All Products

6302-1126 MGS-450 Gas Detector - IP41, 3 x Relays, Analog Output, Modbus Output, Audible & Visual Alarms - R407F, 0-1,000ppm, Semi-conductor by Bacharach

Bacharach's MGS-400 Gas Detectors makes compliance with mechanical equipment room and refrigeration safety codes simple and easy, saving time and money on equipment and installation. Using the MGS-400 App, users can intuitively use, commission and maintain their gas detection system without the need for specialty training or tools. Pre-calibrated sensor modules simplify maintenance, take minutes to exchange and do not require the use of calibration gas. The MGS-400 sensors can trigger additional audio-visual alarms and act as a standalone gas detection system, or integrate easily into a BMS / BAS or with Bacharach's optional MGS-408 Gas Detection Controller.

Features

• Mobile App Interface
• Pre-calibrated Sensors
• Semi-automated Calibration
• Remote Sensor Option
• Temperature-Compensated Measurement
• Low Temperature Performance
• Digital Communications
• Analog Outputs
• Relay outputs
• Audio & Visual Alarms
• Multiple Cable Entries and Terminals

Benefits

• Quick, easy and intuitive commissioning, configuration and maintenance requires no special training. No tools required to set alarm levels and behavior
• Fast and easy sensor maintenance. Eliminates need for calibration gas.
• Easy calibration process with mobile app. Generate calibration certificates for documentation.
• Locate the sensor element in hard-to-reach areas and the base unit where convenient for electrical and communication wiring (MGS-460)
• Mitigates false alarms and optimizes accuracy in refrigeration applications.
• Suitable for use in cold rooms and freezers down to -40° F/C.
• Integrate with local BMS/BAS via Modbus RTU
• For current or voltage output to legacy systems (MGS-450/460)
• 3 relays available for alarm and fault events to active horn/strobes and ventilation (MGS-450, MGS-460)
• On-board alarm notification supports compliance with ASHRAE 15 / EN 378
• Quick and easy installation of all wiring; daisy-chain power and digital communications.

TPPLBAWV8S4BNNN Touchpoint Plus Basic Wall Mount Controller, AC115/220 150W, 8 x mV input with 12 x relay output, 4 x mA output, battery backup by Honeywell Analytics

Touchpoint Plus brings a whole new control experience to your small system of gas detectors. Touchpoint Plus is an easily configurable, wall mounted control system that supports up to sixteen channels of gas detection. Its modular approach enables you to take control and configure what you need for a wide range of applications.

The signature feature of the Touchpoint line is a user-friendly touchscreen interface, and the Touchpoint Plus takes it to a new level. With this unique interface, it's easier than ever to see the status of your system at a glance - maximizing the time you have to make the right decisions. The intuitive, multilingual interface, simplifies operation and reduces training requirements. The full colour traffic light style status indication provides clarity from a distance too.

Touchpoint Plus includes a comprehensive set of outputs as standard including common alarms and dedicated drives for remote audiovisual indicators. Its modularity enables you to customise your system to meet your specific application requirements. Selecting the right detector for use with your controller can deliver significant savings in startup costs and on-going operations. Our global partner network and dedicated application specialists are able to help make the right choices for your industry.

With everything at your fingertips, you can take ownership of your system and operate it with confidence, ensuring the safety of your people and productivity of your site.

Delivering reliable control

• Honeywell reliability from the most trusted experts in gas detection
• Built-in battery backup for constant uptime
• Robust, shockproof housing for a wide range of industrial environments

Flexible capabilities

• Compatible with the full range of Honeywell gas detectors
• Powered audiovisual alarms simplify field installation
• Configuration includes easy grouping and voting alarm logic without specialist knowledge
• Next-generation compatibility
• Optional Modbus output for integration with a higher level system

Providing ease and efficiency

• Quick and easy installation, configuration, commissioning and maintenance
• Easy diagnostics, data and reporting
• Minimised training time
• Large colour touchscreen LCD
• Multilingual capabilities
• Green-yellow-red status at a glance

VTS-K5232100101 Ventis MX4 Multi-Gas Monitor, LEL (Pentane), SO2, H2S, O2, Li-ion Ext Range, Desktop Charger, Without Pump, Black, UL/CSA, English by Industrial Scientific

The Ventis® MX4 is a four-gas monitor with the portability and size of a single-gas monitor. Eliminate the need for extra monitors and transition seamlessly from personal monitoring to confined space entry with the Ventis® Slide-on Pump— ideal for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries.

• Detect up to four gases with a wide range of sensor options
• Select alarm set points, set latch alarms, disable instrument shutdown while in alarm, and more
• Save time and reduce human error with maintenance and usage data available from iNet Control software
• Available with or without an integral pump, or with the Ventis Slide-on Pump for ultimate flexibility
• Non-pumped instruments compatible with 12-hour, 18-hour, or 20-hour batteries

The Ventis® Slide-on Pump

The Ventis® Slide-on Pump is ideally suited for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries. Available in black or safety orange and powered by its own battery, the slide-on pump is compatible with the Ventis MX4 and Ventis® Pro5 Multi-Gas Monitor.

• Convenient Sampling – Sample draw distance of up to 50 feet provides convenient sampling in a wide range of applications
• Easy to Attach – No tools are required to attach or remove the Ventis Slide-on Pump to or from the monitor
• Uses Same Batterys and Chargers as Ventis – Monitor and pump each use the same batterys, and can easily be exchanged between instruments
• Flexible Battery Options – Three available battery options make this pump extremely flexible in the field

AI467 SX731 Handheld pH/ORP/Conductivity/TDS/Salinity/Resistivity Multiparameter Meter Kit by Apera

Apera SX731 is designed for lab-grade measurement of up to 7 water quality parameters in the field, including pH, ORP (redox), conductivity, TDS, salinity, resistivity, and temperature. It is suitable for general water solutions applications such as water treatment, groundwater, surface water, hydroponics, environmental monitoring, aquaculture, aquarium, beverage making, etc.

Basic Features

• Intelligent functions – auto. calibration, auto. temperature compensation, self-diagnosis, data logging, auto. power off, and more.
• Digital filter technology – enhance the meter's response time and measurement accuracy
• Automatic electrode recognition – the meter automatically switches to the right parameter mode according to the connected electrode
• Data logging – 400 sets of data storage and recall
• Built tough – IP57 water-resistant structure, ideal for use in harsh environment

TPPLBDWV8D4NNNN Touchpoint Plus Basic Wall Mount Controller, DC Powered, 8 x mV input with 24 x relay output, 4 x mA output by Honeywell Analytics

Touchpoint Plus brings a whole new control experience to your small system of gas detectors. Touchpoint Plus is an easily configurable, wall mounted control system that supports up to sixteen channels of gas detection. Its modular approach enables you to take control and configure what you need for a wide range of applications.

The signature feature of the Touchpoint line is a user-friendly touchscreen interface, and the Touchpoint Plus takes it to a new level. With this unique interface, it's easier than ever to see the status of your system at a glance - maximizing the time you have to make the right decisions. The intuitive, multilingual interface, simplifies operation and reduces training requirements. The full colour traffic light style status indication provides clarity from a distance too.

Touchpoint Plus includes a comprehensive set of outputs as standard including common alarms and dedicated drives for remote audiovisual indicators. Its modularity enables you to customise your system to meet your specific application requirements. Selecting the right detector for use with your controller can deliver significant savings in startup costs and on-going operations. Our global partner network and dedicated application specialists are able to help make the right choices for your industry.

With everything at your fingertips, you can take ownership of your system and operate it with confidence, ensuring the safety of your people and productivity of your site.

Delivering reliable control

• Honeywell reliability from the most trusted experts in gas detection
• Built-in battery backup for constant uptime
• Robust, shockproof housing for a wide range of industrial environments

Flexible capabilities

• Compatible with the full range of Honeywell gas detectors
• Powered audiovisual alarms simplify field installation
• Configuration includes easy grouping and voting alarm logic without specialist knowledge
• Next-generation compatibility
• Optional Modbus output for integration with a higher level system

Providing ease and efficiency

• Quick and easy installation, configuration, commissioning and maintenance
• Easy diagnostics, data and reporting
• Minimised training time
• Large colour touchscreen LCD
• Multilingual capabilities
• Green-yellow-red status at a glance

GS-AC-A-006-G Gasman Single Gas Monitor, 0-100% LEL Pentane, Rechargable Battery, German ATEX by Crowcon

For over 40 years, Crowcon Detection Instruments has produced state of the art gas detection devices for personal and industrial use. Building upon their reputation for reliable and innovative gas monitoring products, Crowcon introduces the Gasman personal gas monitor. Its lightweight and compact design is convenient for jobsites where workers need not be weighed down by excessive bulk and equipment. The unit conveniently clips to a pocket or helmet and operates continuously.

The Gasman personal gas monitor has numerous convenient features such as:

• One button technology
• Backlit LCD display
• Durable polycarbonate casing
• Quick response triple alert system
• Compact and lightweight design

Easy to Use

The Gasman s true one button technology is an ideal and simple design. The large glove friendly button is mounted on the front of the unit for easy access and controls all of the unit s programmable features. Also on the front, the Gasman s easy to read backlit LCD screen indicates gas readings and the battery status. The simple screen provides a clear indication of the unit s operation status. It will also alert the user 30 days in advance of when a calibration test is due. With a simple and intuitive design, Crowcon has produced a gas detector that reduces the complexities of workplace safety, and ensures workers in a straightforward manner that their equipment is on and operational.

Triple Alarm System

This portable single gas detection system features a triple alarm system that is sure to alert the user and anyone in the vicinity. The visible alarm utilizes a dual red and blue flashing LED light, and the unit houses an internal vibrating alert system. These two indicators allow for visual recognition in loud environments and working conditions. The alarm system also features a programmable audible alarm at 95 decibels. The unit is capable of a variety of alarm tones, and users can select which tone may be best for the individual workplace setting. The triple alarm system with multiple sensory indicators is sure to be noticed in almost any work environment.

Specifications

The Gasman single gas monitor is lightweight and compact, weighing less than 135 grams and with dimensions of 90 x 48 x 24 mm. The unit is available with a wide variety of gas sensors which feature various detection and alarm levels. The unit also features a quick response time of 20 seconds for flammable and toxic gases or 10 seconds for oxygen. Its datalogging feature has approximately 900 hours of storage and all events are time stamped. The battery life for this unit is incredible with 12 hours of runtime on a Rechargeable battery battery or up to 2 years on a non-Rechargeable battery.

M-512522 Manning AirScan IRF9 Transmitter, R404A 0-3,000 ppm, ATMOS, stainless steel enclosure by Honeywell Analytics

The industrial refrigeration industry is changing rapidly. The manufacture of R-22 and other HCFCs are being phased out. Influential organizations such as EPA and CARB (California Air Resources Board) are enforcing lower level monitoring requirements. Manufacturers of cooling systems are introducing new equipment that runs on 407a, 422d, 410a, HFO-1234yf, NH3 and CO2. In step with these changes, EPA fines have escalated for anyone venting ozone-depleting gases. What's your best move? Contact Honeywell Analytics to learn how to detect for these new refrigerants. With Honeywell Analytics, you can green the environment—and green your bottom line.

Honeywell Analytics Infrared monitoring solutions are designed to help your plant operate more efficiently and cost effectively. Unlike sample draw systems which take longer to pinpoint a gas leak, our diffusion sensing technology cuts downtime and the cost of expensive refrigerant replacement. Other technological advantages include flexible standalone or networkable configurations, long operating life expectancy (10+ years); fewer calibration requirements; self-monitoring SensorCheck technology; EPA compliance including newer requirements set by CARB (California Air Resources Board); and accurate, reliable response to the most common refrigerant gases used in industrial or commercial processes.

Refrigerant Specific

• Rapid response to refrigerants including R-404a, R-22, R-507a, R-134a, R-407a, R-410a, R-422d, HFO-1234yf, NH3 and CO2
• Internal monitoring of 4/20 mA loop circuitry continuously
• Compliant with new monitoring standards set by CARB

Diffusion-Design Sensor

• Has no moving parts and doesn't require pumps or filters
• All points of detection can be monitored continuously at an affordable cost

Versatility

• Can be used with any Honeywell Analytics readout
• Standard range of 0-3,000 ppm, can be rescaled for lower trip points
• Provides a linear output of 4/20 mA as a function of refrigerant concentration
• Simple, real-time calibration eliminates maintenance downtime
• Automatically adapts to fluctuating temperatures

Long-Lasting Performance

• Unique internal reference channel compensates for dust particles, source degradation, humidity and temperature fluctuation, food odors, chemical cleaners, etc.

ATMOS™ Technology

• Allows for operation down to -60°F and in condensing humidity environments or during washdown
• Automatically adapts to its environment and provides accurate and reliable performance under the harshest conditions

SensorCheck™ Technology

• Checks operating parameters of sensors and sends a notification output signal if an anomaly is identified
• Tests the sensor every 24 hours for electrical viability
• Indication can be detected by a Manning gas monitor or PLC

Housing

• High-mass metal bench provides structural and thermal stability and greater immunity to vibration
• Superior EMI/RFI shielding

Applications

• Banana and Produce Rooms
• Beverage Plants
• Wineries and Breweries
• Confined Space Entry
• Food Processing
• Gas Bottling Plants
• Ice Rinks
• Product Coolers
• Rack Houses
• Refrigeration Systems
• Supermarkets

VTS-L0002110201 Ventis MX4 Multi-Gas Monitor, LEL (CH4), Li-ion Ext Range, Desktop Charger, Pump, Black, ATEX/IECEX, English by Industrial Scientific

The Ventis® MX4 is a four-gas monitor with the portability and size of a single-gas monitor. Eliminate the need for extra monitors and transition seamlessly from personal monitoring to confined space entry with the Ventis® Slide-on Pump— ideal for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries.

• Detect up to four gases with a wide range of sensor options
• Select alarm set points, set latch alarms, disable instrument shutdown while in alarm, and more
• Save time and reduce human error with maintenance and usage data available from iNet Control software
• Available with or without an integral pump, or with the Ventis Slide-on Pump for ultimate flexibility
• Non-pumped instruments compatible with 12-hour, 18-hour, or 20-hour batteries

The Ventis® Slide-on Pump

The Ventis® Slide-on Pump is ideally suited for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries. Available in black or safety orange and powered by its own battery, the slide-on pump is compatible with the Ventis MX4 and Ventis® Pro5 Multi-Gas Monitor.

• Convenient Sampling – Sample draw distance of up to 50 feet provides convenient sampling in a wide range of applications
• Easy to Attach – No tools are required to attach or remove the Ventis Slide-on Pump to or from the monitor
• Uses Same Batterys and Chargers as Ventis – Monitor and pump each use the same batterys, and can easily be exchanged between instruments
• Flexible Battery Options – Three available battery options make this pump extremely flexible in the field

81-SDM6000-02 SDM-6000 Calibration Station for GX-6000, includes Particle Filter, Connection Brackets, Exhaust Tubing, USB Cable for PC, SD Card, USB SD Card Reader, Ethernet Cable, and Multi-unit AC Adapter by RKI Instruments

Stand Alone Station

Modular Design

Up to 10 calibration stations can also be connected to one PC for automated charging, calibration, bump testing and archiving of data. Even if instruments are turned off, automated routines will power up the instruments and run as scheduled. All data collected from the PC Controlled software can also be centralized in one network location accessible by anyone with the PC Controlled software with access to the network location.

Stand Alone Station Features

• Stand-alone station (no PC Required)
• Charge, calibrate, bump test, and alarm test
• Included software collects calibration, bump test, alarm history, and exposure date from instruments
• Automatically power instruments on / off for scheduled calibration
• Accepts GX-6000 with or without rubber boot

Modular Design

• Simultaneously bump / calibrate, charge, and collect data up to 10 instruments
• No tubing, adaptors or wires needed to connect
• One power source for all stations
• Configure GX-6000 parameters
• Centralize instrument data from multiple stations and locations to one network location
• Ethernet port for LAN connectivity
• Schedule automatic calibration / bump test
• Optional valve expansion module for up to six gas cylinders
• Optional battery operated printer

*Please note we can only ship RKI products to customers within the United States

MX6-L673R217 MX6 iBrid Multi-Gas Monitor, LEL (Methane), NH3, Cl2, O2, PID, Lithium-ion Extended Range Battery, UL/CSA/ATEX/IECEx, Pump, Portugese by Industrial Scientific

The MX6 iBrid® is more than an intelligent hybrid of Industrial Scientific's best monitoring technologies—it's the most adaptable six-gas monitor on the market. With hundreds of possible sensor combinations, and a robust list of available configuration settings, the MX6 iBrid is ready to monitor oxygen, toxic and combustible gas, and volatile organic compounds (VOCs).

As your work changes, so can your MX6 iBrid. It uses five sensor slots to detect up to six gases. Each of those sensor slots accepts a variety of sensors, which means you can use the instrument with a PID sensor one day and an infrared sensor the next. What's more, settings allow you to adapt the instrument's behavior for your application. If you need to use a benzene PID response factor for one application, and butadiene for others, the familiar menu structure will allow you to quickly change settings.

The rugged MX6 iBrid carries our Guaranteed for Life™ warranty and is compatible with DSX™ Docking Stations. With a DSX Docking Station, maintenance is simplified and data becomes more than a spreadsheet filled with logged readings. Proactively manage your gas detection fleet—track trends, know when instrument maintenance will be required, and understand how your MX6 iBrid instruments are being used.

• 24 "Plug-and-Play" field-replaceable sensors including PID and Infrared options
• Up to 6 gases monitored simultaneously
• Simple, user-friendly, customizable, menu-driven navigation
• Five-way navigation button
• Durable, concussion-proof overmold
• Optional integral sampling pump with strong 30.5 meter (100 feet) sample draw
• Full-color graphic LCD is highly visible in a variety of lighting conditions
• Powerful, 95 dB audible alarm

72-6ABX-G GX-6000 Six Sensor Sample Draw Gas Monitor, LEL / O2 / H2S / CO / VOC (6000ppm), with Alkaline & Li-ion Battery Packs / 100-240 VAC & 12 VDC Charger by RKI Instruments

Simply put, the GX-6000 is a game changer. This powerful hand-held instrument is capable of simultaneously monitoring up to 6 gases. In addition to the standard 4 confined space gases which include combustibles, O2, CO, & H2S, the GX-6000 has 2 additional smart channels that accept PID, IR or super toxic sensors. Equipped with a strong internal sample pump, a man-down alarm, a panic alarm, an LED flashlight, and large auto rotating LCD display, the GX-6000 can operate as a single gas PID unit or a multifunctional tool utilizing all 6 channels. The GX-6000 with a PID sensor will come equipped with a library of over 600 VOC gases to choose from as standard. Choosing from the library is easy with a personalized favorites list of 30 commonly used VOC's as well as a list of 8 of the most recently used VOC's.

The GX-6000 has a rugged design built for the nastiest environments. It is equipped with a removable impact-resistant rubber boot and a dust and water resistant enclosure with an IP-67 rating. With 5 bright LED lights on 3 sides of the instrument, alarms are easily seen from a variety of perspectives. With vibration and loud audible alarm, GX-6000 will easily alert users when needed.

Features

• Monitor up to 6 gases
• 2 smart sensor slots auto recognize PID, IR, and super toxic sensors
• 5 Operating modes: normal, leak check, inert, snap log and bar hole
• Library of over 600 VOCs
• PPM Leak Check mode
• Man-down and panic alarms
• Auto display rotation
• LED Light source
• Internal sample pump
• Glove friendly glow in the dark buttons
• Light weight, small, rugged IP-67 design
• Interchangeable battery packs Li-ion / alkaline
• Operates up to 14 hours on Li-ion battery pack, fully recharges in 3 hours
• Field replaceable sensors, batteries and filters

Applications

• Confined space entry
• Hazmat response teams
• Arson investigation
• Remediation sites
• Perimeter monitoring
• Leak detection
• Landfill monitoring
• Wing tank entry

*Please note we can only ship RKI products to customers within the United States

3615-203 D-ReX PoL Gas Detector with 5 relays and Enclosure, Carbon dioxide (CO2) MK252-10, 0 - 25% vol. by GfG

The D-ReX is a very user-friendly, easy-to-maintain gas detector.

High-resolution, full-color display

The 2.4, 320 x 240 pixel full-color TFT display sets new standards for gas detectors. It provides clear and precise information about the current measured values, the short-term and long-term exposure, as well as any malfunctions that may have occurred. Information can be displayed in a variety of languages and scripts, including English, German and Simplified Chinese.

Clear Information

No longer will you have to decipher cryptic error codes – information on any issue is instead displayed in plain text. Status LEDs provide an additional instant overview of vital components of the system.

Intuitive device management using Bluetooth and app

Settings on the D-ReX can easily be managed using the configuration program or the GfG app (Android). They can be connected to the device either via RJ45 an interface or Bluetooth. This will give you access to all settings and configuration options. After entering the password, changes can also be made using the control keys in the D-ReX's service menu.

Advanced connectivity

The D-ReX comes with a wide variety of communication interfaces: Choose between analog, industry standard 4-20 mA, digital RS-485 interface (Modbus/RTU), Ethernet (Modbus/TCP) and LonWorks (optional) for signal transmission. The Bluetooth option enables wireless connectivity. In addition to the five internal, programmable changeover contact relays (optional), 16 additional relays can be addressed by connecting the D-ReX to a GMA200-RT/D relay module.

Periodic sensor self-tests

The plug-and-play smart sensor cartridges are pre-configured and pre-calibrated for easy installation or replacement. Automatic sensor self-tests increase safety while reducing maintenance costs even further.

The new Standard for Versatility: D-ReX

All the advantages mentioned perfectly qualify the D-ReX for numerous applications in virtually all industries. Some of its unique features make it particularly suitable for use in the semiconductor industry, photovoltaic industry and industrial manufacturing as well as in laboratories. If you are looking for the gas detector that best suits your needs, the D-ReX will be your first choice for many applications.

Possible areas of application:

• MRI Labs
• Process tools
• Vacuum pumps
• Scrubbers
• Gas cabinets
• Ambient breathing zones
• Storage areas
• Cleanroom environments
• Sub fab systems

Features:

• Sensors for more than 30 gases
• Hot-swappable smart sensor cartridge
• High-resolution, full-color 2.4" TFT display
• Plain text information
• Tool-free maintenance
• Power-over-Ethernet (PoE) communication
• Can be addresses via web portal
• Password-protected menu
• Interface: Analog: 4 20 mA output; Digital: RS-485 (Modbus/RTU); 10/100 Mbit Ethernet (Modbus/TCP)
• Bright status and alarm LEDs
• Data logger to review sensor and alarms history
• CE marked and UL certified

USPs:

• Tube length up to 30 m / 100 ft.
• Extension cable 1 m / 30 m
• Easy to replace mechanical component of internal pump
• Bluetooth®

Options:

• 16x external relays (GMA200-RT/D)
• Line Integrity Monitoring

1290-0073 Vertex M Rack (110 VAC) with One (1) Pyrolyzer Analyzer by Honeywell Analytics

Vertex M is the industry's most flexible, advanced toxic gas monitoring system offering parts per billion detection levels and physical evidence of a gas leak. Vertex M ensures productivity as well as life safety.

Flexible

The Vertex M System includes as standard one eight-point analyzer. As your monitoring needs change, Vertex M expands, offering you up to 24 points of continuous gas detection. Place your sampling points up to 400 feet (120 meters) from the system. There is a choice of universal analyzer modules and/or pyrolyzer analyzers. (Note: If Vertex M is used with one pyrolyzer module, the maximum number of points of detection is 16.)

Reliable

Vertex M offers powerful, built-in system redundancy as standard equipment to effectively safeguard against downtime.

• Back-up pump and internal power module
• Chemcassette® technology provides physical evidence of gas event
• System data back-up (if main data acquisition PC fails, analyzers continue to monitor, log data and alarm)
• Automated leak test with line integrity option

Easy to use

• Touch screen for easy access to data
• Software updates via CD-ROM or network to all system components
• Configuration profile editing and data retrieval are all achievable without taking unit offline
• Radio frequency identification tag (RFID) ensures Chemcassettes® are installed into appropriately programmed analyzer, eliminating human error
• On-line help system

Security

• Multiple levels of password protection
• Reconfigure security setup without taking unit offline

Low cost of ownership

• Vertex's M smaller footprint and greater density of points reduce your cost per point
• Eight points per analyzer lowers Chemcassette® costs
• Maximized 24 point systems provide low cost per point as compared to other continuous monitors
• One system monitors up to three gas families and more than 40 gases
• You can split your sample to more than one analyzer

Easy to maintain

• Vertex M uses cost-effective XP Chemcassettes®, providing up to three months of continuous monitoring
• Simplified replacement of Chemcassettes® and automated optics verification
• No dynamic calibration required
• One-touch flow balancing
• Easy access to analyzers, pumps, power supplies and touch screen from front panel
• Onscreen interactive electronic manual

Advanced communications

• Built-in configurable PLCs with optional 64 relay contacts non-isolated; 32 isolated
• Standard OPC interface for easy integration into your existing factory automation system or HMI
• Optional Ethernet/CIP, LONWORKS®, DeviceNetTM, DF1 Interface, PROFIBUS, Modbus Plus, Modbus/TCP, ControlNet or 4-20mA outputs available
• Optional Chemcam camera permits viewing of stain, locally or remotely, for proof of gas event. Image is electronically saved for future retrieval.
• Optional remote control/viewing software enables total visualization of the monitor screens at a remote PC

GS-BG-B-071-G Gasman Single Gas Monitor, 0-500ppm Hydrogen Sulphide, Non Rechargable Battery (single use), Dutch Safe Area only by Crowcon

For over 40 years, Crowcon Detection Instruments has produced state of the art gas detection devices for personal and industrial use. Building upon their reputation for reliable and innovative gas monitoring products, Crowcon introduces the Gasman personal gas monitor. Its lightweight and compact design is convenient for jobsites where workers need not be weighed down by excessive bulk and equipment. The unit conveniently clips to a pocket or helmet and operates continuously.

The Gasman personal gas monitor has numerous convenient features such as:

• One button technology
• Backlit LCD display
• Durable polycarbonate casing
• Quick response triple alert system
• Compact and lightweight design

Easy to Use

The Gasman s true one button technology is an ideal and simple design. The large glove friendly button is mounted on the front of the unit for easy access and controls all of the unit s programmable features. Also on the front, the Gasman s easy to read backlit LCD screen indicates gas readings and the battery status. The simple screen provides a clear indication of the unit s operation status. It will also alert the user 30 days in advance of when a calibration test is due. With a simple and intuitive design, Crowcon has produced a gas detector that reduces the complexities of workplace safety, and ensures workers in a straightforward manner that their equipment is on and operational.

Triple Alarm System

This portable single gas detection system features a triple alarm system that is sure to alert the user and anyone in the vicinity. The visible alarm utilizes a dual red and blue flashing LED light, and the unit houses an internal vibrating alert system. These two indicators allow for visual recognition in loud environments and working conditions. The alarm system also features a programmable audible alarm at 95 decibels. The unit is capable of a variety of alarm tones, and users can select which tone may be best for the individual workplace setting. The triple alarm system with multiple sensory indicators is sure to be noticed in almost any work environment.

Specifications

The Gasman single gas monitor is lightweight and compact, weighing less than 135 grams and with dimensions of 90 x 48 x 24 mm. The unit is available with a wide variety of gas sensors which feature various detection and alarm levels. The unit also features a quick response time of 20 seconds for flammable and toxic gases or 10 seconds for oxygen. Its datalogging feature has approximately 900 hours of storage and all events are time stamped. The battery life for this unit is incredible with 12 hours of runtime on a Rechargeable battery battery or up to 2 years on a non-Rechargeable battery.

GS-AI-A-008-G Gasman Single Gas Monitor, 0-100ppm Hydrogen Sulphide, Rechargable Battery, Italian ATEX by Crowcon

For over 40 years, Crowcon Detection Instruments has produced state of the art gas detection devices for personal and industrial use. Building upon their reputation for reliable and innovative gas monitoring products, Crowcon introduces the Gasman personal gas monitor. Its lightweight and compact design is convenient for jobsites where workers need not be weighed down by excessive bulk and equipment. The unit conveniently clips to a pocket or helmet and operates continuously.

The Gasman personal gas monitor has numerous convenient features such as:

• One button technology
• Backlit LCD display
• Durable polycarbonate casing
• Quick response triple alert system
• Compact and lightweight design

Easy to Use

The Gasman s true one button technology is an ideal and simple design. The large glove friendly button is mounted on the front of the unit for easy access and controls all of the unit s programmable features. Also on the front, the Gasman s easy to read backlit LCD screen indicates gas readings and the battery status. The simple screen provides a clear indication of the unit s operation status. It will also alert the user 30 days in advance of when a calibration test is due. With a simple and intuitive design, Crowcon has produced a gas detector that reduces the complexities of workplace safety, and ensures workers in a straightforward manner that their equipment is on and operational.

Triple Alarm System

This portable single gas detection system features a triple alarm system that is sure to alert the user and anyone in the vicinity. The visible alarm utilizes a dual red and blue flashing LED light, and the unit houses an internal vibrating alert system. These two indicators allow for visual recognition in loud environments and working conditions. The alarm system also features a programmable audible alarm at 95 decibels. The unit is capable of a variety of alarm tones, and users can select which tone may be best for the individual workplace setting. The triple alarm system with multiple sensory indicators is sure to be noticed in almost any work environment.

Specifications

The Gasman single gas monitor is lightweight and compact, weighing less than 135 grams and with dimensions of 90 x 48 x 24 mm. The unit is available with a wide variety of gas sensors which feature various detection and alarm levels. The unit also features a quick response time of 20 seconds for flammable and toxic gases or 10 seconds for oxygen. Its datalogging feature has approximately 900 hours of storage and all events are time stamped. The battery life for this unit is incredible with 12 hours of runtime on a Rechargeable battery battery or up to 2 years on a non-Rechargeable battery.

E1500-NP Portable Industrial Combustion Gas & Emissions Analyzer by E Instruments

The E1500 is a hand-held industrial combustion gas and emissions analyzer that is a valuable tool designed for maintenance and tuning of combustion processes including boilers, burners, gas and diesel engines, turbines, furnaces, kilns, heaters, and laboratory analysis.

Accurate / Reliable / Robust / Fast

• Built-In Printer
• Draft & Differential Pressure
• Flue and Ambient Temp
• Customizable Display Screen & Print out
• Built-In Manometer
• Combustion Efficiency
• Automatic Data Logging
• Internal Memory (2,000 tests)

• O₂, & CO with Calculated CO₂
• Built-In Printer Non-Fading Paper
• Full Color Graphic Display
• Field Replaceable Sensors
• PC Software with Bluetooth®
• iOS and Android Mobile Applications

E1500 Features

• Built-In Printer (Non-Fading Paper)
• Simple Menu Interface with Full Color Graphic Display
• Magnetic Rubber Holster
• Unbreakable Metal Connections
• Pre-Calibrated Field Replaceable Sensors
• Automatic Data Logging
• PC Software, Bluetooth® & App Included

Standard Probe Details:

• 12" (300mm) probe
• 1470 °F (800 °C) max
• 10' (3m) Dual Hose
• Longer & High Temperature Probes available

E1500-NP Kits Include:

• O₂ (0-25%) and CO (0-8000ppm) Field Replaceable Sensors
• Stack Gas & Ambient Air Temperature Measurements
• Draft & Differential Pressure Measurements
• Efficiency, Loss, Excess Air, & CO₂ Calculations
• 12" (300mm) Probe with 10' (3m) Dual Hose
• Water Trap Assembly with Filter Cartridge
• Large Full Color Graphic Display Screen
• Rechargeable Lithium Ion Battery Pack with AC Charger
• Internal Memory for Data Storage (2000 Tests)
• NO PRINTER
• QR Code Smartphone Apps (iOS & Android)
• Wireless REAL-TIME Bluetooth Smartphone App
• Automatic Periodic Data Saving (Data Logger)
• Software Package with BlueTooth & USB Cable
• Protective Rubber Holster
• Magnetic Support
• Protective Vinyl Carrying Case
• Instruction Manual
• Calibration Certificate

37803-91 Traceable Thermocouple Thermometer with Data Output and Calibration by Digi-Sense

Traceable® Products have an individually-numbered Traceable® Certificate provided with each unit, that assures accuracy from our ISO/IEC 17025:2017(1750.01) calibration laboratory accredited by A2LA. It indicates traceability of measurements to the SI units through NIST or other recognized national measurement institutes (NMI) that are signatories to the CIPM Mutual Recognition Agreement. Each product goes through an intense vetting process before it can carry the Traceable name, thus saving you both time and money by not having to calibrate separately.

• Includes NIST-Traceable certificate from our A2LA accredited (1750.01) calibration laboratory
• Temperature range is -50 to 1999°F and -50 to 1300°C
• Resolution is 0.1° from -50.0 to 199.9° and 1° elsewhere, accuracy is ±0.3% plus 1°C
• Maximum only/HOLD
• Size: 2.75 x 5.25 x 1.25"; weight: 5.5 oz

Includes

Type K probe, 9 V battery, and NIST-traceable calibration certificate with data.

72-5300-22 Eagle Portable Monitor, LEL/Oxy/Br2 by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

3614-074 D-ReX PoI Gas Detector with 5 relays, Ozone (O3) MK473-10, 0 - 5 ppm by GfG

The D-ReX PoI's external sensor can be mounted in a location up to 4,000 feet / 1,200 meters away from the device and monitor toxic, combustible and corrosive gases as well as the oxygen concentration from there.

The remote sensor can be mounted directly onto pipe systems, gas cabinets and other hard-to-reach locations so that the gas detector itself can be mounted at eye level for easy access. This facilitates maintenance, inspections and operation.

With the optional saddle, it can also be used

Available Accessory:

• Mounting saddle
• Viton® (FKM) sealing for all saddle types
• M12 remote sensor cable, various sizes (3 to 100 ft / 1 to 30 m)
• Calibration cap for PoI
• Mounting brackets
• DIN rail

Features:

• 5x internal relays (form C, configurable)
• Smart sensors for more than 60 gases
• Hot-swappable smart sensor cartridge
• Tool-free maintenance
• Power-over-Ethernet (PoE) communication
• Web server for browser access
• Password-protected menu
• Interface: Analog outlet: 4 20 mA output; Digital: RS-485 (Modbus/RTU); 10/100 Mbit Ethernet (Modbus/TCP)
• Bright status and alarm LEDs
• Data logger to review sensor and alarm history
• Marked as FCC, CE, IC and UKCA