$750 - $1000

2811-000-001 EC 28 Gas Transmitter with Sensor, with Sensor, No Display by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

*Please note we can only ship RKI products to customers within the United States

3015-8004 H-10 PRO Refrigerant Leak Detector with charger, N. American plug only by Bacharach

MSA Bacharach's H-10 PRO is a highly responsive universal refrigerant leak detector using Bacharach's tried-and-true heated diode sensor technology. It's ultra-sensitive to all halogen-based, non-flammable CFC, HFC and HCFC refrigerants for reliable use in a wide range of refrigerant leak detection applications.

The H-10 PRO has a long probe (4.5 ft./1.4 m) for detecting leaks in hard-to-reach areas, visual and audible indicators to show relative leak sizes and an auto-zeroing feature (automatic mode only) for finding leaks in backgrounds where target gas is present. It has an internal sensor calibration reference to ensure optimum performance and comes with a 3 year warranty.

Features

• Detects all CFC, HFC and HCFC refrigerants as low as 0.006 oz/yr, including R-410a and R-507
• Dual power options allow battery operation for the best mobility or wall power for uninterrupted usage
• Visual and audible indicators include an incremental flashing LED in the probe tip, an internal speaker and a headphone jack

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

3300-001 CC 33 Fixed Transmitter with Aluminum Housing, 4-20 mA No Relay by GfG

It has always been our aspiration to combine innovative ideas and technology with functional design. This is how quality and longevity come about. Attributes symbolic of the name GfG in gas measurement.

Are you looking for an innovative transmitter for flammable gases, but need explosion protection? Then a transmitter from the GfG 33 series is the right choice.

Robust housing for every application

The transmitters of the 33 series are flameproof encapsulated and fulfill the requirements of the type of protection "d". Depending on the application, you can choose the 33 transmitter with an epoxy-based aluminum or a pure stainless steel housing. In order to meet the quality requirements of our customers and our own standards in terms of durability, we use a particularly high-quality and durable Viton seal in the 33 series. This can withstand even the toughest operating conditions for many years.

Variants

GfG offers the CC 33 in two variants:

For conventional industrial The CC 33 is available in a lacquered die-cast aluminum housing with 10mm thick bulletproof glass. Applications with special conditions such as e.g. in the Food industry can be covered by a unpainted housing made of stainless steel with a 15mm thick bulletproof glass.

Operation by means of magnetic pin

The three magnetic switches behind the protective glass, which is up to 15mm thick, can be operated using the GfG magnetic pin. The GfG typical three-button operation is easy to understand. The menu is clearly structured and logically structured.

All transmitters of the 22, 29 and 33 series have a uniform user interface. The uniform operation and the logical system structure keep your training and maintenance effort as low as possible.

Proven and innovative is not a contradiction

The CC 33 works on the principle of catalytic heat generation (WT), a proven method for measuring combustible gases. The transmitters are equipped with high-performance electronics for voltage stabilization, processing of measured value output and temperature compensation. The long life of the sensors minimizes follow-up costs.

Sensor technology

With improved sensor technology and the unique GfG "chimney effect", the CC 33 transmitter for combustible gases has one of the fastest response times in the world. There are more crucial seconds left to initiate countermeasures and to bring people to safety.

Universal signal transmission

The measured values and status displays of the 33 series can be transmitted either analog or digital via the Modbus interface. Due to the different variants of signal transmission, a transmitter of the 33 series can be connected to almost any gas warning system as an additional measuring point or in exchange for existing transducers.

Signal processing

The embedded software of the 33 transmitter linearises the measurement signal and compensates for temperature influences. As a result, correct measured values are transmitted even in the event of weather-related temperature fluctuations. The execution of the software enables the detection of faults and, in the Modbus variant, the requirement of required service or maintenance work.

Smart sensors

Pre-calibrated sensor modules can be screwed directly into the sensor receptacle on the housing of the CC 33. The smart GfG sensors are pre-programmed with all the necessary parameters and can be used without much effort ("plug and play"). Sensor changes are shown in the display. (catalytic and electrochemical sensors)

Three freely programmable internal relays

The 33er transmitters can be used as a "stand-alone system". You can set the two alarm thresholds individually and freely program the optional three relays. You do not need a cable to a controller and you can nevertheless reliably switch safety-related devices.

With colored graphic display

The clearly laid-out graphic display makes it easy to read the device status, the current measured value and many other important information. In the event of an alarm, the display turns red. The large LEDs signal from a distance the current device status and thus serve the rapid information of your employees about any alarms or malfunctions.

Using the display, you can easily navigate through the clear device menu and make various settings, including calibration, depending on your user authorization.

Calibration

For regular function control with gas application, a calibration adapter is placed on the transmitter to ensure a safe and even gas supply.

3300-002 CC 33 Fixed Transmitter with Aluminum Housing, 4-20 mA with Relay by GfG

It has always been our aspiration to combine innovative ideas and technology with functional design. This is how quality and longevity come about. Attributes symbolic of the name GfG in gas measurement.

Are you looking for an innovative transmitter for flammable gases, but need explosion protection? Then a transmitter from the GfG 33 series is the right choice.

Robust housing for every application

The transmitters of the 33 series are flameproof encapsulated and fulfill the requirements of the type of protection "d". Depending on the application, you can choose the 33 transmitter with an epoxy-based aluminum or a pure stainless steel housing. In order to meet the quality requirements of our customers and our own standards in terms of durability, we use a particularly high-quality and durable Viton seal in the 33 series. This can withstand even the toughest operating conditions for many years.

Variants

GfG offers the CC 33 in two variants:

For conventional industrial The CC 33 is available in a lacquered die-cast aluminum housing with 10mm thick bulletproof glass. Applications with special conditions such as e.g. in the Food industry can be covered by a unpainted housing made of stainless steel with a 15mm thick bulletproof glass.

Operation by means of magnetic pin

The three magnetic switches behind the protective glass, which is up to 15mm thick, can be operated using the GfG magnetic pin. The GfG typical three-button operation is easy to understand. The menu is clearly structured and logically structured.

All transmitters of the 22, 29 and 33 series have a uniform user interface. The uniform operation and the logical system structure keep your training and maintenance effort as low as possible.

Proven and innovative is not a contradiction

The CC 33 works on the principle of catalytic heat generation (WT), a proven method for measuring combustible gases. The transmitters are equipped with high-performance electronics for voltage stabilization, processing of measured value output and temperature compensation. The long life of the sensors minimizes follow-up costs.

Sensor technology

With improved sensor technology and the unique GfG "chimney effect", the CC 33 transmitter for combustible gases has one of the fastest response times in the world. There are more crucial seconds left to initiate countermeasures and to bring people to safety.

Universal signal transmission

The measured values and status displays of the 33 series can be transmitted either analog or digital via the Modbus interface. Due to the different variants of signal transmission, a transmitter of the 33 series can be connected to almost any gas warning system as an additional measuring point or in exchange for existing transducers.

Signal processing

The embedded software of the 33 transmitter linearises the measurement signal and compensates for temperature influences. As a result, correct measured values are transmitted even in the event of weather-related temperature fluctuations. The execution of the software enables the detection of faults and, in the Modbus variant, the requirement of required service or maintenance work.

Smart sensors

Pre-calibrated sensor modules can be screwed directly into the sensor receptacle on the housing of the CC 33. The smart GfG sensors are pre-programmed with all the necessary parameters and can be used without much effort ("plug and play"). Sensor changes are shown in the display. (catalytic and electrochemical sensors)

Three freely programmable internal relays

The 33er transmitters can be used as a "stand-alone system". You can set the two alarm thresholds individually and freely program the optional three relays. You do not need a cable to a controller and you can nevertheless reliably switch safety-related devices.

With colored graphic display

The clearly laid-out graphic display makes it easy to read the device status, the current measured value and many other important information. In the event of an alarm, the display turns red. The large LEDs signal from a distance the current device status and thus serve the rapid information of your employees about any alarms or malfunctions.

Using the display, you can easily navigate through the clear device menu and make various settings, including calibration, depending on your user authorization.

Calibration

For regular function control with gas application, a calibration adapter is placed on the transmitter to ensure a safe and even gas supply.

3300-003 CC 33 Fixed Transmitter with Aluminum Housing, RS 485 No Relay by GfG

It has always been our aspiration to combine innovative ideas and technology with functional design. This is how quality and longevity come about. Attributes symbolic of the name GfG in gas measurement.

Are you looking for an innovative transmitter for flammable gases, but need explosion protection? Then a transmitter from the GfG 33 series is the right choice.

Robust housing for every application

The transmitters of the 33 series are flameproof encapsulated and fulfill the requirements of the type of protection "d". Depending on the application, you can choose the 33 transmitter with an epoxy-based aluminum or a pure stainless steel housing. In order to meet the quality requirements of our customers and our own standards in terms of durability, we use a particularly high-quality and durable Viton seal in the 33 series. This can withstand even the toughest operating conditions for many years.

Variants

GfG offers the CC 33 in two variants:

For conventional industrial The CC 33 is available in a lacquered die-cast aluminum housing with 10mm thick bulletproof glass. Applications with special conditions such as e.g. in the Food industry can be covered by a unpainted housing made of stainless steel with a 15mm thick bulletproof glass.

Operation by means of magnetic pin

The three magnetic switches behind the protective glass, which is up to 15mm thick, can be operated using the GfG magnetic pin. The GfG typical three-button operation is easy to understand. The menu is clearly structured and logically structured.

All transmitters of the 22, 29 and 33 series have a uniform user interface. The uniform operation and the logical system structure keep your training and maintenance effort as low as possible.

Proven and innovative is not a contradiction

The CC 33 works on the principle of catalytic heat generation (WT), a proven method for measuring combustible gases. The transmitters are equipped with high-performance electronics for voltage stabilization, processing of measured value output and temperature compensation. The long life of the sensors minimizes follow-up costs.

Sensor technology

With improved sensor technology and the unique GfG "chimney effect", the CC 33 transmitter for combustible gases has one of the fastest response times in the world. There are more crucial seconds left to initiate countermeasures and to bring people to safety.

Universal signal transmission

The measured values and status displays of the 33 series can be transmitted either analog or digital via the Modbus interface. Due to the different variants of signal transmission, a transmitter of the 33 series can be connected to almost any gas warning system as an additional measuring point or in exchange for existing transducers.

Signal processing

The embedded software of the 33 transmitter linearises the measurement signal and compensates for temperature influences. As a result, correct measured values are transmitted even in the event of weather-related temperature fluctuations. The execution of the software enables the detection of faults and, in the Modbus variant, the requirement of required service or maintenance work.

Smart sensors

Pre-calibrated sensor modules can be screwed directly into the sensor receptacle on the housing of the CC 33. The smart GfG sensors are pre-programmed with all the necessary parameters and can be used without much effort ("plug and play"). Sensor changes are shown in the display. (catalytic and electrochemical sensors)

Three freely programmable internal relays

The 33er transmitters can be used as a "stand-alone system". You can set the two alarm thresholds individually and freely program the optional three relays. You do not need a cable to a controller and you can nevertheless reliably switch safety-related devices.

With colored graphic display

The clearly laid-out graphic display makes it easy to read the device status, the current measured value and many other important information. In the event of an alarm, the display turns red. The large LEDs signal from a distance the current device status and thus serve the rapid information of your employees about any alarms or malfunctions.

Using the display, you can easily navigate through the clear device menu and make various settings, including calibration, depending on your user authorization.

Calibration

For regular function control with gas application, a calibration adapter is placed on the transmitter to ensure a safe and even gas supply.

3300-004 CC 33 Fixed Transmitter with Aluminum Housing, RS 485 with Relay by GfG

It has always been our aspiration to combine innovative ideas and technology with functional design. This is how quality and longevity come about. Attributes symbolic of the name GfG in gas measurement.

Are you looking for an innovative transmitter for flammable gases, but need explosion protection? Then a transmitter from the GfG 33 series is the right choice.

Robust housing for every application

The transmitters of the 33 series are flameproof encapsulated and fulfill the requirements of the type of protection "d". Depending on the application, you can choose the 33 transmitter with an epoxy-based aluminum or a pure stainless steel housing. In order to meet the quality requirements of our customers and our own standards in terms of durability, we use a particularly high-quality and durable Viton seal in the 33 series. This can withstand even the toughest operating conditions for many years.

Variants

GfG offers the CC 33 in two variants:

For conventional industrial The CC 33 is available in a lacquered die-cast aluminum housing with 10mm thick bulletproof glass. Applications with special conditions such as e.g. in the Food industry can be covered by a unpainted housing made of stainless steel with a 15mm thick bulletproof glass.

Operation by means of magnetic pin

The three magnetic switches behind the protective glass, which is up to 15mm thick, can be operated using the GfG magnetic pin. The GfG typical three-button operation is easy to understand. The menu is clearly structured and logically structured.

All transmitters of the 22, 29 and 33 series have a uniform user interface. The uniform operation and the logical system structure keep your training and maintenance effort as low as possible.

Proven and innovative is not a contradiction

The CC 33 works on the principle of catalytic heat generation (WT), a proven method for measuring combustible gases. The transmitters are equipped with high-performance electronics for voltage stabilization, processing of measured value output and temperature compensation. The long life of the sensors minimizes follow-up costs.

Sensor technology

With improved sensor technology and the unique GfG "chimney effect", the CC 33 transmitter for combustible gases has one of the fastest response times in the world. There are more crucial seconds left to initiate countermeasures and to bring people to safety.

Universal signal transmission

The measured values and status displays of the 33 series can be transmitted either analog or digital via the Modbus interface. Due to the different variants of signal transmission, a transmitter of the 33 series can be connected to almost any gas warning system as an additional measuring point or in exchange for existing transducers.

Signal processing

The embedded software of the 33 transmitter linearises the measurement signal and compensates for temperature influences. As a result, correct measured values are transmitted even in the event of weather-related temperature fluctuations. The execution of the software enables the detection of faults and, in the Modbus variant, the requirement of required service or maintenance work.

Smart sensors

Pre-calibrated sensor modules can be screwed directly into the sensor receptacle on the housing of the CC 33. The smart GfG sensors are pre-programmed with all the necessary parameters and can be used without much effort ("plug and play"). Sensor changes are shown in the display. (catalytic and electrochemical sensors)

Three freely programmable internal relays

The 33er transmitters can be used as a "stand-alone system". You can set the two alarm thresholds individually and freely program the optional three relays. You do not need a cable to a controller and you can nevertheless reliably switch safety-related devices.

With colored graphic display

The clearly laid-out graphic display makes it easy to read the device status, the current measured value and many other important information. In the event of an alarm, the display turns red. The large LEDs signal from a distance the current device status and thus serve the rapid information of your employees about any alarms or malfunctions.

Using the display, you can easily navigate through the clear device menu and make various settings, including calibration, depending on your user authorization.

Calibration

For regular function control with gas application, a calibration adapter is placed on the transmitter to ensure a safe and even gas supply.

400520 0409 NIST Calibration Certification Kit for testo 400 Comfort kit (0563 0409) by Testo

Kits includes:

• NIST Temp Certificate with 3 Std. Pts
• NIST RH Cert. 2 Std Pts
• NIST Air velocity certificate at 3 standard points
• NIST Light certificate
• NIST Pressure certificate

400563 4161 416 Small Vane Anemometer Kit by Testo

The compact testo 416 anemometer with permanently attached vane probe with telescopic handle (max. 890mm). Volume flow is shown directly in the display. Accurate volume flow calculation due to easy input of duct area. Timed and multi-point mean calculation provide information on mean volume flow. Min/max values can also be shown in the display. The Hold function enables you to freeze the current reading in the display.

Kits includes:

• 0560 4160 - 416 Mini-Vane Anemometer
• 0516 0210 - Soft carrying case - small

• Direct display of volume flow
• Multi-point or timed mean calculation
• Max/min values
• Hold button to freeze readings
• Display light
• Auto-Off function
• TopSafe, instrument protection against dirt and knocks (optional)