$750 - $1000

Part Number: CG2C558

Part Number: SAIIL3A2

709A740 709 Combustion Efficiency Analyzer Kit by Test Products International

709 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature
• Dual input pressure with 0.001 inches water resolution for high efficiency & oil

A740 Features

• Easy to use
• Battery operated
• Self test facility
• Adjustable contrast
• Manual paper feed
• Maximum transmitting distance 16"(45cm)

A773

Use the A773 when working on oil fired appliances to extend the life of your sensors by eliminating acid gas exposure to your analyzer

65-2442RKSS-2K S2 Series Transmitter/Sensor/XP Stainless Steel J-Box, H2 Specific MOS, 0 - 2000 ppm Linearized by RKI Instruments

Having a reliable gas sensor is detrimental to the safety and security of workers in potentially unstable work environments. In many cases, the decision to use a gas detection device with a reliable sensor can be the difference between life and death. RKI Instruments understands the reliability of gas sensors should be a top priority for workplace safety managers. Their team of experts works diligently to incorporate the most advanced technologies with the highest industry standards.

For nearly 20 years, RKI Instruments has worked in the gas detection industry. Its line of products leads the industry in innovation and technology. Every year, the company commits to achieving a higher level of productivity and delivering the best gas detection products on the market. With the introduction of their high performing, low cost S2 Sensor Transmitter, RKI is fulfilling that commitment.

S2 Sensor/Transmitter

The RKI S2 Sensors and Transmitters use state of the art sensor technology to detect common gas hazards. Their efficient design and cost effectiveness make them an industry choice for atmospheric monitoring. The sensor transmitters can be used in both indoor and outdoor conditions and are designed to interface with RKI controllers or PLC/DCS systems.

The sensors are available in explosion proof casing for monitoring LEL, H2 specific, oxygen, H2S, CO2, and carbon monoxide. These sensors also have flame arrestors and are approved for use in hazardous environments. The oxygen, H2S, CO, and CO2 sensors are available in non-explosion proof models. The sensors provide highly specific and quick detection and are long lasting. The sensors can be quickly replaced while on the field and do not require any tools.

Explosion proof S2 Sensor/Transmitter

The explosion proof sensors use a variety of detection mechanisms including catalytic for LEL and LEL- H2 specific; metal oxide semiconductor for hydrogen; galvanic cell technology for oxygen; electrochemical for hydrogen sulfide and carbon monoxide; and infrared for carbon dioxide, methane, and hydrocarbons. A hydrogen specific sensor transmitter is not available. Each of these detection methods come with their own measuring range specifications and response times varying from 20 seconds to 45 seconds. These sensors are stainless steel and are housed in a cast aluminum explosion proof J-Box (a stainless steel J-Box is also available).

Non-explosion proof S2 Sensor/Transmitter

The non-explosion proof sensors use galvanic cells for oxygen detection; electrochemical technology for hydrogen sulfide, carbon monoxide, and other toxics; and infrared technology for carbon dioxide detection. The response times vary between 20 seconds and 60 seconds depending on the targeted gas, and the measuring ranges vary as well. These sensors are plastic or aluminum and housed in an explosion proof J-Box.

Accessories

The S2 Sensor/Transmitter has numerous accessories available to meet the individual workplace's needs. Such accessories include calibration adaptors, flow through adaptors, remote horns and lights, calibration kits, battery backups, splash guards, air aspirator adaptors or panels, and data loggers.

Each sensor comes standard with a one year warranty for materials and workmanship.

*Please note we can only ship RKI products to customers within the United States

712A740OIL 712 Combustion Efficiency Analyzer Kit by Test Products International

712 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature
• Dual input pressure with 0.001 inches water resolution for high efficiency & oil
• Optional A767 adapter for PC interface

A740 Features

• Easy to use
• Battery operated
• Self test facility
• Adjustable contrast
• Manual paper feed
• Maximum transmitting distance 16"(45cm)

Includes

• 712 Combustion Efficiency Analyzer
• A740 IR Printer
• A773 Sulfer Filter
• A790 Analog Oil Pressure Gauge
• A788 Smoke Pump Test

61-0191RK-10 Sensor, IR, Carbon Dioxide (CO2) 0 - 100%, Explosion Proof Direct Connection (No Transmitter, No J-Box), cULus Version by RKI Instruments

When working on potentially hazardous jobsites, safety managers should look for workplace safety solutions that are dependable and steadfast. When lives are on the line, a workplace cannot afford subpar safety products. That is why, at RKI Instruments, workplace safety is a top priority. Their Research and Development team work daily to integrate the latest technology with the best industry practices. With a reputation for excellent products, RKI Instruments introduces the latest in direct connect sensor technology. Designed for use in Class 1, Division 2 hazardous environments, the Direct Connect Sensors are designed specifically for RKI Beacon 110, 200, and 410 controllers.

Direct Connect Sensors

The RKI Direct Connect Sensors series gas sensors are state of the art gas detection sensors available for LEL, H2 Specific LEL, LEL IR, Oxygen, H2S, CO, CO2, and a variety of toxic gases. To use the Direct Connect Sensors, they can be used for remote detection by mounting them onto explosion proof junction boxes, or they can mount directly onto controllers and be used as a completely standalone system. Their unique plugin design allows for a quick and easy tool free installation on jobsites.

Detection solutions for a variety of hazardous environments

The Direct Connect Sensors are designed to be use in both indoor and outdoor settings. Additionally, some of the sensors are available in explosion proof models. The explosion proof models utilize a patented coating which serves double duty as also being water repellant. Users can also purchase splash guards to protect the sensors from very wet conditions.

Sensor Technology

Each sensor is crafted with stainless steel and housed in cast aluminum (stainless steel housing is available for some sensors). The Direct Connect Sensors are available in 2 forms: explosion proof and non-explosion proof. The explosion proof sensors are available as catalytic sensors for LEL, and LEL H2 specific. For hydrogen sulfide and carbon monoxide, the sensors utilize electrochemical technology which provides incredibly specific accuracy and quick response. Oxygen sensors work with galvanic technology, and infrared sensors for methane, hydrocarbons, and carbon dioxide. Non-explosion proof uses a galvanic sensor for oxygen; electrochemical sensors for hydrogen sulfide, carbon monoxide and other toxic gases; and infrared for carbon dioxide. Both explosion proof and non-explosion proof have 1 year warranties for materials and craftsmanship.

Specifications

The response times are under 30 seconds for all gases except hydrogen sulfide and carbon monoxide in the non-explosion versions (with a response time of 35 seconds) and non-explosion proof model sensor for toxic gases which has a 60 second response time. The life expectancy of all sensors are between 2 and 5 years.

The Direct Connect Sensors are compatible with several RKI Industries' accessories including calibration adaptors, flow through adaptors, remote horns and lights, calibration kits, battery backups, splash guards, air aspirator adaptors, and dataloggers.

*Please note we can only ship RKI products to customers within the United States

WD-08369-70 Economical Minidrum Hygrothermograph by Oakton

So economical, you ll want several for monitoring and recording environmental conditions

This hygrothermograph is so compact it fits almost anywhere- measures just 6.125"L x 7.5"H x 4"D. Quartz-controlled drive is employed for accuracy; operates for six months on one AA battery. Includes two felt-tipped pens (blue and red), one 7-day rotation chart and one AA battery.

• Includes AA battery (1), felt-tipped pens (1 red, 1 blue), and 7-day sheet of chart paper
• Compact size fits almost anywhere
• Record temperature and humidity on 7-day rotation
• Protective acrylic cover removes easily yet latches securely in place

2211005 CI 21 Fixed Gas Transmitter with Internal Sensor, Ammonia (NH3), 1 to 1000 ppm by GfG

The charge carrier injection (CI 21) sensor is a progressive development to improve upon current ammonia refrigeration detection methods. With CI 21 technology sensor life is no longer limited to ammonia exposure levels. This reduces replacement costs associated with electrochemical sensors.

Charge carrier injection technology also eliminates false alarms frequently associated with metal oxide sensing (MOS). These, along with other features, provide reliable, cost effective, longterm safety.

The CI 21 transmitter is an advanced development to which all other ammonia transmitters will be compared.

• Stable long-life charge-carrierinjection sensor
• Sensor is unaffected by exposure to high gas concentrations
• Low temperature operation to -40oF
• Low cross-sensitivity
• Eliminates costly false alarms
• Low cost of ownership

GS-AP-A Gasman Intrinsically Safe Personal Single Gas Monitor, Rechargeable Battery, 0-1ppm Ozone by Crowcon

For over 40 years, Crowcon Detection Instruments has produced state of the art gas detection devices for personal and industrial use. Building upon their reputation for reliable and innovative gas monitoring products, Crowcon introduces the Gasman personal gas monitor. Its lightweight and compact design is convenient for jobsites where workers need not be weighed down by excessive bulk and equipment. The unit conveniently clips to a pocket or helmet and operates continuously.

The Gasman personal gas monitor has numerous convenient features such as:

• One button technology
• Backlit LCD display
• Durable polycarbonate casing
• Quick response triple alert system
• Compact and lightweight design

Easy to Use

The Gasman s true one button technology is an ideal and simple design. The large glove friendly button is mounted on the front of the unit for easy access and controls all of the unit s programmable features. Also on the front, the Gasman s easy to read backlit LCD screen indicates gas readings and the battery status. The simple screen provides a clear indication of the unit s operation status. It will also alert the user 30 days in advance of when a calibration test is due. With a simple and intuitive design, Crowcon has produced a gas detector that reduces the complexities of workplace safety, and ensures workers in a straightforward manner that their equipment is on and operational.

Triple Alarm System

This portable single gas detection system features a triple alarm system that is sure to alert the user and anyone in the vicinity. The visible alarm utilizes a dual red and blue flashing LED light, and the unit houses an internal vibrating alert system. These two indicators allow for visual recognition in loud environments and working conditions. The alarm system also features a programmable audible alarm at 95 decibels. The unit is capable of a variety of alarm tones, and users can select which tone may be best for the individual workplace setting. The triple alarm system with multiple sensory indicators is sure to be noticed in almost any work environment.

Specifications

The Gasman single gas monitor is lightweight and compact, weighing less than 135 grams and with dimensions of 90 x 48 x 24 mm. The unit is available with a wide variety of gas sensors which feature various detection and alarm levels. The unit also features a quick response time of 20 seconds for flammable and toxic gases or 10 seconds for oxygen. Its datalogging feature has approximately 900 hours of storage and all events are time stamped. The battery life for this unit is incredible with 12 hours of runtime on a Rechargeable battery battery or up to 2 years on a non-Rechargeable battery.

WD-35418-00 pH 600 Portable Waterproof pH Meter with All-in-One pH/Temperature Probe by Oakton

Expanded range, resolution and accuracy, increased memory, and advanced communications

These waterproof handheld meters feature a 2.00 to 19.99 pH range expandable to 0.001 pH resolution. Combined with accuracies up to ±0.002 pH, these meters provide a new benchmark in our pH meter line.

Store up to 500 data sets in the meters memory. Time-and-date-stamping meets Good Laboratory Practice (GLP) standards.

The pH 600 meters offer the latest in calibration capabilities including up to 6 calibration points, a user-settable calibration due alarm, and up to 15 buffer options with auto buffer recognition of USA, NIST, DIN, and PWB standards.

The infrared IrDA wireless technology makes PC downloading more convenient and easier. Dual power up allows you to use batteries while out in the field or the optional AC power adapter while in the lab.

As always, our waterproof meters are IP67-rated for both dust and water intrusion. Even with no probes attached!

• No more excuses for missing data! Out-of-date or unperformed calibrations are now things of the past!

6500-2121 MGS-350 Gas Detector, VOC 0-2,000 IP66 Housing by Bacharach

Bacharach's MGS-350 Series Gas Transmitter is a feature-rich gas detection system with a wide range of sensor options to provide real-time monitoring of refrigerant, combustible, TVOC and toxic gases. It comes standard with analog and digital outputs including 4-20 mA, 0-5V, 0-10V and Serial Data, allowing them to connect directly to most BMS, SCADA or control systems. An onboard visual LED alarm indicator alerts area personnel when levels have exceeded the desired limit. The MGS-350 also features alarm relays (high and low) for connection to external audible/visual alarms or a BMS or BAS system.

MGS-350 Gas Transmitters, combined with the MGS Controller, can provide facility owners with a customized and complete low-cost gas-detection system. A variety of housing options are available (shown below), from standard to water resistant enclosures, which allow the MGS-350 units to be placed in many environments.

Features & Benefits:

• Detects refrigerants (CFCs, HFCs, HCFCs), TVOCs, combustible gases/hydrocarbons, O2, NH3, CO, H2S, H2, NO, NO2, SO2, Cl2, and O3
• Long-lasting infrared, semiconductor, catalytic bead and electrochemical sensor options for effective leak detection - at the most affordable cost.
• Precalibrated replacement sensors for easy maintenance
• Integrated visual LED alarm
• Two onboard alarm relays (low and high)
• Multiple housing options available, including IP 66 and duct mount, for placement in diverse environments.
• Analog outputs: 4-20 mA, 0-5V, 0-10V, featuring 12/24 VAC / 12-30VDC operation

WD-35604-04 CON 6+ Handheld Conductivity Meter Kit, -10 to 110°C Temperature Range and 0 to 20.00, 0 to 200.0, 0 to 2000 µS by Oakton

Features five measuring ranges up to 200.0 mS

These meters feature easy, push-button operation, a convenient HOLD function, and Auto-off function that shuts meter off after 20 minutes of non-use.

Meters offer two modes of five-point calibration. For quick and easy calibrations, use automatic mode with preset calibration points at the most popular values. For more flexibility, calibrate in the manual mode and set your calibration point at any value.

Set-up functions let you customize automatic temperature compensation and cell constant. The protective rubber boot helps shield your meter from drops and dings, and features a built-in stand.

CON 6+ features automatic or manual ranging across five ranges for a wide variety of applications ranging from pure water to boiler blow down water.

• High accuracy in changing temperature conditions
• Temperature readout and automatic temperature compensation (ATC)
• Calibrate the CON 6 at one point and all five ranges are covered

5921-0032 GDC-350 Gas Sensor Monitor, NEMA 1 Housing, Remote MOS TVOC Sensor by Bacharach

Bacharach's all new GDC-350 full-featured fixed gas monitors provide superior operation - standalone or as part of a larger system utilizing the standard analog outputs. This state-of-the-art instrument can detect a wide range of gases including carbon monoxide (CO), oxygen (O2), combustible gases, refrigerants and total volatile organic compounds (TVOCs). The GDC-350 provides a unique two sensor interface, allowing for multiple gases to be detected with onboard or remote sensors. Sensors can be located integral to the unit or remotely allowing for sensors to be placed directly in areas where potential leaks can occur. Bacharach s proprietary calibration algorithms extend the amount of time required between calibrations, reducing maintenance costs and lowering the overall cost of ownership for non-critical applications.

The GDC-350 has all the features and functionality for any application. LED alarm indicators visually indicate when alarm conditions are met and an audible alarm alerts nearby personnel. An onboard alpha numeric display shows gas readings in real time for each sensor. Integral dry contact relays are available to drive external audible / visual alarms, activate fans, or connect to building management and control systems. Installation and maintenance is simple and easy, reducing overall system cost. A pre-wired plug-in option is available for out-of-the-box operation. Simply plug the unit into any standard AC outlet for immediate detection and protection.

Xgard Gas Detectors

Crowcon is a global leader in designing and manufacturing gas detection technology and equipment. The company has been in operation for over 40 years and is consistently building upon its products. By integrating modern technology with the demands of the modern workplace, Crowcon has developed a line of gas detection devices and monitors that lead the competition. The Xgard range of gas detectors is a product of Crowcon s successful integration and technological advancements. With a wide range of sensor types and available accessories, the Xgard series is suitable for all worksites and is customizable enough to fit any needs.

Tough and reliable

The Xgard series of fixed point gas detectors is incredibly durable and reliable. The casings and materials, including weatherproof caps, are designed to protect the equipment from the harshest environments. The detectors are made from a variety of materials depending on the model: glass reinforced nylon, aluminum with polyester coating, and 316 stainless steel.

Variety of sensors

The fixed point gas detector offers a wide range of sensors for to suite almost all applications. The Xgard range of gas detectors is available in three models to meet varying worksite needs: flameproof, intrinsically safe, and safe area formats. Additionally, Xgard offers different types of fixed point gas detectors within these three models:

• Xgard Type 1- Intrinsically safe toxic and oxygen gas detectors
• Xgard Type 2- Flameproof toxic and oxygen gas detectors
• Xgard Type 3- Flameproof flammable gas detector
• Xgard Type 4- Flameproof high temperature flammable gas detector
• Xgard Type 5- Flameproof flammable gas detector with 4-20mA output
• Xgard Type 6- Flameproof thermal conductivity type gas detector
• Xsafe- Safe area flammable gas detector

Cost efficient and highly effective

With quick and easy installation and maintenance, the Xgard series is able to keep costs at a minimum. The replacement sensors, for example, are simple to replace by merely plugging them in. The replacement parts are also readily available and compatible with all Xgard models, thereby reducing the amount of required spare parts that are stored in the facility. Additionally, the sensors have two times the typical life spans of similar sensors in the industry. With a 2 year life span, worksites can expect to cut their sensor replacement costs in half. For worksites that require slightly more customization, Crowcon offers compatible accessories for the Xgard series such as sampling applications, remote gassing applications, spray deflectors, sun shields, weatherproof caps, collector cones, flow adapter, and accessories adapter.

Xgard also has flexible installation options. The unit is designed for either wall or ceiling mounts, and users will not need to purchase additional equipment for mounting. For more complex installation needs, users can purchase accessories.

Specifications

Each model is approximately the same size with dimensions of 6.1 x 6.5 x 4.3 inches and weighing approximately 1 or 2 pounds. The battery type, electrical output, and power requirements vary based on the sensor type. For a complete listing of gas sensors, types, and individual specifications, please see the product specifications listing.

GPB-0001-NU-C Gas-Pro 4-Gas Monitor, Non-pumped with Flow Plate, CO/H2S/O2/CH4, Multi-region PSU & Cradle by Crowcon

Crowcon Gas-Pro is a confined space entry monitoring solution for workers and fleet managers, and is now supported by the Crowcon I-Test bump test and calibration station.

Offering detection of up to 5 gases in a compact and rugged solution, Gas-Pro has an easy-to-read top mount display combining ease of use and user focused features.

An optional internal pump, activated with the flow plate, takes the pain out of pre-entry testing and allows Gas-Pro to be worn either in pumped or diffusion modes.

User friendly

• Top mount display
• Simple single button operation
• Intuitive functionality
• Makes it easy to read at a glance
• Reduces training time
• Can be used whilst wearing gloves

Adaptable

• Monitor 5 gases from many different options
• Pumped and diffusion solutions
• Multiple languages
• Automatic fail safe flow plate recognition
• Specific and unique Pre-Entry Check (PEC ) mode
• Offers multiple uses within one compact detector
• Takes away the pain of pre-entry testing

Reliable

• Reliable lithium-ion battery
• Water and dust resistant to IP65 and IP67
• Bump and calibration reminders
• Provides over 14 hours use from a 7.5 hour charge
• Capable of withstanding harsh environments
• Full compliance

65-2444-500-05 S2 Series Sensor/Transmitter, MOS, Hexane (C6H14) 0-500 ppm with explosion proof j-box, CSA by RKI Instruments

Having a reliable gas sensor is detrimental to the safety and security of workers in potentially unstable work environments. In many cases, the decision to use a gas detection device with a reliable sensor can be the difference between life and death. RKI Instruments understands the reliability of gas sensors should be a top priority for workplace safety managers. Their team of experts works diligently to incorporate the most advanced technologies with the highest industry standards.

For nearly 20 years, RKI Instruments has worked in the gas detection industry. Its line of products leads the industry in innovation and technology. Every year, the company commits to achieving a higher level of productivity and delivering the best gas detection products on the market. With the introduction of their high performing, low cost S2 Sensor Transmitter, RKI is fulfilling that commitment.

S2 Sensor/Transmitter

The RKI S2 Sensors and Transmitters use state of the art sensor technology to detect common gas hazards. Their efficient design and cost effectiveness make them an industry choice for atmospheric monitoring. The sensor transmitters can be used in both indoor and outdoor conditions and are designed to interface with RKI controllers or PLC/DCS systems.

The sensors are available in explosion proof casing for monitoring LEL, H2 specific, oxygen, H2S, CO2, and carbon monoxide. These sensors also have flame arrestors and are approved for use in hazardous environments. The oxygen, H2S, CO, and CO2 sensors are available in non-explosion proof models. The sensors provide highly specific and quick detection and are long lasting. The sensors can be quickly replaced while on the field and do not require any tools.

Explosion proof S2 Sensor/Transmitter

The explosion proof sensors use a variety of detection mechanisms including catalytic for LEL and LEL- H2 specific; metal oxide semiconductor for hydrogen; galvanic cell technology for oxygen; electrochemical for hydrogen sulfide and carbon monoxide; and infrared for carbon dioxide, methane, and hydrocarbons. A hydrogen specific sensor transmitter is not available. Each of these detection methods come with their own measuring range specifications and response times varying from 20 seconds to 45 seconds. These sensors are stainless steel and are housed in a cast aluminum explosion proof J-Box (a stainless steel J-Box is also available).

Non-explosion proof S2 Sensor/Transmitter

The non-explosion proof sensors use galvanic cells for oxygen detection; electrochemical technology for hydrogen sulfide, carbon monoxide, and other toxics; and infrared technology for carbon dioxide detection. The response times vary between 20 seconds and 60 seconds depending on the targeted gas, and the measuring ranges vary as well. These sensors are plastic or aluminum and housed in an explosion proof J-Box.

Accessories

The S2 Sensor/Transmitter has numerous accessories available to meet the individual workplace's needs. Such accessories include calibration adaptors, flow through adaptors, remote horns and lights, calibration kits, battery backups, splash guards, air aspirator adaptors or panels, and data loggers.

Each sensor comes standard with a one year warranty for materials and workmanship.

*Please note we can only ship RKI products to customers within the United States

Impact Personal Multi-gas Monitors

The Impact range of portable multi-gas monitors is able to monitor and display up to four gases simultaneously.

Using high specification flammable, oxygen and patented Surecell™ toxic sensors, our unique cartridge technology ensures safe, accurate and reliable measurements are always made.

Available in two configurations, the Impact and Impact Pro accepts either disposable and/or serviceable cartridges respectively, all of which are pre-calibrated and can be replaced in under one minute, so simplifying maintenance and minimising cost wherever possible. Compact and rugged these monitors are designed for tough working environments while being small, lightweight and unobtrusive, making them ideal for use in confined spaces where entry and exit may be difficult.

Designed to work how you want to; gas checks prior to entering a confined space can be carried out using a drop line, hand aspirator or via an optional built-in pump (supplied as standard on the Impact Pro) that turns on and off automatically when the sampling tube is connected.

Ultra-bright alarm lights and a powerful audible alarm, coupled with a periodic green flash and bleep provide user confidence that monitoring is always in operation and alarms are never missed. For noisy environments a vibrating alarm is included as standard on the Impact Pro. A large, multilingual, backlit display, with intuitive menu system simplifies use and minimises operator training.

Available for use with a wide range of accessories including the unique Enforcer calibration system and compliance friendly Safelink communication system, you can be sure that the Impact range of portable multigas monitors will be ready to protect you when most needed.

Reliable Operation

• Pre-calibrated plug-in sensor cartridge
• High specification sensors
• Patented Surecell™ toxic sensors
• Stable and accurate

Easy to Use

• One button on/off
• Multi-lingual, intuitive menu system
• On screen prompts guide user
• Built-in correction factors for flammable gases
• Minimal training required

Easy to Maintain

• Plug-in operation for all serviceable parts
• Cartridge replacement in less than one minute
• Re-calibration in less than two minutes when using Enforcer
• Minimised cost of ownership

Durable Housing

• Waterproof to IP67
• Rugged and impact resistant
• Built for everyday use

Alarm Indication

• 3 levels of instantaneous alarm, time weighted average alarms on toxic
• Periodic confidence flash and bleep
• Increasingly rapid flashing, ultra-bright alarm LEDs
• Powerful two tone audible alarm
• Vibrating alarm for noisy environments*
• Safelink communications*

User Friendly Pre-entry Check

• Peak hold function and drop line
• Hand aspiration
• Built-in automatic pump*
• Totally flexible

6307K Benchtop pH/Conductivity Meter Kit by Jenco

pH/Conductivity/Salinity/Temperature benchtop meter with dual LCD displays for conductivity and r pH/mV/temp. Features cell adjust and 4.01/7.00/10.01 buffer select.

Includes:

• 6307 Benchtop pH/Conductivity Meter
• 600P pH Electrode
• K=1.0 Cell
• 6230D115 AC Adapter

• Dual LCDs display pH, conductivity, or salinity, simultaneously with temperature.
• Accepts 2-wire and 4-wire conductivity cells with k=1 or k=5 cell constants for improved flexibility and accuracy.
• Auto or manual ranging of 4 conductivity ranges are available for improved usability.
• Convenient calibration with automatic buffer recognition of us or european pH buffer sets. quick one point conductivity calibration. calibration data is stored in memory and is ready for use on power up.
• Readings are automatically compensated for temperature (ATC). meter automatically switches into manual compensation when temperature probe is not present.
• Automatic lock mode and end point sensing are available to lock in stable readings.
• Intuitive operation with membrane keypad with tactile and audio feedback.
• Indication for electrode slope and electrode offset for optimized electrode maintenance.
• Splash resistant case is made with durable, reinforced plastic for added protection.
• RS-232 computer interface with software.
• BNC connector for pH/reference pH and mv.
• 8pin DIN connector for conductivity cell & 10k thermistor.
• Separate pin plug connector for reference pH.
• AC adaptor or battery power.