All Products

Part Number: 34L-422

2106B1413 Sensepoint Hazardous Area Approved Gas Detector, NH3 0-50 ppm Toxic Sensor M20 by Honeywell Analytics

The Sensepoint range of flammable, toxic and Oxygen gas detectors offer users a high quality, low cost solution to their industrial gas monitoring needs. Installation in potentially explosive atmospheres is made by the use of a suitable Ex d or Ex e approved junction box. The industry standard outputs from Sensepoint are connected to either a choice of Honeywell Analytics' controllers or 3rd party DCS/ PLC systems. Both flammable and toxic versions are certified to the latest ATEX/IECEx safety and performance standards.

The flammable detector is available in either % LEL or PPM detection range versions and provides an industry standard mV bridge output. Typical life expectancy is greater than 5 years, after which the detector is simply replaced with a new one.

The toxic detectors are supplied pre calibrated for easy installation and provide an industry standard 2 wire 4-20mA loop output. User connections are Ex d, while front end Intrinsic Safety (IS) design allows for easy exchange of the replaceable sensor while powered. IS design also removes the need for a sinter enabling very fast speed of response and detection of 'sticky' gases such as Chlorine and Ammonia.

Sensepoint has proven its suitability across a wide range of demanding applications by delivering high performance and reliability at an affordable cost.

Fit For Purpose

• Flammable, toxic and Oxygen versions available
• High performance, low cost
• Suitable for new and retro fit applications

Proven Sensor Technology

• Surecell™ electrochemical sensors
• Poison resistant catalytic bead
• Fast and reliable
• Typical 2 to 5 years operational life

ATEX/IECEx Certified

• Complies with the latest standards
• Hazardous area approval and performance
• IP65/67 for use in harsh environments

Easy to Use

• Factory set operation
• Simple to replace
• Minimal training required

Range of Accessories

• Weatherproof cap
• Flow adaptor
• Duct mounting kit
• Collecting cone

GS-CS-B-069-G Gasman Single Gas Monitor, 0-500ppm Carbon Monoxide (H2 filtered), Non Rechargable Battery (single use), Spanish Safe Area only by Crowcon

For over 40 years, Crowcon Detection Instruments has produced state of the art gas detection devices for personal and industrial use. Building upon their reputation for reliable and innovative gas monitoring products, Crowcon introduces the Gasman personal gas monitor. Its lightweight and compact design is convenient for jobsites where workers need not be weighed down by excessive bulk and equipment. The unit conveniently clips to a pocket or helmet and operates continuously.

The Gasman personal gas monitor has numerous convenient features such as:

• One button technology
• Backlit LCD display
• Durable polycarbonate casing
• Quick response triple alert system
• Compact and lightweight design

Easy to Use

The Gasman s true one button technology is an ideal and simple design. The large glove friendly button is mounted on the front of the unit for easy access and controls all of the unit s programmable features. Also on the front, the Gasman s easy to read backlit LCD screen indicates gas readings and the battery status. The simple screen provides a clear indication of the unit s operation status. It will also alert the user 30 days in advance of when a calibration test is due. With a simple and intuitive design, Crowcon has produced a gas detector that reduces the complexities of workplace safety, and ensures workers in a straightforward manner that their equipment is on and operational.

Triple Alarm System

This portable single gas detection system features a triple alarm system that is sure to alert the user and anyone in the vicinity. The visible alarm utilizes a dual red and blue flashing LED light, and the unit houses an internal vibrating alert system. These two indicators allow for visual recognition in loud environments and working conditions. The alarm system also features a programmable audible alarm at 95 decibels. The unit is capable of a variety of alarm tones, and users can select which tone may be best for the individual workplace setting. The triple alarm system with multiple sensory indicators is sure to be noticed in almost any work environment.

Specifications

The Gasman single gas monitor is lightweight and compact, weighing less than 135 grams and with dimensions of 90 x 48 x 24 mm. The unit is available with a wide variety of gas sensors which feature various detection and alarm levels. The unit also features a quick response time of 20 seconds for flammable and toxic gases or 10 seconds for oxygen. Its datalogging feature has approximately 900 hours of storage and all events are time stamped. The battery life for this unit is incredible with 12 hours of runtime on a Rechargeable battery battery or up to 2 years on a non-Rechargeable battery.

72-FA-A-A10-50 GX-Force Portable 4 Gas Monitor, LEL / O2 / H2S / CO Unit with Li-Ion Battery Pack, and Padded Case by RKI Instruments

With the GX-Force, you have multiple tools in one instrument. Having 2 operating modes, the GX-Force can be used for confined space, safety monitoring in its Normal Operating mode. A Leak Check mode is the solution for all leak investigations.

The GX-Force is RKI's smallest personal 1-4 gas monitor with a strong built-in sample pump capable of a 100' sampling range. Weighing only 9.8 ounces, the GX-Force can monitor the standard confined space gases (LEL combustibles, Oxygen content, Carbon Monoxide, and Hydrogen Sulfide). Built around high-quality micro-sensor technology, which are compatible with the GX-3R, GX-3R Pro, 04 Series, and Gaswatch 3 instruments.

The GX-Force's large LCD display shows all gas readings, battery level, current time, and will automatically backlight in alarm conditions. Standard alarm types include vibration, visual, and audible alarms, which can be set to latching or non-latching. Controlled by a microprocessor, the GX-Force continuously checks itself for sensor connections, low battery, circuit trouble, low flow, and calibration errors. The GX-Force operates 30 hours on a Li-ion battery.

Calibration and bump test intervals and reminders are user adjustable and can be set to either go into alarm or to lock the user out of normal measurement mode once a calibration period has expired. Calibrations can be performed automatically or individually in single calibration mode. Calibration can be done individually or in a group.

Features

• 2 Operating modes: Normal and Leak Check
• Internal sample pump with 100' sample range
• 30 hours of operation (Lithium-ion battery)
• Easy to grip lightweight design: 2.5" W x 6.81" H x 1.85" D, 9.87 ounces
• Water and dust resistant design, IP67
• Field replaceable sensors & filters
• Impact resistant body
• Intrinsically safe
• Large LCD Auto-backlit display
• 3 Year warranty

Applications

• Personal monitoring
• Confined spaces
• Refineries/petrochemical
• Utilities
• Oil and Gas
• Water/wastewater
• Fire services
• Construction

*Please note we can only ship RKI products to customers within the United States

QL-110 Test Strips: Lo Ion Quat, 0-100 ppm, roll by AquaPhoenix

Simple and cost effective method of measuring the concentration of quaternary concentrations. Color matches at 0-10-25-50-100ppm

Each kit contains one 15-foot roll of test paper, matching color chart, and two sample tubes with caps. In addition there is one extra roll of test paper and a laminated color chart. Provides for approximately 100 tests.

*Please note we can only ship RKI products to customers within the United States

8326333 Pac 6500 O2 by Draeger

The robust Draeger Pac® 6500 is your reliable companion under tough conditions. The personal single-gas detection device measures CO, H₂S, SO₂ or O₂ quickly and precisely. Quick sensor response times and a replaceable battery also ensure safety.

Strong performance for maximum safety

You can rely on the Draeger Pac 6500: the personal single-gas detection device warns against hazardous concentrations of carbon monoxide, hydrogen sulfide, sulfide dioxide or oxygen with precision and reliability.

Powerful sensors with a very low t-90 response time ensure quick reactions. The Pac 6500 is versatile thanks to its wide measurement range. For example, the CO sensor measures concentrations from 1 to 1,999 ppm, and the H₂S sensor from 0.4 to 100 ppm.

Easy handling thanks to clear user guidance

The D-Light indicates whether functionality of the device has been tested and whether it is ready to use. The housing is also designed with your safety in mind: each sensor variant of the Draeger Pac 6500 features clearly visible color coding, thereby minimizing the chance of mistakes.

Robust design – even for the toughest conditions

The Pac 6500 is easily handled in even extreme conditions. Depending on the sensor, temperatures from -40 °C to 55 °C and air pressures between 700 and 1,300 mbar can be tolerated.

A membrane filter protects the sensor from foreign matter such as dust and liquids. The shock-proof, chemical-resistant housing meets the requirements specified in the IP68 standard rating.

User-friendly display with all important information

The large display clearly indicates the respective gas concentration. Other important information, such as the battery capacity, is also displayed. The bright backlighting ensures that all values are clearly legible in the dark.

360° alarm with various functions

If the Draeger Pac 6500 measures hazardous gas concentrations, it sets off an audible, visual and perceptible vibrating alarm. Two bright, flashing LEDs on the top and bottom of the device ensure that the alarm is easily visible from all sides. The acoustic signal reaches a volume of 90 dB. The display can show the peak concentration measured at any given moment. Earlier alarms registered can also be retrieved at a later time, even if they have been acknowledged.

The Pac 6500 with oxygen sensor has two additional alarm thresholds in addition to the standard alarm threshold settings. This provides an additional level of safety as a pre-alarm, in addition to the main alarm, can be set for both oxygen enriched and oxygen deficient atmospheres.

Data logger and event logger for analyses and reports

The Draeger Pac 6500 logs concentrations and events along with the date and time. The data can be loaded on a PC via an interface and processed further there.

Economical operating costs

All versions of the Pac 6500 are equipped with extremely durable DraegerSensors and a powerful battery.

The Pac 6500 is protected against water, dust and other foreign bodies by a special membrane filter. When the filter becomes heavily soiled in use, you can quickly and easily replace it yourself. The device is then ready to use again right away.

Fast function test saves time and money

Function tests and calibrations can be carried in the Draeger X-dock® calibration station. The automatic bump tests in the X-dock are a cost-efficient and convenient solution thanks to the short test duration and the extremely low consumption of test gas. The Pac 6500 is simply placed in the bump test station and automatically selects the correct setting.

Part Number: CG2M100103

72-RH-C GX-3R 2-Gas Confined Space Monitor, LEL / H2S with Li-Ion Battery Pack with 100-240 VAC Charger by RKI Instruments

OSHA defines the breathing zone as a ten inch radius around the worker's nose and mouth, and requires that worker exposure monitoring air samples be collected in the breathing zone. Air sampling filters may be attached to the collar or lapel. Traditionally this means only a single gas monitor would be small enough for a worker to practically wear a gas monitor 'In the breathing zone'. Now there is a 4 gas monitor smaller than many single gas monitors.

The GX-3R is the worlds smallest 4 gas monitor weighing only 3.52 ounces and can comfortably be clipped within a worker's breathing zone (2.2" W x 2.55" H x 1.02" D). It simultaneously monitors and displays LEL combustibles, O₂, CO (Hydrogen compensated CO also available), and H₂S.

The GX-3R represents the latest evolution of gas detection technology utilizing a new generation of micro sensors. The LEL sensor has a unique design with two active filaments in one sensor to increase it's resistance to silicone poisoning. If one filament gets poisoned the second filament takes over. The new O₂ sensor is electrochemical with a 3 to 5 year life span. H₂S and CO are now available in a combo micro sensor.

Safety supervisors will appreciate the non-compliance indicator. The instrument flashes it's 3 LED lights every 30 seconds in the following conditions; if the instrument has not been bump tested, or if calibration is due, or if there was a gas alarm event. The 3 LED lights will continue to flash once every 30 seconds until the non-compliance condition has been resolved. The 30 second interval is adjustable.

Features

• Smallest & lightest 4 gas monitor: 2.2" W x 2.55" H x 1.02" D, 3.52 ounces
• Simultaneous detection of 4 gases: LEL, O2, H2S & CO; H2 Compensated CO sensor available
• Simple 2-button operation
• Non-Compliance Indicator
• Alarms: audible, visual, & vibration
• 3 user adjustable alarm levels
• Impact resistant body with removable rubber boot
• Large LCD Auto-backlit display
• 25 hours of operation (Lithium-ion battery)
• Field replaceable sensors & filters
• Water and dust resistant design, IP66/68
• Stealth mode for law enforcement
• 3 Year warranty

Applications

• Personal monitoring
• Confined spaces
• Refineries/petrochemical
• Utilities
• Oil and Gas
• Water/wastewater
• Fire services
• Construction

*Please note we can only ship RKI products to customers within the United States

791JC Panel Mount Digital Temperature Transmitter with 4- 20 mA Current Output, Type J by Jenco

Panel mount digital temperature transmitter with 4- 20 mA current output that allows the 791 to drive any loop powered process indicator or recorder. Current output has expanded or normal switch for user adjustable center point and span control for temperature to 4-20 mA output and features a LCD display & 1/8 DIN Aluminum case. Types. J, K, T, 3-wire Pt-100 RTD, specify °C or °F. Ambient range 0 to 40°C. 115 / 230V AC operation.

• All solid state design
• Low power consumption ,reduced internal heating ,increased reliability
• High 50/60 hz noise rejection
• Heat cycled 100 hours before shipment
• Available for various thermocouple and rtd calibrations
• Easy to install
• Aluminum 1/8 DIN housing
• Isolated 4 to 20 mA output over span in nor mode
• 115VAC /230VAC operations

VN00194 PSS 5000/7000, 2216/30, CGA, SR, LW, w/B by Draeger

Effective firefighting requires trusted breathing protection in the harshest environments. The Draeger PSS® 5000 provides the budget-conscious fire department with an ergonomically advanced SCBA. With a wide range of features – such as bi-lateral hose routing and cylinder Quick Connection – the PSS® 5000 meets the needs for today's complex fire grounds.

Proven technology combines comfort with performance

The Draeger PSS 5000 SCBA is designed to withstand the high wear and tear that firefighters face daily – while providing an enhanced level of comfort and functionality. Made of tough chloroprene rubber material and Aramid-blend webbing, the PSS 5000 harness is ideally suited for extended wear and frequent use.

The flexible harness connects to a lightweight, stable back plate, while the waist belt pivots to reduce pressure on the wearer.

Integrated systems reduce risk and increase versatility

To minimize the risk of damage or snagging, the Draeger Sentinel 7000 electronic system and air-supply hoses are integrated into the backplate. To further streamline and reduce snag hazards, the lung-demand valve (LDV) - and Draeger Sentinel hoses are routed over the shoulders. Conventional waist-mounted hoses can also be fitted to the carrying system, making the Draeger PSS 5000 one of the most versatile SCBA systems available.

Easy maintenance to lower cost of ownership

The following features keep Draeger PSS 5000 downtime and maintenance costs to a minimum:

• Innovative slide-and-lock mechanism for fast and easy harness assembly and disassembly
• Harness detaches from the backplate without the use of tools
• First stage reducer snap-fit connection allows pneumatics to be fitted or removed quickly and easily
• Hose clips push in and out to allow swift removal of hoses from the harness pads for cleaning
• Chemical-resistant harness and waist belt design prevent excessive water absorption and reduce cleaning and drying time
• Standard AA batteries, no manufacturer-required overhaul, and few replacement parts contribute to a lower total cost of ownership over the life of the SCBA

Draeger Sentinel 7000 Real-time monitoring

The Sentinel 7000 electronic monitoring system provides options to satisfy the needs of any fire department. Incorporating a centralized power supply and pressure sensor module within the backplate, the robust system combines maximum component protection with balanced weight distribution for reduced physical stress.

Housed in impact-resistant, water-resistant casings, the Sentinel 7000 demonstrates excellent reliability on the fire ground.

An electronic gauge provides real-time monitoring of essential information, including:

• A personal alert safety system (PASS) device
• Intuitive push-button operation for ease of use
• Configurable settings to suit individual preferences
• Data logging for improved post-incident analysis
• Accurate, continuously updated digital display of pressure and time to EOSTI activation (time based on dynamic breathing rate)
• Battery status display
• 360° visual and audible alarms triggered when the PASS is activated
• Automatic self-tests and system tests

XNX-AMSI-RNNNN XNX Universal Transmitter, ATEX M25 SS RLY FOR OPT/XL SNSR by Honeywell Analytics

XNX Universal Transmitter, ATEX M25 AL FF HRT FOR TOX/O2 SNSRThe XNX Universal Transmitter, now with HART EDDL, marks a new turn in gas detection from Honeywell Analytics. It supports the widest range of sensors on a common platform and offers a modular choice of inputs and outputs.

XNX is designed for flexible integration, simple installation, user-friendly operation and straight-forward maintenance. It is ideal for use with a range of gas monitoring controllers or industry standard PLCs. The introduction of our HART Enhanced Device Descriptor Language (EDDL) software provides users with an at-a-glance indication of the health of their gas detectors in the field.

Bringing together the best solutions in gas detection

Electrochemical

• Proven electrochemical sensing technology
• Surecell™ electrochemical cells are ideal for hot and humid environments
• Long life sensing cells (typical >2 years)
• Patented 'Reflex' sensing element verification diagnostics
• Sensor recognition software auto configures transmitter
• Plug and play factory configured sensors
• Intrinsically safe sensor connection permits hot swap, reducing down time

Catalytic Bead

• Supports Honeywell Analytics 705, 705HT, Sensepoint, Sensepoint HT and MPD sensors
• Fast response to wide range of hydrocarbons and flammables

Infrared (Open Path IR, Point IR, IR Cell)

• Supports Honeywell Analytics Searchline Excel, Searchpoint Optima Plus
• Failsafe operation
• Fast speed of response
• Reduced routine maintenance
• Immune to catalytic poisons
• Long operating life
• Works in inert atmospheres

High performance

• Flammable gas detection 0 to 100% LFL/LEL
• Point IR with heated optics provides immunity to poisoning and no hidden faults
• Open-path IR flammable gas detection in LEL-m measurement
• Electrochemical cell offers toxic gas detection in ppm
• IR cell provides CO₂ and combustible gas monitoring
• Robust and reliable operation in explosive areas and harsh environments

Flexible Operation

• 3 versions - supports (Catalytic Bead and IR Cell), Electrochemical Cell and IR (point and open-path) gas detection
• Multi-Purpose Detector (MPD) with field serviceable mV, Catalytic bead and IR Cell capability
• 4-20mA with HART® as standard
• HART Enhanced Device Description Language (EDDL) software*
• Multiple communications options include up to 3 relays, MODBUS® and FOUNDATION® H1 Fieldbus
• Optional local IS port for handheld HART configurator

Easy to Use

• Large, backlit, easy-to-view LCD display offers multisensory indicators (visual icons, colored buttons, text, etc.) to display gas and sensor readings
• User interface supported by 8 selectable languages (English, Spanish, German, Italian, Portuguese, French, Russian, Chinese)
• Self-test and fault indication features
• Non-intrusive, one-man operation
• Quick calibration with auto-inhibit

Easy to Install

• 3 or 4 wire operation, source, sink or isolated
• Simple plug-in sensors and replaceable cells
• NEMA 4X IP66 rated for rugged indoor/outdoor use
• Five conduit entries for ease of installation

Cost Effective

• Minimal training required
• One-man operation
• Plug-in sensor replacement
• All necessary accessories included

72-PPB-E GX-3R Pro 2 Gas Personal Monitor - O2 - CO2, 10% volume, IR - Li-Ion Battery Pack Only (No Charger) by RKI Instruments

The GX-3R Pro is the world's smallest 5-gas monitor weighing only 4.58 ounces and fits in the palm of your hand (2.9" W x 2.6" H x 1.06" D). It simultaneously monitors and displays 5 different gases. In addition to monitoring standard confined space gases, LEL, O₂, CO, & H₂S, the GX-3R Pro has a 5th channel where you can add infrared or toxic sensors. Two of the four sensor slots have interchangeable sensors providing flexible configurations, which can easily be changed in the field.

The GX-3R Pro comes equipped with Bluetooth wireless communication, man-down alarm, the choice of alkaline or rechargeable power supply, and a 3 year warranty. The Lithium-ion battery pack will operate for 25 hours and will fully charge in 3 hours.

The GX-3R Pro utilizes Bluetooth communication to display direct gas readings from the instrument to a phone app, which is available free on either iOS or Android phones. Automatic notifications can be programmed to send text or email messages, if there is an alarm event from the GX-3R Pro.

Safety supervisors will appreciate the non-compliance indicator. The instrument flashes it's 3 LED lights every 30 seconds in the following conditions; if the instrument has not been bump tested, or if calibration is due, or if there was a gas alarm event. The 3 LED lights will continue to flash once every 30 seconds until the non-compliance condition has been resolved. The 30 second interval is adjustable.

Features

• Smallest & lightest 5 gas monitor: 2.9" W x 2.6" H x 1.06" D , 4.58 ounces
• Simultaneous detection of 5 gases: LEL, O₂, H₂S, CO, and other optional sensors; H₂ Compensated CO sensor available
• Simple 2-button operation
• Bluetooth communication with iOS & Android App
• Non-Compliance Indicator
• 3 user adjustable alarm levels
• Panic Alarm - Tap instrument twice
• Man Down Alarm
• Impact resistant body
• Large full dot, auto-backlit display with auto-rotation
• Stealth mode for law enforcement
• Field replaceable sensors & filters
• Water and dust resistant design, IP66/68
• 3 Year warranty

Applications

• Personal monitoring
• Confined spaces
• Refineries/petrochemical
• Utilities
• Oil and Gas
• Water/wastewater
• Fire services
• Construction

*Please note we can only ship RKI products to customers within the United States

Part Number: X1005100PA

18100060-5A Gasbadge Pro Single Gas Monitor, SO2, AUS by Industrial Scientific

Built to Industrial Scientific's highest quality and reliability standards, GasBadge® Pro provides a lifetime of gas hazard protection with more features than any other single gas monitor available. Interchangeable "smart" sensors enable the GasBadge Pro to be quickly adapted to monitor unsafe levels of oxygen or any one of the following toxic gases: carbon monoxide, hydrogen sulfide, nitrogen dioxide, sulfur dioxide, chlorine, chlorine dioxide, phosphine, ammonia, hydrogen cyanide and hydrogen. GasBadge Pro communicates directly via an infrared interface to optional accessories like the DSX Docking Station, Datalink and infrared printer to further simplify and automate calibration, function (bump) testing and data downloading. Standard STEL and TWA readings, and datalogging of up to one year of survey data are featured along with an event-logger that records the past 15 alarm events.

Housed in a rugged enclosure, the monitor is immune to RF, water resistant and extremely durable. A protective concussion-proof overmold protects the unit from extreme abuse in a variety of harsh industrial environments. It's simple and intuitive four-button navigation allows easy access to setup, operation and calibration functions.

• Interchangeable "smart" sensors monitor oxygen or any one of many toxic gases
• One-year data logging capacity (minimum)
• Standard STEL and TWA
• iNet® ready and DSX™ Docking Station compatible

TDS5687/P Conductivity Solution, 5687ppm/7000uS, 1Pt by Sensorex

TDS/Conductivity instruments and sensors must be calibrated together. For a single-point calibration, select the one solution that approximates the expected conductivity or ppm level of total salts. Mixed Salt standards are the most frequently used in the field to sample naturally occurring water sources, boiler feed water, or cooling tower water. Typical river water, well water, or lake water sample will contain a mixture of several different salts. Sensorex Mixed Salt standards simulate a "Natural" mixture of common salt compounds found in these sources. Sodium sulfate, sodium bicarbonate, and sodium chloride salts are blended to provide a representative value. There are certain applications where Single Salt Solutions are preferred. NaCl Solution is routinely used to calibrate instruments measuring Sea Water or brackish water samples. Reagent grade salt and high resistivity DI water is compounded for accurate results. KCI Single Salt Solution may be used with conductivity meters that read directly in Siemens or Ohms. KCI (potassium chloride) is established as an international calibration standard for conductivity measurement. Choose the conductivity calibration solution that is right for your application. CA Residents: Prop 65 WARNING(S)

XNX-AMSV-MNCB1 XNX Universal Transmitter, ATEX M25 SS MDBS MPD CAT LEL by Honeywell Analytics

XNX Universal Transmitter, ATEX M25 AL FF HRT FOR TOX/O2 SNSRThe XNX Universal Transmitter, now with HART EDDL, marks a new turn in gas detection from Honeywell Analytics. It supports the widest range of sensors on a common platform and offers a modular choice of inputs and outputs.

XNX is designed for flexible integration, simple installation, user-friendly operation and straight-forward maintenance. It is ideal for use with a range of gas monitoring controllers or industry standard PLCs. The introduction of our HART Enhanced Device Descriptor Language (EDDL) software provides users with an at-a-glance indication of the health of their gas detectors in the field.

Bringing together the best solutions in gas detection

Electrochemical

• Proven electrochemical sensing technology
• Surecell™ electrochemical cells are ideal for hot and humid environments
• Long life sensing cells (typical >2 years)
• Patented 'Reflex' sensing element verification diagnostics
• Sensor recognition software auto configures transmitter
• Plug and play factory configured sensors
• Intrinsically safe sensor connection permits hot swap, reducing down time

Catalytic Bead

• Supports Honeywell Analytics 705, 705HT, Sensepoint, Sensepoint HT and MPD sensors
• Fast response to wide range of hydrocarbons and flammables

Infrared (Open Path IR, Point IR, IR Cell)

• Supports Honeywell Analytics Searchline Excel, Searchpoint Optima Plus
• Failsafe operation
• Fast speed of response
• Reduced routine maintenance
• Immune to catalytic poisons
• Long operating life
• Works in inert atmospheres

High performance

• Flammable gas detection 0 to 100% LFL/LEL
• Point IR with heated optics provides immunity to poisoning and no hidden faults
• Open-path IR flammable gas detection in LEL-m measurement
• Electrochemical cell offers toxic gas detection in ppm
• IR cell provides CO₂ and combustible gas monitoring
• Robust and reliable operation in explosive areas and harsh environments

Flexible Operation

• 3 versions - supports (Catalytic Bead and IR Cell), Electrochemical Cell and IR (point and open-path) gas detection
• Multi-Purpose Detector (MPD) with field serviceable mV, Catalytic bead and IR Cell capability
• 4-20mA with HART® as standard
• HART Enhanced Device Description Language (EDDL) software*
• Multiple communications options include up to 3 relays, MODBUS® and FOUNDATION® H1 Fieldbus
• Optional local IS port for handheld HART configurator

Easy to Use

• Large, backlit, easy-to-view LCD display offers multisensory indicators (visual icons, colored buttons, text, etc.) to display gas and sensor readings
• User interface supported by 8 selectable languages (English, Spanish, German, Italian, Portuguese, French, Russian, Chinese)
• Self-test and fault indication features
• Non-intrusive, one-man operation
• Quick calibration with auto-inhibit

Easy to Install

• 3 or 4 wire operation, source, sink or isolated
• Simple plug-in sensors and replaceable cells
• NEMA 4X IP66 rated for rugged indoor/outdoor use
• Five conduit entries for ease of installation

Cost Effective

• Minimal training required
• One-man operation
• Plug-in sensor replacement
• All necessary accessories included

9429100 Chlorine, Total Chemkey Reagents by AquaPhoenix

Total Chlorine Chemkeys, range 0.04 - 10 mg/L Cl2. For SL1000 Portable Parallel Analyzer (PPA). Box of 25.

USEPA accepted for reporting in drinking water analysis using Hach Method 10260.

72-5200-20 Eagle Portable Monitor, Oxy/F2, no probe by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States