All Products

Personal Alarming Dosimeter and Rate Meter (Set in SI units) by SE International

The RADOS RAD-60 Personal Alarm Dosimeter is a precise and reliable instrument for ensuring the personal safety of the user. Ideally, the RAD-60 is used in everyday radiation monitoring, in stand-alone conditions. If your needs grow for a more sophisticated system, the versatile RAD-60 can also be integrated into an Access Control System. The RAD-60 can be switched into System Mode, for the purpose of tracking Personnel Dose records and generating compliance reports.

The design includes state-of-the-art technology with built in memory for retrieving dose, even during power-down. It eliminates outside interference from shock and RF. The RAD-60 is easily programmed by the user, has a digital display, and operates with a single AAA alkaline battery.

With the push of a button, you can turn the unit on/off, change the digital display to read dose or dose rate, select from several dose and dose rate alarm levels, turn the chirp functionon/off, reset the integrated dose, and perform battery tests. The large digital display gives instant dose or dose rate readings and the audible alarm is loud (>85dba)

The Access Control System is a combination of the following two accessories:

ADR-1 Configuration Kit

The ACS Express Software

08080-95 Stainless Steel Bimetal Pocket Thermometer, 1.75" Dial, Glass Lens, 8" Stem, 50 to 550F, 5F Div by Digi-Sense

• Factory tested to three points with a ±1% accuracy
• Minimum immersion: liquids 2" (50 mm), gases 4" (100 mm)
• Hermetically sealed dial stops internal fogging
• Recalibrate using external adjustment nut
• 304 Stainless Steel dial case and stem
• Shock resistant

Includes

All thermometers come with a statement of test and a beaker clip.

08139-01 TI.30 4 Back-Con Bimetal Thermometer, Dial 3", 4" L/0-250F/-20-120C by Digi-Sense

Accuracy is ±1% full-scale when stem is immersed 2" in liquids or 4" in gases (immerse models with a 2.5" stem length 2" in gases). Measured stem length from the top of the threads to the bottom tip of the stem. Stem dia is 0.25"; threaded connection is 1/2" NPT(M). All thermometers meet or exceed ASME B40.3 standards. Maximum environmental temperature for glass lens thermometers is 500°F (148°C).

Key Features

• Greater temperature range
• Anti-parallax dial for accurate readings
• Hermetically sealed per ASME B40.3 standard to prevent fogging and protect against tough environments
• Rugged 304 stainless steel construction with a clear glass lens
• Recalibrate using the external reset screw

*Please note we can only ship RKI products to customers within the United States

276141 Colorimeter (Lovibond), MD100: Molybdate, 0.3-40 mg/L Mo by AquaPhoenix

The MD 100 range of Photometers are portable handheld instruments. A simple button layout, robust waterproof design and large backlit display make the MD100 easy to use and ideal for testing in the field, laboratory or plant room. The units supply accurate, reproducible results using high quality interference filters with long-life LEDs as a light source. Tests are conducted using Lovibond® tablet or powder pack reagents which give long-term stability and a long shelf life. Kits come complete with everything needed for testing: Instrument, reagents, batteries, instructions and case.

*Please note we can only ship RKI products to customers within the United States

SPXCDUSNO1 Sensepoint XCD Gas Detector, 4 to 20 mA output, UL/c-UL/INMETRO, 2 x 3/4" NPT entries, painted 316SS, includes oxygen EC sensor cartridge 0 to 25% v/v, includes nylon weather protection by Honeywell Analytics

Honeywell can trace its company roots back nearly 125 years. What started off as a company dedicated to heating technologies has blossomed into an enterprise dedicated to a variety ofsafety, security, and energy solutions. By integrating the most advanced technologies with intuitive designs, Honeywell has established itself as an industry leader in workplace safety products and gas detection solutions. The company s commitment to advancement and growth help pave the way for innovation and creativity in design. The Sensepoint XCD detection system is the epitome of product advancement. Building on 125 years of industry experience, Honeywell has introduced a comprehensive monitoring system that is reliable, dependable, and state of the art.

Sensepoint XCD

With the Sensepoint XCD detection system, Honeywell provides easy to use, low maintenance sensory devices for monitoring explosive atmospheric conditions in a variety of industrial settings. The Sensepoint XCD system monitors for explosive oxygen gas, toxic gas, and flammable conditions and constantly relays status through transmitters utilizing a simply traffic light LCD system which can be easily seen and understood from a distance.

Superb Versatility

The Sensepoint XCD system provides a catch all-detection system which has worldwide industry approvals and is compliant with all relevant standards. Suited for indoor use as well as the harshest outdoor conditions, the Sensepoint XCD systemis a versatile product for use in any potentially dangerous industrial atmosphere. The unit is available in both stainless steel and aluminum housing options, both of which are resistant to explosions. The XCD transmitter systems are for three separate environmental conditions (flammable, toxic, and oxygen). Each transmitter has a variety of sensors available for use. Each transmitter will automatically recognize the sensor within its category. The plug-in design of the sensors allows users to simply plug the sensor into the transmitter. The transmitter will automatically adjust and configure for the appropriate sensor settings.

Simplicity in Design

The Sensepoint XCD system is easy to install with a simple plug-in design, a built-in mounting system, and comes equipped with versatile wiring receptions to limit compatibility issues for the end user. Once installed, the system utilizes a traffic light type display of green for normal, yellow for warning, and red to alert an atmospheric issue. The maintenance of the system is just as user-friendly with routine maintenance easy and ergonomic enough to be done by one person. The system is also simple enough that it can be used and maintained with little training.

Cost Savings

The Sensepoint XCD system provides a business with cost reductions in both hardware and staffing. The versatile usage and low maintenance of the system reduces the resources needed to monitor conditions and allows personnel to focus on their tasks at hand. The system also provides personnel, and any other parties in the area, peace of mind that their conditions are being constantly monitored for danger and relayed in a way that anyone can detect and bring awareness to dangerous conditions.

CP-5001C-GRY Cap, Gray (for BO-5001B-P, BO-5002B-P, BO-5003B-P) by AquaPhoenix

Screw cap made of polypropylene. Cap is ribbed to ensure easy handling.

8328422 X-am 3500 Multi-Gas Detector, Ex, O2, CO LC, NO2 (without charging equipment) by Draeger

The Draeger X-am® 3500 was especially designed for clearance measurements. The 1 to 4 gas detector reliably detects flammable gases and vapours as well as O₂, CO, H₂S, NO₂ and SO₂. The innovative signalling design and extensive range of accessories ensure optimum safety and easy handling.

Specially designed for use with a pump, optimised for clearance measurement

The Draeger X-am 3500 is equipped with a very powerful pump. It can be connected with hoses of up to 45 metres in length. A pump adapter makes it easy to switch between diffusion and pump mode at any time. This means the pump is only operated when you actually need it. That saves energy, reduces wear and tear, and thereby extends the lifespan of the pump.

The performance of selected sensors has been verified by an external approval body within the scope of the measurement performance approval (EN 60079-29-1), for combustible gases and vapours for methane, propane and n-nonane, among others.

Handy and durable, the Draeger X-am 3500 is intuitive to operate single-handedly using three function keys. The easy-to-read colour display clearly lays out all the information for you. Thanks to its compact and robust construction, the device can withstand even the harshest conditions.

Clear signalling design

The signal system of the Draeger X-am 3500 is based on a clear colour code, in accordance with the requirements of the EN 60079-29-1, EN 45544-1 and EN 50104:

• Red light = gas alarm
• Yellow light = device-related alarm, e.g. low battery
• Green light = device is ready for use

The green glow of the D-Light allows you to see from a distance whether the device has been properly tested and is ready for use.

In case of an alarm, the X-am 3500 alerts you with colourful alarm LEDs, a loud horn (100 dB(A) at a distance of 30 cm), and clearly palpable vibration. Optionally, four preset hazard symbols are available for the display which explicitly indicate the presence of explosive or toxic gas hazards, for example. This allows the user to easily recognise the type of hazard based purely on the symbol displayed.

Economical Fleet Management

Bumptest and calibration are carried out simply and quickly using the Draeger X-dock® calibrating station. Its low test gas consumption keeps operating costs to a minimum.

Its reporting function and numerous other useful features make the X-dock Manager PC software a smart addition to any fleet management operation. To identify the devices in the fleet, you can either use tried and tested barcodes or an integrated RFID transponder.

Inductive charging protects against wear and tear

The X-am 3500 features inductive charging. This makes it easier to operate and increases the lifespan of the device. Issues like corrosion and contact problems in the charging cradle are a thing of the past. You can charge (outside of explosion-hazard zones) and measure at once, e.g, when in use inside vehicles or on machinery. The charging cradle can connect with one another, taking up minimal space, and are compatible with existing Draeger X-am® series cradles.

*Please note we can only ship RKI products to customers within the United States

66-5A66-2K-R Air Alert Ambient Air Hazardous Gas Detector, sulfur hexafluoride, SF6, AC powered, with relays by RKI Instruments

The RKI Air Alert series ambient air toxic gas detector is a versatile assembly that uses an electrochemical, infrared or PID sensor element to detect a variety of gases. Wire powered (12 to 35 VDC) with 4-20 mA analog and RS-485 Modbus outputs. Magnetic switches allow for non-intrusive calibration while in the field as well as full system settings and diagnostics.

Features

• Electrochemical, Infrared, or PID sensor element
• Wire powered (3-wire), 12-35 VDC operating voltage, optional AC power supply
• Operating temperature range of -40°C to +70°C
• 3 Push-button interface (ADD, MENU, SUB) with 3 corresponding magnetic, non-intrusive switches
• 2 Dry contact relays (optional)
• Graphical LCD with LED backlight
• Output options: 4-20mA (3-wire) analog, RS-485 Modbus, optional 900 MHz or 2.4 GHz radio
• Optional 3 color LED perimeter and audible alarm
• 1-Year warranty

Industry Applications

• Petrochemical plants, Refineries
• Water & wastewater treatment plants
• Pulp & paper mills
• Manufacturing facilities
• Chemical plants

*Please note we can only ship RKI products to customers within the United States