All Products

Part Number: 17L-379S

Part Number: 17L-312

Part Number: P10722.5VN

Measuring Range: -30 to +50 °C tpd
Measuring Range: 0 to +100 %RH

CD600 TDS Tester with ATC and 1 point manual calibration by Milwaukee

The Milwaukee CD600 Total Dissolved Solids (TDS) Pen is designed for hydroponics, aquariums, horticulture, water conditioning and many other applications. The CD600 helps you make sure that your plants are receiving the right amount of nutrient or helps you keep your filters up-to-date and clean for water filtration. Keep TDS in your target range to help your achieve better results.

DESIGN FEATURES

• Measures Total Disolved (TDS) direct and with automatic temperature compensation.
• Ideal range for hydroponics (0 to 1990 ppm).
• Units in ppm easily convertable to μS/cm.
• Factory calibrated with the ability to recalibrate if needed.
• Automatic Temperature Compensation (ATC).
• 350 hours continuous use (4 x 1.5V batteries included).
• Simple one point calibration.

MAINTENANCE

TDS/PPM electrodes can develop nutrient build up over time. To miminize build up, always rinse the probe in fresh tap or DI water after every use.

CONVERTING TDS TO EC

The Milwaukee TDS Pen, like all TDS meters, provides a measure of Total Dissolved Solids (ppm) reading, of contaminates per unit of volume in a solution.

TDS/PPM is often converted to μS/cm. Different scales include the 500 scale, 650 scale and the 700 scale.

Your TDS/PPM readings can be approximately converted to μS/cm as shown in the examples below.

1 ppm = 2 μS/cm on the 0.5 factor scale

1 ppm = 1.43 μS/cm on the 442 scale or .70 factor scale

Old Part Number: P10728
New Part Number: P10728VN

90000-29 Traceable® Extreme-Accuracy Digital Thermometer with Calibration; 0.00/25.00/37.00C by Digi-Sense

Four Traceable International Standards Digital thermometers provide the exact readings required for critical requirements, quality control checks, and routine measurements. Units read 0.00, 25.00, 37.00, or a combination of all three with a resolution of 0.01° and an accuracy ±0.05°C within ±2°C of standard. Units read in °C and °F.

Impervious stainless-steel probe

Stainless-steel probe supplied with units shows the slightest temperature change. Probe is triple purpose for liquid, air/gas, and semisolids. Accurate readings with tip penetration of 1/3-inch. Probe has a diameter of 1/8-inch, stem length of 6-1/4 inches, overall length of 9 inches and a cable length of 5 feet.

Unit conforms to ITS-90, International Temperature Standard

Absolute high-precision thermometer is ideal for measuring temperatures in water baths, cuvets, gas systems, reagents, standards solutions, ovens, incubators, pharmaceuticals, petroleum products, foods, and wastewater.

Records time and date for MIN/MAX readings and hi/lo alarm alerts

Display shows minimum/maximum and current temperatures. MIN/MAX monitors readings overnight, on weekends, or for any time period and displays the exact time and date when the MIN/MAX temperature occurred. Alarm provides two visual (LEDs) and two audio alerts when temperature rises above or falls below high and low set points. Unit displays the exact time and date when dual thermometer alarms are triggered. Alarms are programmable in 0.1° increments. Visual and audible alarms signal continuously (for days) even if temperature returns to non-alarm range. First thermometer ever designed to permit user one-button calibration.

• Resolution is 0.01°
• Displays date and time of min/max temperature
• High and low settable alarms
• Traceable to NIST for accuracy

Includes

Stand, Velcro®, magnetic strips, and wall mount allow placing thermometer anywhere. Supplied with a Traceable® Certificate, stainless-steel probe, and two AA batteries for continuous, 1-year always-on monitoring.

Part Number: 10L-332

3614-069 D-ReX PoI Gas Detector with 5 relays, Ammonia (NH3) MK399-10, 0 - 1000 ppm by GfG

The D-ReX PoI's external sensor can be mounted in a location up to 4,000 feet / 1,200 meters away from the device and monitor toxic, combustible and corrosive gases as well as the oxygen concentration from there.

The remote sensor can be mounted directly onto pipe systems, gas cabinets and other hard-to-reach locations so that the gas detector itself can be mounted at eye level for easy access. This facilitates maintenance, inspections and operation.

With the optional saddle, it can also be used

Available Accessory:

• Mounting saddle
• Viton® (FKM) sealing for all saddle types
• M12 remote sensor cable, various sizes (3 to 100 ft / 1 to 30 m)
• Calibration cap for PoI
• Mounting brackets
• DIN rail

Features:

• 5x internal relays (form C, configurable)
• Smart sensors for more than 60 gases
• Hot-swappable smart sensor cartridge
• Tool-free maintenance
• Power-over-Ethernet (PoE) communication
• Web server for browser access
• Password-protected menu
• Interface: Analog outlet: 4 20 mA output; Digital: RS-485 (Modbus/RTU); 10/100 Mbit Ethernet (Modbus/TCP)
• Bright status and alarm LEDs
• Data logger to review sensor and alarm history
• Marked as FCC, CE, IC and UKCA

3622-156 D-ReX PoS Gas Detector with 5 relays, Acetylene (C2H2) MK221-10, 0 - 100 % LEL (CC) by GfG

Not all gases can be monitored directly at the measuring point. This may be because the maintenance of a remote sensor would be too complicated or because the target gas has to be broken down into detectable components first. This can be done using a pyrolyzer.

In these cases, the D-ReX PoS with its integrated pump is an ideal solution. The point of sampling (PoS) can be up to 100 feet / 30 meters away from the D-ReX. This also applies to the length of the recirculation hose.

Available Accessory:

• DIN rail
• PTFE hose
• Various particle filters
• Push-Pull plug-in adapter
• Angle braces

Features:

• 5x internal relays (form C, configurable)
• Smart sensors for more than 60 gases
• Hot-swappable smart sensor cartridge
• Tool-free maintenance
• Power-over-Ethernet (PoE) communication
• Web server for browser access
• Password-protected menu
• Interface: Analog outlet: 4 20 mA output; Digital: RS-485 (Modbus/RTU); 10/100 Mbit Ethernet (Modbus/TCP)
• Bright status and alarm LEDs
• Data logger to review sensor and alarm history
• Marked as FCC, CE, IC and UKCA

3624-073 D-ReX PoS Gas Detector with LIM and 5 relays, Ozone (O3) MK411-10, 0 - 1 ppm by GfG

Not all gases can be monitored directly at the measuring point. This may be because the maintenance of a remote sensor would be too complicated or because the target gas has to be broken down into detectable components first. This can be done using a pyrolyzer.

In these cases, the D-ReX PoS with its integrated pump is an ideal solution. The point of sampling (PoS) can be up to 100 feet / 30 meters away from the D-ReX. This also applies to the length of the recirculation hose.

Available Accessory:

• DIN rail
• PTFE hose
• Various particle filters
• Push-Pull plug-in adapter
• Angle braces

Features:

• 5x internal relays (form C, configurable)
• Smart sensors for more than 60 gases
• Hot-swappable smart sensor cartridge
• Tool-free maintenance
• Power-over-Ethernet (PoE) communication
• Web server for browser access
• Password-protected menu
• Interface: Analog outlet: 4 20 mA output; Digital: RS-485 (Modbus/RTU); 10/100 Mbit Ethernet (Modbus/TCP)
• Bright status and alarm LEDs
• Data logger to review sensor and alarm history
• Marked as FCC, CE, IC and UKCA

VTS-L1232201101 Ventis MX4 Personal Gas Monitor, LEL (CH4), CO, H2S, O2, Li-ion Ext Range, Desktop Charger/Datalink, Without Pump, Orange, UL/CSA, English by Industrial Scientific

The Ventis® MX4 is a four-gas monitor with the portability and size of a single-gas monitor. Eliminate the need for extra monitors and transition seamlessly from personal monitoring to confined space entry with the Ventis® Slide-on Pump— ideal for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries.

• Detect up to four gases with a wide range of sensor options
• Select alarm set points, set latch alarms, disable instrument shutdown while in alarm, and more
• Save time and reduce human error with maintenance and usage data available from iNet Control software
• Available with or without an integral pump, or with the Ventis Slide-on Pump for ultimate flexibility
• Non-pumped instruments compatible with 12-hour, 18-hour, or 20-hour batteries

The Ventis® Slide-on Pump

The Ventis® Slide-on Pump is ideally suited for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries. Available in black or safety orange and powered by its own battery, the slide-on pump is compatible with the Ventis MX4 and Ventis® Pro5 Multi-Gas Monitor.

• Convenient Sampling – Sample draw distance of up to 50 feet provides convenient sampling in a wide range of applications
• Easy to Attach – No tools are required to attach or remove the Ventis Slide-on Pump to or from the monitor
• Uses Same Batterys and Chargers as Ventis – Monitor and pump each use the same batterys, and can easily be exchanged between instruments
• Flexible Battery Options – Three available battery options make this pump extremely flexible in the field

GHS1284VY Class 2.1 Dangerous Goods Laser Drum Labels (Vinyl), 100/Pkg by GHS Safety

GHS pre-printed drum labels come with your choice of pictogram that meets the UN recommendations on the Transport of Dangerous Goods. These labels make an excellent choice for short production runs or re-labeling of product for transportation. These labels are printed on a Laser Printable Paper or Vinyl stock with a permanent peel and stick adhesive. Use any desktop publishing package to quickly make your own transportation labels. Available in 8.5" x 14" size and packaged in bundles of 100 sheets.