$750 - $1000

2106B2310 Sensepoint Hazardous Area Approved Gas Detector, HT Flammable Sensor (ATEX) M20 by Honeywell Analytics

The Sensepoint range of flammable, toxic and Oxygen gas detectors offer users a high quality, low cost solution to their industrial gas monitoring needs. Installation in potentially explosive atmospheres is made by the use of a suitable Ex d or Ex e approved junction box. The industry standard outputs from Sensepoint are connected to either a choice of Honeywell Analytics' controllers or 3rd party DCS/ PLC systems. Both flammable and toxic versions are certified to the latest ATEX/IECEx safety and performance standards.

The flammable detector is available in either % LEL or PPM detection range versions and provides an industry standard mV bridge output. Typical life expectancy is greater than 5 years, after which the detector is simply replaced with a new one.

The toxic detectors are supplied pre calibrated for easy installation and provide an industry standard 2 wire 4-20mA loop output. User connections are Ex d, while front end Intrinsic Safety (IS) design allows for easy exchange of the replaceable sensor while powered. IS design also removes the need for a sinter enabling very fast speed of response and detection of 'sticky' gases such as Chlorine and Ammonia.

Sensepoint has proven its suitability across a wide range of demanding applications by delivering high performance and reliability at an affordable cost.

Fit For Purpose

• Flammable, toxic and Oxygen versions available
• High performance, low cost
• Suitable for new and retro fit applications

Proven Sensor Technology

• Surecell™ electrochemical sensors
• Poison resistant catalytic bead
• Fast and reliable
• Typical 2 to 5 years operational life

ATEX/IECEx Certified

• Complies with the latest standards
• Hazardous area approval and performance
• IP65/67 for use in harsh environments

Easy to Use

• Factory set operation
• Simple to replace
• Minimal training required

Range of Accessories

• Weatherproof cap
• Flow adaptor
• Duct mounting kit
• Collecting cone

7020301 PCB EnviroGard 12T Soil Test Kit by Modern Water

Envirogard® is a rapid field enzyme immunoassay method for the analysis of soil remediation, assessment and industrial testing. It uses a coated tube technology to detect the analyte of concern.

Features:

• Convenient and rapid testing in the field or labatory
• Tests up to 10 samples at once
• Two detection levels of your choice are provided with each sample
• High level of accuracy
• EPA SW-846 Method #4020

Test result type

• Semi-quantitative or qualitative data
• Knowledge of specific aroclor(s) present will aid accuracy

Samples per kit

• Dependent on batch size and number of detection levels
• Each sample can be tested one at a time or in batches of two to ten samples

Assay range

• Soil: 0.5 ppm to 500 ppm with dilutions
• Wipes: 5.0 ug/100cm² to 5000 ug/100cm² with dilutions

Sample preparation

• Soil samples require prior extraction using the sample extraction kit (sold separately)
• The sample extraction kit provides materials for 12 soil sample extractions with methanol

Sampling time

• Approximately two minutes per sample plus assay run time of approximately 30 minutes

Basic Test Procedure

• Transfer soil or wipe to extraction jar
• Cap and shake for one minute
• Filter extracted sample
• Pipette and dilute samples with dilution ampule
• Transfer 1 ml of buffer to glass buffer tubes
• Pipette and transfer sample to buffer tubes
• Fit antibody coated tubes on buffer tubes; invert and mix;return to antibody coated tube
• Incubate for 10 minutes
• Connect antibody coated and conjugate tubes; invert and mix, return to antibody coated tube
• Incubate five minutes
• Wash antibody coated tubes vigorously four times
• Using a repeater pipette at setting two and 5 mL tip,transfer 200 uL substrateA to each tube
• Add 200 uL substrate B to each tube and mix
• Inclubate for 2.5 minutes
• Add 200 uL STOP to each tube
• Read tubes in photometer.Record data

Test kit components

• 48 antibody coated tubes and PCB enzyme conjugate vials
• 48 glass buffer tubes
• Substrate and stop solution reagents
• PCB standard
• Pipette tips and bulb pipettes
• Buffer
• Amber vials
• Wash solution
• 12 ampule crackers

Storage & precautions

• Shelf life is typically one year from date of manufacture, with specific kit expiration date information provided on product packaging.
• Store at ambient temperature 64° to 81°F (18° to 27°C)
• Kits must be brought to 64° to 81°F (18° to 27°C) before use
• Do not freeze test kit components

Required test materials

• PCB EnviroGard 12T accessory kit (6050400)
• PCB EnviroGard 12T accessory kit rental (Includes all equipment required to operate test and interpret results)(6997020)

Required test equipment

• PCB EnviroGard 12T soil test kit (7020301)
• PCB soil sample extraction kit (7020301EB)
• EnviroGard PCB wipe sample extraction kit (7020301WA)

Other recommended materials

• Absorbent paper
• Liquid waste container
• Disposable gloves
• Marker pen
• Liquid and solid waste containers

GS-CI-A-071-G Gasman Single Gas Monitor, 0-10ppm Ethylene Oxide, Rechargable Battery, Dutch Safe Area only by Crowcon

For over 40 years, Crowcon Detection Instruments has produced state of the art gas detection devices for personal and industrial use. Building upon their reputation for reliable and innovative gas monitoring products, Crowcon introduces the Gasman personal gas monitor. Its lightweight and compact design is convenient for jobsites where workers need not be weighed down by excessive bulk and equipment. The unit conveniently clips to a pocket or helmet and operates continuously.

The Gasman personal gas monitor has numerous convenient features such as:

• One button technology
• Backlit LCD display
• Durable polycarbonate casing
• Quick response triple alert system
• Compact and lightweight design

Easy to Use

The Gasman s true one button technology is an ideal and simple design. The large glove friendly button is mounted on the front of the unit for easy access and controls all of the unit s programmable features. Also on the front, the Gasman s easy to read backlit LCD screen indicates gas readings and the battery status. The simple screen provides a clear indication of the unit s operation status. It will also alert the user 30 days in advance of when a calibration test is due. With a simple and intuitive design, Crowcon has produced a gas detector that reduces the complexities of workplace safety, and ensures workers in a straightforward manner that their equipment is on and operational.

Triple Alarm System

This portable single gas detection system features a triple alarm system that is sure to alert the user and anyone in the vicinity. The visible alarm utilizes a dual red and blue flashing LED light, and the unit houses an internal vibrating alert system. These two indicators allow for visual recognition in loud environments and working conditions. The alarm system also features a programmable audible alarm at 95 decibels. The unit is capable of a variety of alarm tones, and users can select which tone may be best for the individual workplace setting. The triple alarm system with multiple sensory indicators is sure to be noticed in almost any work environment.

Specifications

The Gasman single gas monitor is lightweight and compact, weighing less than 135 grams and with dimensions of 90 x 48 x 24 mm. The unit is available with a wide variety of gas sensors which feature various detection and alarm levels. The unit also features a quick response time of 20 seconds for flammable and toxic gases or 10 seconds for oxygen. Its datalogging feature has approximately 900 hours of storage and all events are time stamped. The battery life for this unit is incredible with 12 hours of runtime on a Rechargeable battery battery or up to 2 years on a non-Rechargeable battery.

485P1-3 48" Galvanized Panel Fan, 5-Wing, 1 Hp, 3-Phase by Schaefer

Schaefer's galvanized steel panel fans combine low cost, high airflow and high air speeds for very high ROI livestock cooling. These fans are designed for agricultural livestock buildings requiring large volumes and velocities of air with a belt driven preference. Regardless of application, free stall barns, feed lines or holding pens, Schaefer offers a wide variety of galvanized panel fans to meet your specific needs. Ships fully assembled, complete with belt tensioner.

Features and Benefits

• Industry leading airflow and efficiency with airflows up to 40,000 cfm and efficiencies up to 40 cfm/watt
• Lab tested design for maximum performance and quiet operation
• Heavy gauge galvanized and powder coated steel components
• Thermally protected TEAO motors for long life
• Optional post and column mounts available
• Available in 24", 36", 48", 52" and 54" sizes
• 3-wing or 5-wing blade style
• Two year warranty
• Made in the USA

020-1111-0A0 QRAE II Multi-gas Diffusion Detector - LEL CSA-UL / O2 / H2S 100 ppm / CO / Li-Ion Rechargeable by RAE Systems

The QRAE II is a full-featured, compact, one- to four-sensor gas detector for oxygen, combustibles, hydrogen sulfide, or carbon monoxide. Key features include easy-to-change battery pack, a water-resistant case and a new state-of-the-art O2 sensor.

QRAE II Monitor Includes

• Monitor as specified
• Sensors as specified
• Calibration adapter and internal filters (diffusion only)
• Quick reference guide
• User manual and ProRAE Studio II Software Package for Windows® XP, Windows® Vista and Windows® 7
• Alkaline adapter
• Water trap filter (pump only)
• Rechargeable versions additionally offer: Charging/download cradle with computer interface cable, Universal adapter, Lithium-ion battery pack

Key Features

• Patented SPE O₂™ Oxygen sensor features: Lead-free design that complies with RoHS directive, Extended life resulting in low cost of ownership, Leak-free design, minimizing downtime
• Best EMI/RFI immunity technology, minimizing electromagnetic and radio interference
• Easy access to pump, sensors, filter and battery compartment
• IP-65 water-and dust-resistant case
• Strong, protective, concussion-proof designc
• Plug-in sensors: oxygen, combustibles, hydrogen sulfide, or carbon monoxide
• Intuitive simple-to-operate two-button user interface
• Multi-language support
• One-button calibration with auto-zero capability

Applications

• Emergency response
• Environmental
• Fire service
• Industrial safety
• Oil and gas applications

0563 6352 635-2 Compact Pro Thermohygrometer with Memory & Software by Testo

The instrument for measuring air moisture, material equilibrium moisture and pressure dewpoint in compressed air systems. Moisture characteristics can be recorded in the instrument memory and analysed and displayed in graphics or tables. Up to 3 temperature or humidity probes can be displayed in the testo 635-2 meter; data transmission is by radio i.e. wireless. Selectable user profiles, i.e. allocation of specific function buttons and menu-guide to an application enable intuitive operation. Material moisture can be displayed immediately on account of the special probe. Characteristics for different materials can be stored in ComSoft and transmitted to the instrument. testo 635 immediately displays the dewpoint difference between ambient air and the wall surface in the analysis of moisture on walls and ceilings. Precision probes up to -60°C tpd are available to check pressure dewpoint in compressed air systems. The humdity sensor developed by Testo has proven itself worldwide and has outstanding features in terms of precision, long-term stability, temperature resistance and robustness.

• Instrument memory for up to 10,000 readings
• PC software for analysis, filing and documentation of measurement data
• Measurement of air moisture, material equilibrium moisture, pressure dew point
• Radio probe for temperature and humidity
• Protection class IP54
• Direct display of material moisture due to freely settable characteristics curves (based on equilibrium humidity)
• Storage of single measurements or measurement series by measurement location
• Fast access to the most important functions via user profiles
• U-value probe connection option

GasAlertMicroClip X3 4-Gas Detector, O2/LEL/H2S/CO, Yellow, North America by BW Technologies

With that combination of benefits, it's no wonder the GasAlertMicroClip is the world's most popular multi-gas detector, serving as your trusted companion in hazardous environments - keeping you safe without weighing you down.

Plus, it's the first multi-gas detector with a rating of IP68 for unmatched water protection. So you can be confident it will stand up to challenging conditions.

Choose from two detectors, both with extended 18-hour battery runtime, one-button operation and Honeywell's rigorous approach to quality:

GasAlertMicroClip XL: low up-front cost with a two-year warranty.

GasAlertMicroClip X3: three-year warranty and a new oxygen sensor that extends overall operational life expectancy.

Use our unique advanced technology for safety, compliance and productivity.

• Advanced engineering for reliable battery performance
• Reflex Technology™ automated self-test function routinely checks the operating condition of the sensors to increase safety, up-time, and overall worker confidence
• Compact, lightweight and easy to use - no expertise required
• Flashing green IntelliFlash™ light for compliance at a glance

GasAlertMicroClip Standard Features:

• Guaranteed runtime for at least a 12-hour shift - down to -20°C - without compromising LEL detection of hydrogen, acetylene and other combustible gases
• Durable, rechargeable lithium polymer battery - tested to last in extreme environments
• Ergonomic and wearable - doesn't weigh you down
• Real-time gas concentrations shown on LCD
• Bright, wide-angle visual alarm bars
• IP68 rating ensures maximum protection against dust and water
• User-friendly, tamper-proof operation with just one button and intuitive LCD icons
• IntelliFlash™ light indicating detector has been bump tested and is monitoring correctly
• Self-test of sensors, battery status, circuit integrity and audible/visual alarms on startup
• Compatible with MicroDock II docking station for automated bump tests and calibration
• Compatible with Fleet Manager II software for reporting and fleet management
• Multi-language support in English, French, German, Spanish and Portuguese

New to GasAlertMicroClip X3:

• Five-year life expectancy - plus a three-year warranty
• An all-new oxygen sensor that operates consistently for five years - with no replacement costs for the life of the detector
• Superior cost of ownership - with minimized maintenance and maximized uptime

Part Number: MCX3-XWHM-Y-NA

Part Number: CG2E1058

MCX3-XU0M-Y-NA GasAlertMicroClip X3 3-Gas Detector, Combustible (% LEL, Unfiltered), Oxygen (O2), Carbon Monoxide (CO) - Yellow Housing, NA version (North America) by BW Technologies

With that combination of benefits, it's no wonder the GasAlertMicroClip is the world's most popular multi-gas detector, serving as your trusted companion in hazardous environments - keeping you safe without weighing you down.

Plus, it's the first multi-gas detector with a rating of IP68 for unmatched water protection. So you can be confident it will stand up to challenging conditions.

Choose from two detectors, both with extended 18-hour battery runtime, one-button operation and Honeywell's rigorous approach to quality:

GasAlertMicroClip XL: low up-front cost with a two-year warranty.

GasAlertMicroClip X3: three-year warranty and a new oxygen sensor that extends overall operational life expectancy.

Use our unique advanced technology for safety, compliance and productivity.

• Advanced engineering for reliable battery performance
• Reflex Technology™ automated self-test function routinely checks the operating condition of the sensors to increase safety, up-time, and overall worker confidence
• Compact, lightweight and easy to use - no expertise required
• Flashing green IntelliFlash™ light for compliance at a glance

GasAlertMicroClip Standard Features:

• Guaranteed runtime for at least a 12-hour shift - down to -20°C - without compromising LEL detection of hydrogen, acetylene and other combustible gases
• Durable, rechargeable lithium polymer battery - tested to last in extreme environments
• Ergonomic and wearable - doesn't weigh you down
• Real-time gas concentrations shown on LCD
• Bright, wide-angle visual alarm bars
• IP68 rating ensures maximum protection against dust and water
• User-friendly, tamper-proof operation with just one button and intuitive LCD icons
• IntelliFlash™ light indicating detector has been bump tested and is monitoring correctly
• Self-test of sensors, battery status, circuit integrity and audible/visual alarms on startup
• Compatible with MicroDock II docking station for automated bump tests and calibration
• Compatible with Fleet Manager II software for reporting and fleet management
• Multi-language support in English, French, German, Spanish and Portuguese

New to GasAlertMicroClip X3:

• Five-year life expectancy - plus a three-year warranty
• An all-new oxygen sensor that operates consistently for five years - with no replacement costs for the life of the detector
• Superior cost of ownership - with minimized maintenance and maximized uptime

Part Number: MCX3-XU0M-Y-NA

VN00421 X-am 2500 Multi-Gas Detector, LEL, O2, Akaline Battery Pack by Draeger

Draeger's X-am® 2500 accurately detects O₂, CO, NO₂, SO₂ and H₂S and is the only 1 4 gas monitor you need in industrial and refinery applications. The X-am® 2500 combines reliable sensor technology with long battery life and intuitive operation in an instrument that defines safety. It is approved for most markets including mining, oil & gas, chemical, fire and hazardous response, government and many other applications.

Matrix display

The X-am 2500 has a large, easy to read, liquid-crystal display. All gas readings are shown simultaneously and resize automatically depending on the number of sensors installed. When a gas alarm occurs, the reading for the sensor in alarm will be highlighted and will alternate with the alarm level indication of A1 or A2.

High capacity battery

The Draeger X-am 2500 can operate for more than 12 hours with either alkaline batteries or with rechargeable NiMH batteries. Depending on the requirements, the batteries can be charged either in the workshop or in a vehicle. Operating time without an Ex sensor installed is typically more than 250 hours.

X-dock compatibility

The X-am 2500 is compatible with Draeger's X-dock testing and calibration station. X-dock is Draeger's new solution for efficient maintenance and comprehensive equipment management. Used for functional testing and complete documentation, X-dock can complete bump tests in 8 to 15 seconds with more than 40% less gas consumption than competitive using several 500 — 550 mL/min of gas flow. The X-am 2500 is also compatible with the Draeger Bump Test Station.

Long-lasting, reliable sensor technology

The innovative, catalytic Ex sensor has a high degree of drift stability with a high resistance to silicone and hydrogen sulfide. The sensor boasts an expected service life of more than five years and is extremely sensitive to flammable gases and vapors. Further, the X-am 2500 is approved for measuring from methane to nonane, according to IEC/EN 60079-29-1.

Zone 0 approved

The Draeger X-am 2500 has Ex approval for zone 0 for user safety in areas subject to explosion hazard. Additionally, it is not sensitive to electromagnetic radiation, e.g. from wireless devices and is water and dust resistant in accordance with protection class IP 67.

Diffusion or pump

An optional external pump with a hose up to 45 m / 147 ft long is available for use in tanks and shafts or when searching for leaks. The switch from diffusion to pump operation can be handled quickly and easily without tools or screws.

Ergonomic and robust

The Draeger X-am 2500 is comfortably worn thanks to its low weight and ergonomic design and gas can enter the unit from above and from the front—even if the instrument is inside a pocket or if the front gas entry is accidentally covered.

The practical two button control panel and easy menu navigation allow for intuitive operation while the integrated protective rubber coating and sensors not sensitive to shock provide additional safety in case of impacts or vibrations.

Peak value functionality

The X-am 2500 can store the highest gas readings for the Ex and toxic gas sensors and the lowest reading for the O₂ sensor. These readings can be easily reset after a gas exposure without having to turn the monitor off and on.

1X-dock bump test stated times are typical results; stated gas consumption is based upon calibration gas flow of 0.3 L /minute using X-dock for bump test.

Xgard Gas Detectors

Crowcon is a global leader in designing and manufacturing gas detection technology and equipment. The company has been in operation for over 40 years and is consistently building upon its products. By integrating modern technology with the demands of the modern workplace, Crowcon has developed a line of gas detection devices and monitors that lead the competition. The Xgard range of gas detectors is a product of Crowcon s successful integration and technological advancements. With a wide range of sensor types and available accessories, the Xgard series is suitable for all worksites and is customizable enough to fit any needs.

Tough and reliable

The Xgard series of fixed point gas detectors is incredibly durable and reliable. The casings and materials, including weatherproof caps, are designed to protect the equipment from the harshest environments. The detectors are made from a variety of materials depending on the model: glass reinforced nylon, aluminum with polyester coating, and 316 stainless steel.

Variety of sensors

The fixed point gas detector offers a wide range of sensors for to suite almost all applications. The Xgard range of gas detectors is available in three models to meet varying worksite needs: flameproof, intrinsically safe, and safe area formats. Additionally, Xgard offers different types of fixed point gas detectors within these three models:

• Xgard Type 1- Intrinsically safe toxic and oxygen gas detectors
• Xgard Type 2- Flameproof toxic and oxygen gas detectors
• Xgard Type 3- Flameproof flammable gas detector
• Xgard Type 4- Flameproof high temperature flammable gas detector
• Xgard Type 5- Flameproof flammable gas detector with 4-20mA output
• Xgard Type 6- Flameproof thermal conductivity type gas detector
• Xsafe- Safe area flammable gas detector

Cost efficient and highly effective

With quick and easy installation and maintenance, the Xgard series is able to keep costs at a minimum. The replacement sensors, for example, are simple to replace by merely plugging them in. The replacement parts are also readily available and compatible with all Xgard models, thereby reducing the amount of required spare parts that are stored in the facility. Additionally, the sensors have two times the typical life spans of similar sensors in the industry. With a 2 year life span, worksites can expect to cut their sensor replacement costs in half. For worksites that require slightly more customization, Crowcon offers compatible accessories for the Xgard series such as sampling applications, remote gassing applications, spray deflectors, sun shields, weatherproof caps, collector cones, flow adapter, and accessories adapter.

Xgard also has flexible installation options. The unit is designed for either wall or ceiling mounts, and users will not need to purchase additional equipment for mounting. For more complex installation needs, users can purchase accessories.

Specifications

Each model is approximately the same size with dimensions of 6.1 x 6.5 x 4.3 inches and weighing approximately 1 or 2 pounds. The battery type, electrical output, and power requirements vary based on the sensor type. For a complete listing of gas sensors, types, and individual specifications, please see the product specifications listing.

Ranger EXP Digital Radiation Meter with External Probe by SE International

The Ranger EXP offers maximum performance in a lightweight, rugged solution for using your survey meter in the field. The Ranger EXP is designed specifically for individuals operating in tough environments. The small, handheld unit offers excellent sensitivity to low levels of alpha, beta, gamma, and x-rays. The digital readout is displayed with a red count light and a beeper sounds with each count detected. Other features include an adjustable timer, selectable alert, and with the free Observer USB Software Family, you can download your collected data, set alarms, and calibrate your meter!

GAXT-E-DL GasAlert Extreme Detector ETO Yellow by BW Technologies

Designed with durability and comfort in mind, the GasAlert Extreme reliably monitors for any single gas hazard within its wide range of available toxic gas models. With easy on/off operation, this single gas detector offers extended longevity with a two year fi eld-replaceable battery and sensor. Calibration is a simple automatic procedure and is compatible with BW's MicroDock II automatic test and calibration system. A wide range of user options, multilanguage display and datalogging functionality make the GasAlert Extreme an ideal solution for many applications.

• Direct, real-time readings on large LCD
• Operates through consecutive shifts - exceptional battery run-time
• Secure and accurate history with datalogging

Standard features of BW products:

• Continuous LCD shows real-time gas concentrations
• Compact and lightweight design makes it comfortable to wear
• Water-resistant
• Simple automatic calibration procedure; compatible with BW MicroDock II automatic test and calibration station
• Full function self-test of sensor, battery status, circuit integrity and audible/visual alarms on start up
• Bright wide-angled visual alarm bars
• Built-in concussion-proof boot

Additional GasAlert Extreme features:

• Equipped with internal vibrating alarm for high noise areas
• Secure and accurate history with datalogging
• Multi-language support in English, French, German, Spanish and Portuguese
• Tamper-proof settings with passcode protection

Part Number: GAXTEDL

PF3W7 Digital Flow Switch for Water, 3-Color Display, Integrated Display by SMC

Series PF3W digital flow switch is perfect for applications requiring a constantly monitored flow of cooling or cleaning water. The PF3W series has been improved both in design and operating performance over the PF2W flow switch. Depending on the selected model, the PF3W is up to 40% smaller in volume, offering improved piping space and flexibility. Designed to work with fluids up to 90°C, these switches incorporate a built-in temperature sensor so both flow and fluid temperature can be effectively monitored at the same time. Further improvements include the addition of 2 screens, incorporating 3-color numerical displays which can also be rotated in both clockwise and counter-clockwise directions, thereby offering even better display visibility during operation. Available as non-grease type and with analogue output if required, the PF3W meets IP 65 enclosure protection standards and is both RoHS and CE compliant.

• Digital flow switch for water applications
• Integrated display type
• Flow rate range: 0.5-4(L/min) ~ 10-100(L/min)
• 3-color, 2-screen display
• Port sizes: 3/8, 1/2, 3/4, 1

Product contains:

• 3-Color Digital Flow SWITCH for Water
• 11 (10 to 100 L/min)
• N (NPT)
• 10 (1)
• F (OUT1: PNP; OUT2: Analog 4 to 20 mA)
• T (Temperature Sensor)
• Lead Wire w/M8 Connector, 3m
• F (Instantaneous Flow Rate: Gal/min; Accumulated Flow: Gal: Temp: °F)

4210LED-12V-25 Single Lamp Area Light, Magnetic Swivel Mount, 25' Cable, 12V LED Bulb, 120VAC to 12VDC Power Box by Western Technology

As one of our 4000 series SITE LIGHTs, this portable light with a large handle and removable magnetic swivel mount comes standard with 25 ft of electric cable allowing for quick and sure placement. The 4210LED Mountable Work Light is the perfect choice for your temporary job site lighting needs.

Features

• Emitter Type: LED (PAR 38 LED Lamp)
• 2000 Lumens
• Brightness @ 48": 1970 LUX @ 41" Diameter
• Color Temperature: 5600K
• Power Consumption: ~25 Watts (PAR 38 LED Lamp)
• Voltage versatile: 12 to 24 Volts AC/DC or 115 Volts AC
• Durable polyurethane construction is naturally rust and corrosion resistant and is easily cleaned or decontaminated
• Length: 12"
• Width: 6 1/2"
• Height: 6 1/2"
• Weight: 8 1/4 lbs
• Portable light with large handle & removable magnetic swivel mount
• Quick & sure placement using 150 lb. pull industrial magnet
• Vibration/ impact resistant
• Remains cool to the touch during operation
• Uses Western Technology PAR 38 LED lamp
• Suitable for use in -25° to +120° ambient temperature
• Comes standard with 25 ft electric cable (longer lengths available upon request)

KEM25CLO Kemio Sensors, Free and Total Chlorine, 500pk by AquaPhoenix

Palintest Kemio Sensors, 500 pack

Free Chlorine, 0.02-10 mg/L
Total Chlorine, 0.05-75 mg/L

G02-B614-100 ToxiRAE Pro Personal Monitor, EC, CSA/UL, CL2, Datalogging, Wireless 900MHZ, Standard Accs by RAE Systems

The ToxiRAE Pro is the world's first wireless personal monitor for toxic gases and oxygen. The ToxiRAE Pro can detect a broad range of gases from carbon monoxide, hydrogen sulfide, and oxygen to ammonia, chlorine, and formaldehyde. The ToxiRAE Pro provides safety professionals wireless remote access to real-time instrument readings and alarm status for better visibility and faster incident response. The ToxiRAE Pro's intelligent interchangeable sensors store calibration data, which allows users to monitor for one gas one day and another gas the next, by simply swapping the sensors in the ToxiRAE Pro.

ToxiRAE Pro Comes with

• ToxiRAE Pro monitor with sensor as specified, alligator clip, protective rubber boot, and rechargeable battery installed
• Charging and PC communication cradle
• PC communication cable
• AC adapter (100 to 240 V, 50/60 Hz AC to 12 V DC)
• Calibration adapters
• Quick Start Guide
• CD with documentation
• ProRAE Studio II software for PC-based instrument configuration and data management
• Calibration card, quality certificate, and warranty/registration card

Key Features

• Wireless access to real-time instrument readings and alarm status from any location
• Unmistakable five-way local and remote wireless notification of alarm conditions
• Intelligent sensors store calibration data, so they can be swapped in the field
• Most electrochemical sensors are shared with MultiRAE family instruments
• Largest display in its class
• Continuous datalogging
• Easy to use
• Reliable, rugged, and intrinsically safe

Applications

• Agriculture
• Chemical
• Fire service / HazMat
• Food and beverage
• Oil and gas
• Pharmaceutical
• Pulp and paper
• Steel manufacturing
• Water and wastewater industries

G02-BF14-100 ToxiRAE Pro Personal Monitor, EC, CSA/UL, CO COMP, H2, Datalogging, Wireless 900MHZ, Standard Accs by RAE Systems

The ToxiRAE Pro is the world's first wireless personal monitor for toxic gases and oxygen. The ToxiRAE Pro can detect a broad range of gases from carbon monoxide, hydrogen sulfide, and oxygen to ammonia, chlorine, and formaldehyde. The ToxiRAE Pro provides safety professionals wireless remote access to real-time instrument readings and alarm status for better visibility and faster incident response. The ToxiRAE Pro's intelligent interchangeable sensors store calibration data, which allows users to monitor for one gas one day and another gas the next, by simply swapping the sensors in the ToxiRAE Pro.

ToxiRAE Pro Comes with

• ToxiRAE Pro monitor with sensor as specified, alligator clip, protective rubber boot, and rechargeable battery installed
• Charging and PC communication cradle
• PC communication cable
• AC adapter (100 to 240 V, 50/60 Hz AC to 12 V DC)
• Calibration adapters
• Quick Start Guide
• CD with documentation
• ProRAE Studio II software for PC-based instrument configuration and data management
• Calibration card, quality certificate, and warranty/registration card

Key Features

• Wireless access to real-time instrument readings and alarm status from any location
• Unmistakable five-way local and remote wireless notification of alarm conditions
• Intelligent sensors store calibration data, so they can be swapped in the field
• Most electrochemical sensors are shared with MultiRAE family instruments
• Largest display in its class
• Continuous datalogging
• Easy to use
• Reliable, rugged, and intrinsically safe

Applications

• Agriculture
• Chemical
• Fire service / HazMat
• Food and beverage
• Oil and gas
• Pharmaceutical
• Pulp and paper
• Steel manufacturing
• Water and wastewater industries

SPLCG1BARCXNZZ Sensepoint XCL Fixed Gas Detector, Bluetooth Connection, H2 1000ppm, mA/RLY, Charcoal by Honeywell Analytics

Sensepoint XCL is a fixed point gas leak detector that is designed to meet the needs of commercial and light industrial applications. With over 50 years experience in gas leak detection, Honeywell offers a flexible range of highly-reliable sensing devices to meet those needs.

• Quicker installation
• Rapid configuration
• Simple to operate
• Straightforward to maintain

Honeywell innovation enables customers to pair the gas detector with their mobile phone, and then use an app to perform many tasks related to installation, commissioning and maintenance.

Flexible Output Options

Sensepoint XCL is available with either mA loop analog output or Modbus RTU with the option for relays on both. The result is a flexible solution that can easily be incorporated into legacy systems as well as new installations.

Faster Installation

Everything you need for installation is in the box, including simple drilling templates.

Easy Control and Maintenance

Sensepoint XCL's smartphone interface makes for much faster calibration, configuration and bump tests. Inspecting the status and settings of individual Sensepoint XCL detectors is simple. Use the mobile app to:

• Read gas concentrations in real-time
• Reconfigure settings
• Check unit histories

Automated Reporting

Increase the efficiency of your operations and reduce administration time. The app and Sensepoint XCL provides easy access to diagnostic information and generates calibration reports at the touch of a screen.

Compatible System Controller

Touchpoint Plus is the perfect complement to Sensepoint XCL, providing an intuitive, easy to operate gas detection solution to meet the needs of your business.

Visual Integration

Sensepoint XCL is designed with the needs of building architects in mind. Clean aesthetics and a choice of colors mean that the detector is ideal for public spaces like lobbies and retail environments.

Typical Applications

• Kitchens and food processing
• Manufacturing facilities and factories
• Hospitals
• Retail sites
• Transportation and parking
• Laboratories
• Hotel and leisure
• Apartments, accommodation blocks and condominiums

Accessories

• Calibration cap / flow housing
• Duct mount kit for round or flat profile ducts

FEATURES & BENEFITS

• Choose from a range of mA or Modbus output versions for flexible system design to meet the customers requirements.
• Selectable source or sink current for analog output enables one detector to be suitable for both system configurations.
• Optional relay output for external control systems or alarming devices enables easy integration and local indication.
• The ingress protection of IP65 allows units to be mounted in wash down areas.
• Multi-color visual indicator to show status makes it easier to know the detector status immediately and identify detectors that require attention or are warning of danger.
• Gassing port for easier bump test of units installed in inaccessible locations. No need to purchase a separate accessory and thus saves money.
• Manage the detector without making a physical connection. Remove the need for physical access to hard-to-reach devices.
• Simplified maintenance with familiar smartphone technology saves money and time.