All Products

020-0040-020 Confined Space Kit 2 by RAE Systems

Confined Space Kit 1 includes

• Four-gas mix in a 34L cylinder (50% LEL, 18% O2, 10 ppm Hydrogen Sulfide, 50 ppm Carbon Monoxide)
• Regulator and tubing

Part Number: 10L-442

72-RA-C GX-3R 4-Gas Confined Space Monitor, LEL / O2 / Combo H2S / CO with Li-Ion Battery Pack with 100-240 VAC Charger by RKI Instruments

OSHA defines the breathing zone as a ten inch radius around the worker's nose and mouth, and requires that worker exposure monitoring air samples be collected in the breathing zone. Air sampling filters may be attached to the collar or lapel. Traditionally this means only a single gas monitor would be small enough for a worker to practically wear a gas monitor 'In the breathing zone'. Now there is a 4 gas monitor smaller than many single gas monitors.

The GX-3R is the worlds smallest 4 gas monitor weighing only 3.52 ounces and can comfortably be clipped within a worker's breathing zone (2.2" W x 2.55" H x 1.02" D). It simultaneously monitors and displays LEL combustibles, O₂, CO (Hydrogen compensated CO also available), and H₂S.

The GX-3R represents the latest evolution of gas detection technology utilizing a new generation of micro sensors. The LEL sensor has a unique design with two active filaments in one sensor to increase it's resistance to silicone poisoning. If one filament gets poisoned the second filament takes over. The new O₂ sensor is electrochemical with a 3 to 5 year life span. H₂S and CO are now available in a combo micro sensor.

Safety supervisors will appreciate the non-compliance indicator. The instrument flashes it's 3 LED lights every 30 seconds in the following conditions; if the instrument has not been bump tested, or if calibration is due, or if there was a gas alarm event. The 3 LED lights will continue to flash once every 30 seconds until the non-compliance condition has been resolved. The 30 second interval is adjustable.

Features

• Smallest & lightest 4 gas monitor: 2.2" W x 2.55" H x 1.02" D, 3.52 ounces
• Simultaneous detection of 4 gases: LEL, O2, H2S & CO; H2 Compensated CO sensor available
• Simple 2-button operation
• Non-Compliance Indicator
• Alarms: audible, visual, & vibration
• 3 user adjustable alarm levels
• Impact resistant body with removable rubber boot
• Large LCD Auto-backlit display
• 25 hours of operation (Lithium-ion battery)
• Field replaceable sensors & filters
• Water and dust resistant design, IP66/68
• Stealth mode for law enforcement
• 3 Year warranty

Applications

• Personal monitoring
• Confined spaces
• Refineries/petrochemical
• Utilities
• Oil and Gas
• Water/wastewater
• Fire services
• Construction

*Please note we can only ship RKI products to customers within the United States

TK1181-Z Chlorine Dioxide Test Kit, 1 drop = 50, 100 or 500 ppm as ClO2 by AquaPhoenix

EndPoint ID Drop Count Test Kit, Chlorine Dioxide

1 drop = 50, 100 or 500 ppm as ClO2

Build your brand with EndPoint® ID test kits that are private labled with your company logo and contact information. EndPoint ID test kits include color pictures, icons and video to help simplify the testing process. Each kit comes with instructions, reagents, test vial and required accessories all packaged in a durable plastic case. Test kit case and reagents can be private labeled with your company logo and contact information.

EndPoint ID Features:

• Color coded caps for easy test parameter identification
• Color pictures to help identify color changes while testing
• Scannable QR codes link to training videos via your smart phone
• Visual icons for testing and safety tips to remind users of best practices
• Interferences are listed for increased accuracy
• Printed on durable synthetic paper that is waterproof, chemical-resistant and tear-resistant
• Private labeled with your company logo and contact information

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

6231M pH/mV/Temp Microprocessor Handheld Meter with 3-Point Calibration by Jenco

pH/mV/Temp. microprocessor handheld meter in splash proof case with 3 point calibration, 40 memory storage, BNC, pH/ORP connector with 8-pin DIN ATC connector. AC/DC power. CE Approved

• 3 point calibration
• 40 memory storage
• Power down memories
• Electrode offset recognition
• Electrode slope recognition
• Built in buffer temp. coefficients
• ATC
• CE approved
• Splash resistant/watertight case
• Battery/ac adaptor
• High 50/60hz noise rejection
• UL approved ac line adaptor
• Aconventional 9v battery
• Highly reliable mechanical touch keys with audio feedback

M-700056 Manning AirScan IRF9 Transmitter, R407A 0-1,000 ppm, stainless steel enclosure by Honeywell Analytics

The industrial refrigeration industry is changing rapidly. The manufacture of R-22 and other HCFCs are being phased out. Influential organizations such as EPA and CARB (California Air Resources Board) are enforcing lower level monitoring requirements. Manufacturers of cooling systems are introducing new equipment that runs on 407a, 422d, 410a, HFO-1234yf, NH3 and CO2. In step with these changes, EPA fines have escalated for anyone venting ozone-depleting gases. What's your best move? Contact Honeywell Analytics to learn how to detect for these new refrigerants. With Honeywell Analytics, you can green the environment—and green your bottom line.

Honeywell Analytics Infrared monitoring solutions are designed to help your plant operate more efficiently and cost effectively. Unlike sample draw systems which take longer to pinpoint a gas leak, our diffusion sensing technology cuts downtime and the cost of expensive refrigerant replacement. Other technological advantages include flexible standalone or networkable configurations, long operating life expectancy (10+ years); fewer calibration requirements; self-monitoring SensorCheck technology; EPA compliance including newer requirements set by CARB (California Air Resources Board); and accurate, reliable response to the most common refrigerant gases used in industrial or commercial processes.

Refrigerant Specific

• Rapid response to refrigerants including R-404a, R-22, R-507a, R-134a, R-407a, R-410a, R-422d, HFO-1234yf, NH3 and CO2
• Internal monitoring of 4/20 mA loop circuitry continuously
• Compliant with new monitoring standards set by CARB

Diffusion-Design Sensor

• Has no moving parts and doesn't require pumps or filters
• All points of detection can be monitored continuously at an affordable cost

Versatility

• Can be used with any Honeywell Analytics readout
• Standard range of 0-3,000 ppm, can be rescaled for lower trip points
• Provides a linear output of 4/20 mA as a function of refrigerant concentration
• Simple, real-time calibration eliminates maintenance downtime
• Automatically adapts to fluctuating temperatures

Long-Lasting Performance

• Unique internal reference channel compensates for dust particles, source degradation, humidity and temperature fluctuation, food odors, chemical cleaners, etc.

ATMOS™ Technology

• Allows for operation down to -60°F and in condensing humidity environments or during washdown
• Automatically adapts to its environment and provides accurate and reliable performance under the harshest conditions

SensorCheck™ Technology

• Checks operating parameters of sensors and sends a notification output signal if an anomaly is identified
• Tests the sensor every 24 hours for electrical viability
• Indication can be detected by a Manning gas monitor or PLC

Housing

• High-mass metal bench provides structural and thermal stability and greater immunity to vibration
• Superior EMI/RFI shielding

Applications

• Banana and Produce Rooms
• Beverage Plants
• Wineries and Breweries
• Confined Space Entry
• Food Processing
• Gas Bottling Plants
• Ice Rinks
• Product Coolers
• Rack Houses
• Refrigeration Systems
• Supermarkets

MBB3-A1C1E00-020 MultiRAE Pumped Portable Multi-gas Monitor - 10.6 eV PID / LEL / O2 / Li-ion Battery / Non- Wireless by RAE Systems

The MultiRAE is the most advanced portable chemical detector on the market. The MultiRAE delivers the broadest PID sensor range in its class and the versatility to support 25 intelligent interchangeable sensor options (such as PID, NDIR for combustibles and CO2, ammonia, chlorine, formaldehyde, and phosphine) to fully meet the monitoring needs in a variety of applications, including industrial hygiene, personal protection, leak detection, and HazMat response.

The MultiRAE's optional wireless capability improves safety by providing commanders and safety officers real-time access to instrument readings and alarm status from any location for better situational awareness and faster incident response.

Key Features

• Wireless access to real-time instrument readings and alarm status from any location
• Unmistakable five-way local and remote wireless notification of alarm conditions including Man Down Alarm
• Intelligent sensors store calibration data, so they can be swapped in the field
• Extensive on-board gas libraries (190 VOCs and 55 combustible gases)
• Largest display in its class
• Continuous datalogging (6 months for 5 sensors, 24x7)

Applications

• Aviation (wing tank entry)
• Chemical
• Environmental
• Oil and gas
• Pharmaceutical
• Shipping / marine
• HazMat response
• Clandestine drug labs

MC310 EC - Conductivity Monitor by Milwaukee

The MC Monitors are designed to continuously monitor pH, EC or TDS values directly in your reservoir. Each unit features a user selectable set-point. An LED visual alarm is activated and flashes when the pH, EC or TDS level rises either Above or Below (user selected) that set-point.

All these instruments run on a 12V adapter so there's no need to worry about failed batteries and each unit comes with mounting kit, probe, probe holder and starter calibration solution.

• User selectable Hi/Low Set Point
• Manual 1 points calibration
• Visual LED alarm
• Supplied with 12 VDC adapter, mounting kit, and 20ml 1413 µS/cm calibration solution
• MA811/2 EC Conductivity Probe with 2m cable (BNC connector)

72-6APM-C GX-6000 Six Sensor Sample Draw Gas Monitor, LEL / O2 / H2S / CO / Cl2(0-10.0 ppm) / NH3(0-400 ppm), with Li-ion Battery Pack / 100-240 VAC Charger by RKI Instruments

Simply put, the GX-6000 is a game changer. This powerful hand-held instrument is capable of simultaneously monitoring up to 6 gases. In addition to the standard 4 confined space gases which include combustibles, O2, CO, & H2S, the GX-6000 has 2 additional smart channels that accept PID, IR or super toxic sensors. Equipped with a strong internal sample pump, a man-down alarm, a panic alarm, an LED flashlight, and large auto rotating LCD display, the GX-6000 can operate as a single gas PID unit or a multifunctional tool utilizing all 6 channels. The GX-6000 with a PID sensor will come equipped with a library of over 600 VOC gases to choose from as standard. Choosing from the library is easy with a personalized favorites list of 30 commonly used VOC's as well as a list of 8 of the most recently used VOC's.

The GX-6000 has a rugged design built for the nastiest environments. It is equipped with a removable impact-resistant rubber boot and a dust and water resistant enclosure with an IP-67 rating. With 5 bright LED lights on 3 sides of the instrument, alarms are easily seen from a variety of perspectives. With vibration and loud audible alarm, GX-6000 will easily alert users when needed.

Features

• Monitor up to 6 gases
• 2 smart sensor slots auto recognize PID, IR, and super toxic sensors
• 5 Operating modes: normal, leak check, inert, snap log and bar hole
• Library of over 600 VOCs
• PPM Leak Check mode
• Man-down and panic alarms
• Auto display rotation
• LED Light source
• Internal sample pump
• Glove friendly glow in the dark buttons
• Light weight, small, rugged IP-67 design
• Interchangeable battery packs Li-ion / alkaline
• Operates up to 14 hours on Li-ion battery pack, fully recharges in 3 hours
• Field replaceable sensors, batteries and filters

Applications

• Confined space entry
• Hazmat response teams
• Arson investigation
• Remediation sites
• Perimeter monitoring
• Leak detection
• Landfill monitoring
• Wing tank entry

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

72-5445RK Eagle Portable Monitor for LEL & PPM O2/CO/HF/NH3 (No Probe) by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

98767-12 Traceable® Vane Anemometer with RS-232 Output and Calibration by Digi-Sense

This vane anemometer measures and displays wind speed/air velocity and temperature simultaneously on the 1/2"H LCD. Switch between five units of measure and °F/°C with the press of a button. Recall Min/Max temperatures and velocities, or freeze the display with the HOLD feature. RS-232 output allows for data acquisition to monitor and store readings on your PC. Robust construction handles years of use in the lab or field.

Traceable® products are calibrated to NIST-traceable standards and ready to use as soon as you receive it. Each product goes through an intense vetting process before it can carry the Traceable name, and it includes NIST-traceable certification. This means that a 17025-accredited calibration test lab has confirmed that the product meets or exceeds all stated specifications, saving you both time and money by not having to calibrate separately.

NIST-traceable calibration also helps you meet quality standards and regulatory compliance for ISO, FDA, cGMP, VFC, CAP, CLIA and Joint Commission requirements.

Data acquisition software is not included - please see part number 37804-14 for software and connection cable needed.

• Get accurate, reliable measurements with included NIST-traceable calibration
• Dual-line LCD shows both temperature and air velocity at the same time
• Recall Min/Max readings and freeze display with HOLD feature
• Connect to a PC to monitor and store readings

Includes

One 9V battery, hard-sided carrying case, and NIST-traceable calibration certificate with data.

WD-00652-66 Traceable® One-Shot™ Conductivity and TDS Standard, 1000 μS; 6 x 100 mL Vials by Oakton

• Oakton® Traceable® conductivity and TDS standards have detailed labels: KCl, NaCl, and 442 conversions, temperature corrections, and certified values referenced to 25°C-convenient!!
• Average accuracy at 25°C is ±0.25 microsiemens for 1, 5, 10 microsiemen (μS) solutions, or ±0.25% for all other solutions. The tested uncertainty is shown on the certificate, whichever is greater
• Conductivity options range from 1 to 200,000 μS/cm
• Individually-tested solutions are certified by the bottle - each bottle is analyzed for the best accuracy

METHODS SUPPORTED

Certified reference material meets test requirements for Federal, State, and local agencies, CAP, ASTM, NCCLS, CLSI, ACS, CLIA, AOAC, EPA, APHA, AWWA, WEF, USGS, USP, and ISO. Traceable® Conductivity Standards complies with and is essential for use in these official methods: AOAC 973.40, EPA 120.1, Standard Method 2510 (APHA, AWWA, WEF), ISO 7888, DIN 38404, ASTM D1125, USGS I-1780, USP 645, and for A2LA/NVLAP accreditations/ISO 9000 certifications. Material may be used to calibrate all conductivity meters and to determine all conductivity cell constants.

A2LA ACCREDITATION ISO/IEC 17025:2005 (1750.01)

To assure accuracy an individually serial-numbered Traceable® Certificate is supplied to indicate traceability to standards provided by NIST (National Institute of Standards and Technology) and/or a National Standards Laboratory. A2LA accredited certification provides the highest achievable level of quality assurance, documentation, and accuracy. Conductivity Standards are produced in an A2LA accredited ISO/IEC 17025:2005 (1750.01) calibration laboratory. Additional certifications include ISO 31 (certificate content) and ISO 35 (statistical analysis), plus ISO 9001 (certified quality manufacturer).

• All Oakton® Traceable® conductivity standards are NIST-traceable reference materials
• Supplied with a calibration report from an ISO 17034 and ISO 17025 accredited laboratory
• These standard solutions let you calibrate conductivity instruments to ensure accuracy
• If unopened, shelf life is one year; once opened, shelf life will vary by solution value
• Use when readings are expected to be around 1000 μS/cm

INCLUDES

temperature compensation chart, TDS conversion chart, and NIST-traceable calibration certificate with data.