All Products

M-700004 Manning GM-JR Readout Module, feed-through configuration, stainless enclosure by Honeywell Analytics

This unique, practical gas monitor readout/alarm device offers a variety of configuration options for industrial refrigeration customers with their own computer control system, OEMs who want to incorporate gas sensing in their design and existing Honeywell Analytics customers who want remote indication other than at their main readout. It has an easily adjusted setpoint and relay output in either configuration, plus 4/20mA output in the "feed-through" design. With its own plug-in power supply, the GM-JR sensor combination provides an economical answer for local concentration level information and control capability.

The GM-JR standard configuration is a single, rugged, miniaturized board mounted inside the door of the enclosure, and a separate terminal board for the sensor and/or power cable connections. The 20-segment LED bar graph has a calibrated scale that is specified when ordered. Alarm trip adjustments are made easily at 5% increments. On power up or after momentary power loss, a one-minute power-up delay period allows the sensor to stabilize.

The unit continuously monitors the incoming 4/20 mA signal from the sensor. If the signal drops below 1.4 mA, the fault LED will illuminate and the alarm relay will trip. The alarm relay is always energized in its normal state, providing additional safety.

The GM-JR can be housed in its own 4" x 6" heavy-duty steel enclosure and operate as an "end of line" stand-alone readout/alarm unit or feed the sensor's 4/20 mA signal directly through to a PLC. It also can be mounted in the door of any sensor enclosure to incorporate both sensor and readout in the same 4" x 6" or 6" x 8" housing. Use #18/3 shielded cable (Belden #8770 or equal) for runs up to 1500' with most sensors.

Additional Features and Benefits:

• 20-segment calibrated bar graph
• Power-up delay
• Fail-safe design
• Easy trip setting
• Relay output is time delayed
• Downscale alarm configuration available for oxygen
• Rugged NEMA 1, gasketed steel enclosure
• Continuous fault monitoring
• Feed-through configuration allows remote readout capability while being powered from instrument cable (no remote power supply needed)

MX6-0000Q20B MX6 iBrid Multi-Gas Monitor, CO2 (IR), Lithium-ion Extended Range Battery, UL/CSA/ATEX/IECEx, No Pump, Czech by Industrial Scientific

The MX6 iBrid® is more than an intelligent hybrid of Industrial Scientific's best monitoring technologies—it's the most adaptable six-gas monitor on the market. With hundreds of possible sensor combinations, and a robust list of available configuration settings, the MX6 iBrid is ready to monitor oxygen, toxic and combustible gas, and volatile organic compounds (VOCs).

As your work changes, so can your MX6 iBrid. It uses five sensor slots to detect up to six gases. Each of those sensor slots accepts a variety of sensors, which means you can use the instrument with a PID sensor one day and an infrared sensor the next. What's more, settings allow you to adapt the instrument's behavior for your application. If you need to use a benzene PID response factor for one application, and butadiene for others, the familiar menu structure will allow you to quickly change settings.

The rugged MX6 iBrid carries our Guaranteed for Life™ warranty and is compatible with DSX™ Docking Stations. With a DSX Docking Station, maintenance is simplified and data becomes more than a spreadsheet filled with logged readings. Proactively manage your gas detection fleet—track trends, know when instrument maintenance will be required, and understand how your MX6 iBrid instruments are being used.

• 24 "Plug-and-Play" field-replaceable sensors including PID and Infrared options
• Up to 6 gases monitored simultaneously
• Simple, user-friendly, customizable, menu-driven navigation
• Five-way navigation button
• Durable, concussion-proof overmold
• Optional integral sampling pump with strong 30.5 meter (100 feet) sample draw
• Full-color graphic LCD is highly visible in a variety of lighting conditions
• Powerful, 95 dB audible alarm

*Please note we can only ship RKI products to customers within the United States

08080-99 Stainless Steel Bimetal Pocket Thermometer, 2" Dial, Poly Lens, 8" Stem, 0 to 550F, 5F Div by Digi-Sense

• Factory tested to three points with a ±1% accuracy
• Minimum immersion: liquids 2" (50 mm), gases 4" (100 mm)
• Hermetically sealed dial stops internal fogging
• Recalibrate using external adjustment nut
• 304 Stainless Steel dial case and stem
• Shock resistant

Includes

All thermometers come with a statement of test and a beaker clip.

2811-7072G-001 EC 28 Gas Transmitter with Carbon Monoxide (CO) Sensor, 2,000 ppm Range, No Display by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG's proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds - just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm - Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG's GMA controller.

The EC 28 DA provides additional bright alarm LEDs and a buzzer - avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor - sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

66-6194-99-W AirLink VOC Pro (11.7 ev PID) 0-1000 ppm Sensor/Transmitter with J-box with 900 MHz Radio by RKI Instruments

The AirLink VOC Pro Series Gas Detector is a versatile assembly that uses a PID sensor to detect a variety of gases. It is wire powered (12 to 35 VDC) with wireless communication to an RKI wireless controller and also has a 4-20 mA analog and RS-485 Modbus outputs are standard. Magnetic switches allow for non-intrusive calibration while in the field as well as full system settings and diagnostics.

Features

• PID sensor options: 10.0 eV lamp / 11.7 eV / 10.6 eV ppb / 10.6 eV ppm
• Wired power (3-Wire), 12 to 35 VDC operating voltage
• Output options: Wireless 900 MHz, or 2.4 GHz; 4-20mA (3-wire) analog; RS-485 modbus (4 wire)
• Operating temperature range -40°C to +54°C
• Graphical LCD with LED backlight
• 3 Push-button interface (ADD, MENU, SUB) with corresponding magnetic, non-intrusive switches
• 2 Individually configurable alarms
• 2 Front panel LED indicators (amber and red)
• 2 Optional fully programmable alarm relays (dry contacts)
• 1-Year warranty (see specifications)

Industry Applications

• Petrochemical plants, Refineries
• Water & wastewater treatment plants
• Pulp & paper mills
• Manufacturing facilities
• Chemical plants

*Please note we can only ship RKI products to customers within the United States

TX2-6B097 Tango TX2 Dual Gas Monitor, NH3, HCN, English by Industrial Scientific

• Protect workers, reduce false alarms, and spend less time managing your gas detector fleet with the Tango TX2.
• The Tango TX2 is the most accurate two-gas monitor featuring individual sensors that increase alarm accuracy.
• A two-year runtime and replaceable battery simplify gas detection management by eliminating the need for charging infrastructure.

0563 0409 400 Comfort Kit by Testo

Kits includes:

• Universal Airflow / IAQ Instrument
• Humidity temperature probe with Bluetooth
• Turbulence probe with cable
• Lux probe with cable
• USB power supply
• Software
• Pressure connection hose
• Service case for comfort measurement with testo 400

MX6-KJB34202 MX6 iBrid Multi-Gas Monitor, LEL (Pentane), CO/H2S, HCN, O2, NO2, Lithium-ion Extended Runtime battery (UL/CSA/ATEX/IECEX), Diffusion (no pump), French by Industrial Scientific

The MX6 iBrid® is more than an intelligent hybrid of Industrial Scientific's best monitoring technologies—it's the most adaptable six-gas monitor on the market. With hundreds of possible sensor combinations, and a robust list of available configuration settings, the MX6 iBrid is ready to monitor oxygen, toxic and combustible gas, and volatile organic compounds (VOCs).

As your work changes, so can your MX6 iBrid. It uses five sensor slots to detect up to six gases. Each of those sensor slots accepts a variety of sensors, which means you can use the instrument with a PID sensor one day and an infrared sensor the next. What's more, settings allow you to adapt the instrument's behavior for your application. If you need to use a benzene PID response factor for one application, and butadiene for others, the familiar menu structure will allow you to quickly change settings.

The rugged MX6 iBrid carries our Guaranteed for Life™ warranty and is compatible with DSX™ Docking Stations. With a DSX Docking Station, maintenance is simplified and data becomes more than a spreadsheet filled with logged readings. Proactively manage your gas detection fleet—track trends, know when instrument maintenance will be required, and understand how your MX6 iBrid instruments are being used.

• 24 "Plug-and-Play" field-replaceable sensors including PID and Infrared options
• Up to 6 gases monitored simultaneously
• Simple, user-friendly, customizable, menu-driven navigation
• Five-way navigation button
• Durable, concussion-proof overmold
• Optional integral sampling pump with strong 30.5 meter (100 feet) sample draw
• Full-color graphic LCD is highly visible in a variety of lighting conditions
• Powerful, 95 dB audible alarm

0554 1749 DIN rail mount power supply, 90-240 V AC / 24 V DC (2.5 A) by Testo

• For the external power supply
• 90 - 264 VAC / 24 VDC (2.5 A)
• Easy top-hat rail mounting

08068-23 Irreversible 5-Point Round Temperature Label, 450-500F/232-260C; 25/Pk by Digi-Sense

Labels are made up of a series of temperature-sensitive elements sealed between heat-resistant substrates with transparent windows. Each element changes color distinctly as its rated temperature is met or exceeded. The changes to the label are irreversible, providing a temperature history of the surface being monitored. The labels will not delaminate when removed, allowing them to be attached to an inspection report to serve as a permanent record. Ideal for use in the food, automotive, molding and metal working industries. Accuracy is ±1.8°F below 212°F and ±1°F above 212°F. Shelf life: 1 year after date of purchase.

Reliable proof that the product was maintained at the correct temperature

• Used as a quick inspection tool that the product is in usable condition during the shipping and receiving process
• Save time and money due to costly recalls
• Self-adhesive design

Part Number: X105325PM66