All Products

T4-ZOCA-H2-STANDARD T4 Personal Gas Monitor, 3 Gas - O2, CO (H2 resistant), CH4 % LEL, Alternate Alarm Levels / Certifications by Crowcon

T4 integrates innovative safety features and an intuitive, rugged design to provide advanced protection for those working in harsh environments. This portable multigas detector, which is exceptionally easy to use and service, protects against the four most prevalent gas hazards: carbon monoxide (CO), hydrogen sulphide (H₂S), flammable gases and oxygen (O₂) depletion.

Features

• TWA resume function - unique to T4, this innovative feature ensures toxic gas exposure is calculated accurately over an entire shift, even if T4 is switched off for a break or during travel to another site.
• 18 hour battery life - safely work multiple or longer shifts between charges, covered by the 18 hour battery life.
• Backlit display - large, clear display with backlight and option to flip the screen 180° for easy viewing while worn.
• Rugged design - with a thick anti-shock rubber casing and drop-tested to 13.1 feet on concrete, T4 provides dependable operation under the most demanding use.
• Water & dust-resistant to IP65 & IP67 - provides protection in the harshest environments.
• Dedicated sensors - one sensor for every gas ensures effective, fast and reliable detection.
• Positive safety indicator - a simple 'traffic light' status indicator which, at a glance, provides visual assurance of operational and compliance status to both users and supervisors. Green light - Working safely. Red light - Attention required
• Intrinsically safe - ATEX approved and UL Class 1 Div 1 for safe operation in a wide range of hazardous environments.
• Multiple alarms - audible 95dB alarm, bright red/blue LED's and vibrating alerts provide effective warning to gas hazards.
• Easy operation - large single button and intuitive menu system minimize training and allow easy operation while wearing gloves.

WD-35413-00 pH/Con 700 Benchtop Meter with pH Electrode, Conductivity/Temp Probe, and Electrode Stand, 110/220 VAC, 50/60 Hz by Oakton

Easily toggle between pH, mV, conductivity, TDS, and temperature measurements at the touch of a button

The pH/CON 700 meter offers a new compact design that is over 40% smaller than other benchtop meters. The large display is easy to read even at a distance. Dual-display allows you to read both a measured parameter and temperature at a glance. The meter features pH auto-buffer recognition for both USA and NIST buffer sets (1.68, 4.01, 7.00, 10.01 and 12.45 or 1.68, 4.01. 6.18. 9.86, and 12.45), automatic or manual temperature compensation, temperature selectable in either °F or °C, display HOLD, and water-resistant membrane keypad.

Previous calibration points, electrode slope and offset, and conductivity/TDS cell constants are stored in memory for quick and easy retrieval. The convenient pull-out quick reference card keeps keypad functions at your fingertips.

• Space-saving design takes up less room on the bench than other meters
• Large display lets you see your measurements from across the lab
• Conductivity and TDS autoranging chooses the best resolution for each measurement

*Please note we can only ship RKI products to customers within the United States

6300-8091 MGS-150 Gas Transmitter, CO2 IR: 0 - 10,000 ppm, Duct Mount IP66 Housing by Bacharach

MGS-150 Series Gas Transmitter is a feature-rich gas detection system with a wide range of sensor options to provide real-time monitoring of refrigerant, combustible, and toxic gases. It comes standard with user-selectable analog and digital outputs that can be set for 4-20 mA, 0-5V, 1-5V, 0-10V, or 2-10V; allowing them to connect directly to most BMS, SCADA or control systems. Alarm indicators include an onboard alarm LED and audible buzzer, in addition to an alarm relay for connection to external audible/visual alarms or a BMS system. The product's alarm threshold value is pre-set to factory defaults but is also field programmable. A variety of housing options are available (shown below), from standard IP41 enclosures to IP66 water resistant housings, which allow the MGS-150 Series gas sensors to be placed in the toughest of conditions.

Ideal for Commercial and Industrial Refrigeration, Food Storage and Food Processing Facilities, Supermarkets, Parking Garages, Wastewater Treatment Facilities, Hospitals and Universities.

Features & Benefits:

• Infrared, semiconductor and electrochemical sensor options to meet almost any gas detection need - at the most affordable cost.
• User-selectable analog outputs: 4-20 mA, 0-5V, 0-10V, 1-5V, 2-10V featuring 12/24 VAC/VDC operation.
• Fast-response sensors detect leaks quickly, which protect personnel and minimize refrigerant gas usage and environmental impact.
• Long-life semiconductor sensors for detection of all refrigerants, ammonia, halocarbons, combustible gases & VOCs.
• Robust design and remote sensor options allow units to be placed directly in areas where detection is needed.
• Available in a variety of housings, including IP66 and duct mount, for placement in the toughest of environments.

Part Number: 34L-481

SS4-AS2-C-E-M Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) M25 with MA420-4 4-20 mA Module for SS4 Detectors by Honeywell Analytics

The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

Fire Sentry SS4-A

The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

Fire Sentry SS4-AS

The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

Fire Sentry SS4-AUV

The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

Operation

The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

Fire Sentry SS4-A and SS4-AS Features:

• Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
• Built-in test for optical "through the lens" testing
• False alarm immunity
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option
• Meets SIL 2 requirements

Fire Sentry SS4-AUV Features:

• Senses solar-blind ultraviolet band
• Built-in test for optical "through the lens" testing
• Utilises long-life, ruggedised UV sensors
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option

Applications include:

• Petrochemical facilities and Refineries
• Co-Generation plants
• Aircraft hangars
• Silane and Hydrogen gas storage
• Gas Turbines and power plants
• Gas compressor stations
• Warehouses
• Semiconductor

*Please note we can only ship RKI products to customers within the United States

Old Part Number: Z105120
New Part Number: Z105120PN

MCXL-XUHM-Y-AU GasAlertMicroClip XL Detector, Combustible (% LEL, Unfiltered), Oxygen (O2), Hydrogen Sulfide (H2S), Carbon Monoxide (CO) - Yellow Housing, AU version (Australia) by BW Technologies

The easy to wear, slim and compact GasAlertMicroClip provides affordable protection from atmospheric gas hazards. For standard operation with features you can count on, opt for the GasAlertMicroClip XT. For extended battery life, especially in cold weather, choose the GasAlertMicroClip XL. Both offer visual compliance at a glance with the flashing, green IntelliFlash™. Easy onebutton operation reduces training time and lets workers focus on the job at hand. For simple, cost-effective management of your records, calibration and bump testing, choose BW's MicroDock II automatic test and calibration system and Fleet Manager II software.

• Easy and comfortable to wear; thin and lightweight
• Easy operation and straightforward training with one-button simplicity
• Easy visual compliance with flashing, green IntelliFlash™
• Easy and cost effective to own

Additional GasAlertMicroClip features:

• Choose the GasAlertMicroClip XL for cold weather performance
• IntelliFlash™ verifies operation and compliance to both the user and supervisor
• Tamper-proof, one button operation
• Powered by a rechargeable lithium polymer battery

Standard features of BW multi-gas products:

• Continuous LCD shows real-time gas concentrations
• Compact and lightweight design makes it comfortable to wear
• Water-resistant
• Simple automatic calibration procedure; compatible with BW MicroDock II automatic test and calibration station
• Full function self-test of sensor, battery status, circuit integrity and audible/visual alarms on start up
• Bright wide-angled visual alarm bars
• Built-in concussion-proof boot
• Multi-language support in English, French, German, Spanish and Portuguese
• Conveniently manage your fleet using Fleet Manager II

Part Number: MCXL-XUHM-Y-AU

M020-0025-003 MUNI MP425 Pre-Configured Four-Gas Detector, LEL/O2-LF/CO/H2S - Li-ion Poison-filtered LEL version, to be used for methane only by mPower Electronics

The MUNI MP420 is a compact and lightweight 4-gas detector for worker safety at hazardous locations, with four standard sensors for oxygen (O₂), combustibles (LEL), carbon monoxide (CO) and hydrogen sulfide (H₂S). Alternative sensors are lead free oxygen (O₂), low power infrared methane (CH₄), sulfur dioxide (SO₂), and hydrogen cyanide (HCN). The detector is packaged in a robust housing with no moving parts. Its battery power offers 2 work shifts of run time for a standard 4-gas detector, and extended run time using a low-power infrared sensor. The simple, 2-button operation results in ultimate ease of use and significantly reduced time spent training the user.

Features, Functions and Benefits

• Compact, robust, lightweight & wearable
• Auto backlit LCD with large numeric digits
• Easy-to-navigate menu with two buttons
• Battery operation 24 hours with pellistor LEL sensor; extended time with lowpower infrared LEL sensor
• Tri-color status indicators on regular self-diagnosis of sensor, battery & circuit
• Wide angle LED alarms
• 1000 Events log
• Combination charge adapter / micro-USB PC interface cable
• IP-68 weather ingress rating
• Up to four replaceable sensors; non-interchangeability reduces monitor cost
• Optional BLE wireless connectivity
• Optional MuniDock for convenient bump & calibration

SH6168-Q Sodium Hydroxide, 0.02N, 1L by AquaPhoenix

• Traceable to NIST

Specifications

• Concentration: 0.02N
• Packaging Type: Poly
• Size: 1.00 L

98767-54 Traceable Ultra™ Refrigerator/Freezer Thermometer with Calibration; 1 Bottle Probe by Digi-Sense

Accurately monitor temperatures in refrigerators, freezers, water baths, and incubators. Thermometers have accuracy of ±0.5°C (-30 to 50°C). Built-in audible and visual alarms activate when temperature rises or falls below the alarm set point, and is programmable in 0.1° increments.

Traceable® Products have an individually-numbered Traceable® Certificate provided with each unit, that assures accuracy from our ISO/IEC 17025:2017(1750.01) calibration laboratory accredited by A2LA. It indicates traceability of measurements to the SI units through NIST or other recognized national measurement institutes (NMI) that are signatories to the CIPM Mutual Recognition Agreement. Each product goes through an intense vetting process before it can carry the Traceable name, thus saving you both time and money by not having to calibrate separately.

Thermometer comes with a bottle probe filled with nontoxic glycol solution, eliminating the possibility of contamination from mercury. Solution is GRAS (generally recognized as safe) by the FDA. The solution filled bottle simulates the temperature of other stored liquids and eliminates the rapid temperature fluctuation caused by opening the refrigerator/freezer door.

• Includes NIST-Traceable certificate from our A2LA accredited (1750.01) calibration laboratory|Triple display simultaneously shows MIN/MAX and current temperature|10-ft microcable allows refrigerator/freezer doors to close on it
• Temperature-buffered glycol bottle probe mimics solution

Includes

glass bottle probe with 10-ft cable, flip-open stand, hook-and-loop strips, magnetic strips, wall mount, batteries, and NIST-traceable calibration certificate with data.

*Please note we can only ship RKI products to customers within the United States