers within the United States

66-5A92-02-L Air Alert Ambient Air Hazardous Gas Detector, VOC 10.6, 0-20 ppm, AC powered, non explosion proof, color alarm LEDs and horn by RKI Instruments

The RKI Air Alert series ambient air toxic gas detector is a versatile assembly that uses an electrochemical, infrared or PID sensor element to detect a variety of gases. Wire powered (12 to 35 VDC) with 4-20 mA analog and RS-485 Modbus outputs. Magnetic switches allow for non-intrusive calibration while in the field as well as full system settings and diagnostics.

Features

• Electrochemical, Infrared, or PID sensor element
• Wire powered (3-wire), 12-35 VDC operating voltage, optional AC power supply
• Operating temperature range of -40°C to +70°C
• 3 Push-button interface (ADD, MENU, SUB) with 3 corresponding magnetic, non-intrusive switches
• 2 Dry contact relays (optional)
• Graphical LCD with LED backlight
• Output options: 4-20mA (3-wire) analog, RS-485 Modbus, optional 900 MHz or 2.4 GHz radio
• Optional 3 color LED perimeter and audible alarm
• 1-Year warranty

Industry Applications

• Petrochemical plants, Refineries
• Water & wastewater treatment plants
• Pulp & paper mills
• Manufacturing facilities
• Chemical plants

*Please note we can only ship RKI products to customers within the United States

TPPLBDWA8SNNRRN Touchpoint Plus Basic Wall Mount Controller, DC Po by Honeywell Analytics

Touchpoint Plus brings a whole new control experience to your small system of gas detectors. Touchpoint Plus is an easily configurable, wall mounted control system that supports up to sixteen channels of gas detection. Its modular approach enables you to take control and configure what you need for a wide range of applications.

The signature feature of the Touchpoint line is a user-friendly touchscreen interface, and the Touchpoint Plus takes it to a new level. With this unique interface, it's easier than ever to see the status of your system at a glance - maximizing the time you have to make the right decisions. The intuitive, multilingual interface, simplifies operation and reduces training requirements. The full colour traffic light style status indication provides clarity from a distance too.

Touchpoint Plus includes a comprehensive set of outputs as standard including common alarms and dedicated drives for remote audiovisual indicators. Its modularity enables you to customise your system to meet your specific application requirements. Selecting the right detector for use with your controller can deliver significant savings in startup costs and on-going operations. Our global partner network and dedicated application specialists are able to help make the right choices for your industry.

With everything at your fingertips, you can take ownership of your system and operate it with confidence, ensuring the safety of your people and productivity of your site.

Delivering reliable control

• Honeywell reliability from the most trusted experts in gas detection
• Built-in battery backup for constant uptime
• Robust, shockproof housing for a wide range of industrial environments

Flexible capabilities

• Compatible with the full range of Honeywell gas detectors
• Powered audiovisual alarms simplify field installation
• Configuration includes easy grouping and voting alarm logic without specialist knowledge
• Next-generation compatibility
• Optional Modbus output for integration with a higher level system

Providing ease and efficiency

• Quick and easy installation, configuration, commissioning and maintenance
• Easy diagnostics, data and reporting
• Minimised training time
• Large colour touchscreen LCD
• Multilingual capabilities
• Green-yellow-red status at a glance

72-PXA-F GX-3R Pro Personal Monitor - No 4 Gas Sensors - CO2, 10,000 ppm, IR (ETA Aug 2019) - Li-Ion Battery Pack with 100-240 VAC and 12 VDC Chargers by RKI Instruments

The GX-3R Pro is the world's smallest 5-gas monitor weighing only 4.58 ounces and fits in the palm of your hand (2.9" W x 2.6" H x 1.06" D). It simultaneously monitors and displays 5 different gases. In addition to monitoring standard confined space gases, LEL, O₂, CO, & H₂S, the GX-3R Pro has a 5th channel where you can add infrared or toxic sensors. Two of the four sensor slots have interchangeable sensors providing flexible configurations, which can easily be changed in the field.

The GX-3R Pro comes equipped with Bluetooth wireless communication, man-down alarm, the choice of alkaline or rechargeable power supply, and a 3 year warranty. The Lithium-ion battery pack will operate for 25 hours and will fully charge in 3 hours.

The GX-3R Pro utilizes Bluetooth communication to display direct gas readings from the instrument to a phone app, which is available free on either iOS or Android phones. Automatic notifications can be programmed to send text or email messages, if there is an alarm event from the GX-3R Pro.

Safety supervisors will appreciate the non-compliance indicator. The instrument flashes it's 3 LED lights every 30 seconds in the following conditions; if the instrument has not been bump tested, or if calibration is due, or if there was a gas alarm event. The 3 LED lights will continue to flash once every 30 seconds until the non-compliance condition has been resolved. The 30 second interval is adjustable.

Features

• Smallest & lightest 5 gas monitor: 2.9" W x 2.6" H x 1.06" D , 4.58 ounces
• Simultaneous detection of 5 gases: LEL, O₂, H₂S, CO, and other optional sensors; H₂ Compensated CO sensor available
• Simple 2-button operation
• Bluetooth communication with iOS & Android App
• Non-Compliance Indicator
• 3 user adjustable alarm levels
• Panic Alarm - Tap instrument twice
• Man Down Alarm
• Impact resistant body
• Large full dot, auto-backlit display with auto-rotation
• Stealth mode for law enforcement
• Field replaceable sensors & filters
• Water and dust resistant design, IP66/68
• 3 Year warranty

Applications

• Personal monitoring
• Confined spaces
• Refineries/petrochemical
• Utilities
• Oil and Gas
• Water/wastewater
• Fire services
• Construction

*Please note we can only ship RKI products to customers within the United States

MX6-00034211 MX6 iBrid Multi-Gas Monitor, O2,NO2,LE,P,E by Industrial Scientific

The MX6 iBrid® is more than an intelligent hybrid of Industrial Scientific's best monitoring technologies—it's the most adaptable six-gas monitor on the market. With hundreds of possible sensor combinations, and a robust list of available configuration settings, the MX6 iBrid is ready to monitor oxygen, toxic and combustible gas, and volatile organic compounds (VOCs).

As your work changes, so can your MX6 iBrid. It uses five sensor slots to detect up to six gases. Each of those sensor slots accepts a variety of sensors, which means you can use the instrument with a PID sensor one day and an infrared sensor the next. What's more, settings allow you to adapt the instrument's behavior for your application. If you need to use a benzene PID response factor for one application, and butadiene for others, the familiar menu structure will allow you to quickly change settings.

The rugged MX6 iBrid carries our Guaranteed for Life™ warranty and is compatible with DSX™ Docking Stations. With a DSX Docking Station, maintenance is simplified and data becomes more than a spreadsheet filled with logged readings. Proactively manage your gas detection fleet—track trends, know when instrument maintenance will be required, and understand how your MX6 iBrid instruments are being used.

• 24 "Plug-and-Play" field-replaceable sensors including PID and Infrared options
• Up to 6 gases monitored simultaneously
• Simple, user-friendly, customizable, menu-driven navigation
• Five-way navigation button
• Durable, concussion-proof overmold
• Optional integral sampling pump with strong 30.5 meter (100 feet) sample draw
• Full-color graphic LCD is highly visible in a variety of lighting conditions
• Powerful, 95 dB audible alarm

MX6-LJ03C211 MX6 iBrid Multi-Gas Monitor, LEL (Methane), CO/H2S, O2, H2, Lithium-ion Extended Range Battery, UL/CSA/ATEX/IECEx, Pump, English by Industrial Scientific

The MX6 iBrid® is more than an intelligent hybrid of Industrial Scientific's best monitoring technologies—it's the most adaptable six-gas monitor on the market. With hundreds of possible sensor combinations, and a robust list of available configuration settings, the MX6 iBrid is ready to monitor oxygen, toxic and combustible gas, and volatile organic compounds (VOCs).

As your work changes, so can your MX6 iBrid. It uses five sensor slots to detect up to six gases. Each of those sensor slots accepts a variety of sensors, which means you can use the instrument with a PID sensor one day and an infrared sensor the next. What's more, settings allow you to adapt the instrument's behavior for your application. If you need to use a benzene PID response factor for one application, and butadiene for others, the familiar menu structure will allow you to quickly change settings.

The rugged MX6 iBrid carries our Guaranteed for Life™ warranty and is compatible with DSX™ Docking Stations. With a DSX Docking Station, maintenance is simplified and data becomes more than a spreadsheet filled with logged readings. Proactively manage your gas detection fleet—track trends, know when instrument maintenance will be required, and understand how your MX6 iBrid instruments are being used.

• 24 "Plug-and-Play" field-replaceable sensors including PID and Infrared options
• Up to 6 gases monitored simultaneously
• Simple, user-friendly, customizable, menu-driven navigation
• Five-way navigation button
• Durable, concussion-proof overmold
• Optional integral sampling pump with strong 30.5 meter (100 feet) sample draw
• Full-color graphic LCD is highly visible in a variety of lighting conditions
• Powerful, 95 dB audible alarm

*Please note we can only ship RKI products to customers within the United States

6400-0037 MGS-250 Infrared R514A Replacement Detector by Bacharach

Bacharach's new MGS-250 Infrared Refrigerant Gas Transmitter is the leader in performance and flexibility at an economical price. There are two versions available - a cost-effective broadband sensor used for gross leak detection or gas-particular versions that are even more distinct, pre-calibrated and characterized for response to specific refrigerants. Its simple-to-use interface gives the user the ability to set all parameters and outputs without opening the unit, moving jumpers, using mulitmeters or adjusting potentiometers.

The MGS-250 family is a cost effective solution for detecting a variety of refrigerants without the limitations posed by solid-state sensor technologies. The long-life, proprietary NDIR infrared sensor allows for accurate low-level leak detection (0-3,500 ppm), delivering up to 5-7 years of maintenance-free operation without the need for costly annual gas calibrations. Infrared sensing technology makes the MGS-250 immune to cross sensitivities to combustible and toxic gas as well as changes in temperature and humidity. The unit has an alpha-numeric LED display to show constant real-time readings, an on-board LED indicator for when the sensor is in an alarm state, and an audible alarm to alert personnel in the area that levels have exceeded the desired limit. An optional protective splash guard is available for use in areas with high water spray such as food and beverage facilities or chiller rooms.

Features & Benefits:

• Long-life, Non-Dispersive Infrared (NDIR) sensor allows for accurate low-level leak detection
• Detects all refrigerants (CFC, HFCs, HCFC, HFO's), including HFO1234YF, HFO1234ZE, R410a & R22
• Fast-responding, refrigerant-specific sensor with no cross interferences to other gases
• No field calibrations required
• Modbus RTU interface to connect to BAS/BMS systems and on-board alarm relay
• User selectable analog output: 4-20 mA, 0-5V, 1-5V, 0-10V, 2-10V
• Bright, alpha-numeric LED real-time display with on-board audible and visual alarms