$750 - $1000

DO6400TC/T DO Sensor, 0-300%, PTFE, 10K across anode, TC= by Sensorex

The DO6400 & 7400 series dissolved oxygen sensors feature a large capacity electrolyte holder, positive fit, easy to replace membrane and dependable galvanic cell technology for long term deployment. The body design ensures a good grip when wet. Ideal for Aquaculture and wastewater monitoring applications, these sensors require minimal maintenance. PTFE or High-Density Polyethylene (HDPE) membranes are available. 2 Replacement membranes, installation tool and electrolyte are included. Additional maintenance parts are in convenient kits (see ordering information). Sensors with mV output as well as built-in 4-20mA output in 0-100% and 0-200% saturation range are available. In addition, Modbus-485 output versions with 0-100% or 0-300% range are available.

Digital Communication for More Process Visibility:

• Modbus and 4-20 mA output options now available
• Con guration and calibration can be done using web based software

Easy to Install and Maintain

• Membranes can be replaced quickly
• Designed to have good grip even when sensor is wet

Long Lasting Life

• Proven and dependable galvanic cell technology with large solution capacity
• Replacement membranes, electrolyte, and installation tool are included

2430K0001 705 Flammable Detector, SG16B Junction Box, WP by Honeywell Analytics

The Model 705 high temperature sensor has been specifically designed for the detection of combustible gases in high temperature hazardous area locations.

Typical applications include turbine enclosures and drying ovens used in solvent based printing and coating machines.

These applications require a sensor that provides reliable and stable detection allowing low level alarm settings across a wide temperature range. Utilizing a specially matched pair of Sieger poison resistant combustible gas detection elements, the Model 705 High Temperature Sensor has a very stable baseline allowing alarm trip points to be set as low as 5% LEL across a temperature range of -25°C to +150°C (-3°F to +302°F). The gas measuring range can be configured from 0-20% LEL up to 0-100% LEL depending on the type of controller used.

The detector elements are housed in a UL hazardous area approved explosion proof assembly, and provide an industry standard 3 wire mV bridge output which can be connected to a suitable control device or converted to an analog output signal via a field transmitter.

Excellent Performance

• Certified for hazardous location operation up to +150°C (+302°F)
• Alarm trip points as low as 5% LEL
• Fast speed of response
• Poison resistant detectors
• Low power consumption

Cost Effective

• Low cost disposable sensor
• Greater than 5 year typical operating life

Reliable Operation

• Specially matched 'Sieger' detectors provide highest stability
• Proven technology from the World leader in combustible gas detection

Flexibility

• Measuring ranges from 0-20% LEL to 0-100% LEL
• Wide range of accessories

Robust Construction

• UL approved explosion proof enclosure
• High grade Aluminum construction

GP-5001 Indicator / Alarm Unit, Combustible Gas, 0-100% LEL, (MUST SPECIFY GAS) by RKI Instruments

Features

• Compatible with RM-570A/580 series
• Bar meter and digital multi-indication
• High level of visibility
• Low power consumption
• Support RS-485 communication function
• RoHS Compliant
• Global standard

Applications

• LPG, LNG utilities
• Refineries
• Chemical plants
• Semi-conductor manufacturing plants
• Engineering, public works
• Power station
• Iron and steel works
• Automative Planting Processes

*Please note we can only ship RKI products to customers within the United States

T4-HOZA-FR T4 Personal Gas Monitor, 3 Gas - H2S, O2, CH4 % LEL, Alternate Alarm Levels / Certifications by Crowcon

T4 integrates innovative safety features and an intuitive, rugged design to provide advanced protection for those working in harsh environments. This portable multigas detector, which is exceptionally easy to use and service, protects against the four most prevalent gas hazards: carbon monoxide (CO), hydrogen sulphide (H₂S), flammable gases and oxygen (O₂) depletion.

Features

• TWA resume function - unique to T4, this innovative feature ensures toxic gas exposure is calculated accurately over an entire shift, even if T4 is switched off for a break or during travel to another site.
• 18 hour battery life - safely work multiple or longer shifts between charges, covered by the 18 hour battery life.
• Backlit display - large, clear display with backlight and option to flip the screen 180° for easy viewing while worn.
• Rugged design - with a thick anti-shock rubber casing and drop-tested to 13.1 feet on concrete, T4 provides dependable operation under the most demanding use.
• Water & dust-resistant to IP65 & IP67 - provides protection in the harshest environments.
• Dedicated sensors - one sensor for every gas ensures effective, fast and reliable detection.
• Positive safety indicator - a simple 'traffic light' status indicator which, at a glance, provides visual assurance of operational and compliance status to both users and supervisors. Green light - Working safely. Red light - Attention required
• Intrinsically safe - ATEX approved and UL Class 1 Div 1 for safe operation in a wide range of hazardous environments.
• Multiple alarms - audible 95dB alarm, bright red/blue LED's and vibrating alerts provide effective warning to gas hazards.
• Easy operation - large single button and intuitive menu system minimize training and allow easy operation while wearing gloves.

VTS-M1231300101 Ventis MX4 Multi-Gas Monitor, CH4 (0-5%), CO, H2S, O2, Li-ion, Auto Charger, Without Pump, Black, UL/CSA, English by Industrial Scientific

The Ventis® MX4 is a four-gas monitor with the portability and size of a single-gas monitor. Eliminate the need for extra monitors and transition seamlessly from personal monitoring to confined space entry with the Ventis® Slide-on Pump— ideal for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries.

• Detect up to four gases with a wide range of sensor options
• Select alarm set points, set latch alarms, disable instrument shutdown while in alarm, and more
• Save time and reduce human error with maintenance and usage data available from iNet Control software
• Available with or without an integral pump, or with the Ventis Slide-on Pump for ultimate flexibility
• Non-pumped instruments compatible with 12-hour, 18-hour, or 20-hour batteries

The Ventis® Slide-on Pump

The Ventis® Slide-on Pump is ideally suited for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries. Available in black or safety orange and powered by its own battery, the slide-on pump is compatible with the Ventis MX4 and Ventis® Pro5 Multi-Gas Monitor.

• Convenient Sampling – Sample draw distance of up to 50 feet provides convenient sampling in a wide range of applications
• Easy to Attach – No tools are required to attach or remove the Ventis Slide-on Pump to or from the monitor
• Uses Same Batterys and Chargers as Ventis – Monitor and pump each use the same batterys, and can easily be exchanged between instruments
• Flexible Battery Options – Three available battery options make this pump extremely flexible in the field

VPX-01002100G1C Ventis Pro Series, CO, Li-ion Ext Range, Desktop Charger, None, Black, China Ex, CPA, LENS Wireless, Chinese by Industrial Scientific

Detect up to five gases simultaneously with the rugged, wireless, Ventis® Pro5 Multi-Gas Monitor. With Ventis Pro5, safety goes beyond the gas detector whether you need team-based alarm sharing, remote monitoring with location details, or both. The monitor is also backed by a Guaranteed for Life™ warranty.

• Eliminate the need for two pieces of equipment by using Ventis Pro5 for personal monitoring and confined space entry.
• Train workers on one, multi-purpose gas monitor and reduce the risk and investment of having different devices in the field.
• Improve team and site safety by locally sharing alarms and gas readings between wirelessly connected Ventis Pro5 monitors.
• Get real-time location and alarm data directly from Ventis Pro5 gas monitors to a designated safety contact with the optional cellular or wi-fi battery pack.
• Reinforce safe behavior with programmable alarm action messages like "EVACUATE" or "VENTILATE" based on alarm level.
• Simplify the user experience with the ability to hide unnecessary screens based on user needs, role, industry, or site.

485P112-3 48" Galvanized Panel Fan, 5-Wing, 1-1 / 2 Hp, 3-Phase by Schaefer

Schaefer's galvanized steel panel fans combine low cost, high airflow and high air speeds for very high ROI livestock cooling. These fans are designed for agricultural livestock buildings requiring large volumes and velocities of air with a belt driven preference. Regardless of application, free stall barns, feed lines or holding pens, Schaefer offers a wide variety of galvanized panel fans to meet your specific needs. Ships fully assembled, complete with belt tensioner.

Features and Benefits

• Industry leading airflow and efficiency with airflows up to 40,000 cfm and efficiencies up to 40 cfm/watt
• Lab tested design for maximum performance and quiet operation
• Heavy gauge galvanized and powder coated steel components
• Thermally protected TEAO motors for long life
• Optional post and column mounts available
• Available in 24", 36", 48", 52" and 54" sizes
• 3-wing or 5-wing blade style
• Two year warranty
• Made in the USA

6302-2052 MGS-450 Gas Detector - IP66, 3 x Relays, Analog Output, Modbus Output, Audible & Visual Alarms - R600, 0-100% LEL, Infrared by Bacharach

Bacharach's MGS-400 Gas Detectors makes compliance with mechanical equipment room and refrigeration safety codes simple and easy, saving time and money on equipment and installation. Using the MGS-400 App, users can intuitively use, commission and maintain their gas detection system without the need for specialty training or tools. Pre-calibrated sensor modules simplify maintenance, take minutes to exchange and do not require the use of calibration gas. The MGS-400 sensors can trigger additional audio-visual alarms and act as a standalone gas detection system, or integrate easily into a BMS / BAS or with Bacharach's optional MGS-408 Gas Detection Controller.

Features

• Mobile App Interface
• Pre-calibrated Sensors
• Semi-automated Calibration
• Remote Sensor Option
• Temperature-Compensated Measurement
• Low Temperature Performance
• Digital Communications
• Analog Outputs
• Relay outputs
• Audio & Visual Alarms
• Multiple Cable Entries and Terminals

Benefits

• Quick, easy and intuitive commissioning, configuration and maintenance requires no special training. No tools required to set alarm levels and behavior
• Fast and easy sensor maintenance. Eliminates need for calibration gas.
• Easy calibration process with mobile app. Generate calibration certificates for documentation.
• Locate the sensor element in hard-to-reach areas and the base unit where convenient for electrical and communication wiring (MGS-460)
• Mitigates false alarms and optimizes accuracy in refrigeration applications.
• Suitable for use in cold rooms and freezers down to -40° F/C.
• Integrate with local BMS/BAS via Modbus RTU
• For current or voltage output to legacy systems (MGS-450/460)
• 3 relays available for alarm and fault events to active horn/strobes and ventilation (MGS-450, MGS-460)
• On-board alarm notification supports compliance with ASHRAE 15 / EN 378
• Quick and easy installation of all wiring; daisy-chain power and digital communications.

6302-0026 MGS-410 Gas Detector - IP66, Modbus Output, Audible & Visual Alarms - NH3, 0-100 ppm, Electro-Chemical by Bacharach

Bacharach's MGS-400 Gas Detectors makes compliance with mechanical equipment room and refrigeration safety codes simple and easy, saving time and money on equipment and installation. Using the MGS-400 App, users can intuitively use, commission and maintain their gas detection system without the need for specialty training or tools. Pre-calibrated sensor modules simplify maintenance, take minutes to exchange and do not require the use of calibration gas. The MGS-400 sensors can trigger additional audio-visual alarms and act as a standalone gas detection system, or integrate easily into a BMS / BAS or with Bacharach's optional MGS-408 Gas Detection Controller.

Features

• Mobile App Interface
• Pre-calibrated Sensors
• Semi-automated Calibration
• Remote Sensor Option
• Temperature-Compensated Measurement
• Low Temperature Performance
• Digital Communications
• Analog Outputs
• Relay outputs
• Audio & Visual Alarms
• Multiple Cable Entries and Terminals

Benefits

• Quick, easy and intuitive commissioning, configuration and maintenance requires no special training. No tools required to set alarm levels and behavior
• Fast and easy sensor maintenance. Eliminates need for calibration gas.
• Easy calibration process with mobile app. Generate calibration certificates for documentation.
• Locate the sensor element in hard-to-reach areas and the base unit where convenient for electrical and communication wiring (MGS-460)
• Mitigates false alarms and optimizes accuracy in refrigeration applications.
• Suitable for use in cold rooms and freezers down to -40° F/C.
• Integrate with local BMS/BAS via Modbus RTU
• For current or voltage output to legacy systems (MGS-450/460)
• 3 relays available for alarm and fault events to active horn/strobes and ventilation (MGS-450, MGS-460)
• On-board alarm notification supports compliance with ASHRAE 15 / EN 378
• Quick and easy installation of all wiring; daisy-chain power and digital communications.

6302-0040 MGS-410 Gas Detector - IP66, Modbus Output, Audible & Visual Alarms - CO, 0-500 ppm, Electro-Chemical by Bacharach

Bacharach's MGS-400 Gas Detectors makes compliance with mechanical equipment room and refrigeration safety codes simple and easy, saving time and money on equipment and installation. Using the MGS-400 App, users can intuitively use, commission and maintain their gas detection system without the need for specialty training or tools. Pre-calibrated sensor modules simplify maintenance, take minutes to exchange and do not require the use of calibration gas. The MGS-400 sensors can trigger additional audio-visual alarms and act as a standalone gas detection system, or integrate easily into a BMS / BAS or with Bacharach's optional MGS-408 Gas Detection Controller.

Features

• Mobile App Interface
• Pre-calibrated Sensors
• Semi-automated Calibration
• Remote Sensor Option
• Temperature-Compensated Measurement
• Low Temperature Performance
• Digital Communications
• Analog Outputs
• Relay outputs
• Audio & Visual Alarms
• Multiple Cable Entries and Terminals

Benefits

• Quick, easy and intuitive commissioning, configuration and maintenance requires no special training. No tools required to set alarm levels and behavior
• Fast and easy sensor maintenance. Eliminates need for calibration gas.
• Easy calibration process with mobile app. Generate calibration certificates for documentation.
• Locate the sensor element in hard-to-reach areas and the base unit where convenient for electrical and communication wiring (MGS-460)
• Mitigates false alarms and optimizes accuracy in refrigeration applications.
• Suitable for use in cold rooms and freezers down to -40° F/C.
• Integrate with local BMS/BAS via Modbus RTU
• For current or voltage output to legacy systems (MGS-450/460)
• 3 relays available for alarm and fault events to active horn/strobes and ventilation (MGS-450, MGS-460)
• On-board alarm notification supports compliance with ASHRAE 15 / EN 378
• Quick and easy installation of all wiring; daisy-chain power and digital communications.

61-0207-02 Sensor, IR Carbon Dioxide (CO2) 0-5000 ppm, Explosion Proof Direct Connection, 3 / 4 inch NPT Conduit Mounting by RKI Instruments

When working on potentially hazardous jobsites, safety managers should look for workplace safety solutions that are dependable and steadfast. When lives are on the line, a workplace cannot afford subpar safety products. That is why, at RKI Instruments, workplace safety is a top priority. Their Research and Development team work daily to integrate the latest technology with the best industry practices. With a reputation for excellent products, RKI Instruments introduces the latest in direct connect sensor technology. Designed for use in Class 1, Division 2 hazardous environments, the Direct Connect Sensors are designed specifically for RKI Beacon 110, 200, and 410 controllers.

Direct Connect Sensors

The RKI Direct Connect Sensors series gas sensors are state of the art gas detection sensors available for LEL, H2 Specific LEL, LEL IR, Oxygen, H2S, CO, CO2, and a variety of toxic gases. To use the Direct Connect Sensors, they can be used for remote detection by mounting them onto explosion proof junction boxes, or they can mount directly onto controllers and be used as a completely standalone system. Their unique plugin design allows for a quick and easy tool free installation on jobsites.

Detection solutions for a variety of hazardous environments

The Direct Connect Sensors are designed to be use in both indoor and outdoor settings. Additionally, some of the sensors are available in explosion proof models. The explosion proof models utilize a patented coating which serves double duty as also being water repellant. Users can also purchase splash guards to protect the sensors from very wet conditions.

Sensor Technology

Each sensor is crafted with stainless steel and housed in cast aluminum (stainless steel housing is available for some sensors). The Direct Connect Sensors are available in 2 forms: explosion proof and non-explosion proof. The explosion proof sensors are available as catalytic sensors for LEL, and LEL H2 specific. For hydrogen sulfide and carbon monoxide, the sensors utilize electrochemical technology which provides incredibly specific accuracy and quick response. Oxygen sensors work with galvanic technology, and infrared sensors for methane, hydrocarbons, and carbon dioxide. Non-explosion proof uses a galvanic sensor for oxygen; electrochemical sensors for hydrogen sulfide, carbon monoxide and other toxic gases; and infrared for carbon dioxide. Both explosion proof and non-explosion proof have 1 year warranties for materials and craftsmanship.

Specifications

The response times are under 30 seconds for all gases except hydrogen sulfide and carbon monoxide in the non-explosion versions (with a response time of 35 seconds) and non-explosion proof model sensor for toxic gases which has a 60 second response time. The life expectancy of all sensors are between 2 and 5 years.

The Direct Connect Sensors are compatible with several RKI Industries' accessories including calibration adaptors, flow through adaptors, remote horns and lights, calibration kits, battery backups, splash guards, air aspirator adaptors, and dataloggers.

*Please note we can only ship RKI products to customers within the United States

45MJH2A1STAA Stenner Classic Series Peristaltic Pump, 10 GPD, 100 PSI, Tube 2 by Quantrol

Features

• Advantages of Stenner peristaltic pumps on page 1
• Fast tube replacement without tools with patented QuickPro® pump head
• Adjustable models: External adjustable dial ring on feed rate control; 20:1 turndown, 2.5% increments
• Single head models: Available as Tank Systems: 7.5, 15, 30 gallon; Fixed output pump can be utilized for proportional dosing, refer to pages 54-57
• Components are interchangeable between models
• Tank System ships pre-assembled for quick installations

VTS-LG234100201 Ventis MX4 Multi-Gas Monitor, LEL (CH4), CO/H2 Low, H2S, O2, Slim Extended Li-ion Battery, Desktop Charger, Without Pump, Black, ATEX/IECEX, English by Industrial Scientific

The Ventis® MX4 is a four-gas monitor with the portability and size of a single-gas monitor. Eliminate the need for extra monitors and transition seamlessly from personal monitoring to confined space entry with the Ventis® Slide-on Pump— ideal for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries.

• Detect up to four gases with a wide range of sensor options
• Select alarm set points, set latch alarms, disable instrument shutdown while in alarm, and more
• Save time and reduce human error with maintenance and usage data available from iNet Control software
• Available with or without an integral pump, or with the Ventis Slide-on Pump for ultimate flexibility
• Non-pumped instruments compatible with 12-hour, 18-hour, or 20-hour batteries

The Ventis® Slide-on Pump

The Ventis® Slide-on Pump is ideally suited for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries. Available in black or safety orange and powered by its own battery, the slide-on pump is compatible with the Ventis MX4 and Ventis® Pro5 Multi-Gas Monitor.

• Convenient Sampling – Sample draw distance of up to 50 feet provides convenient sampling in a wide range of applications
• Easy to Attach – No tools are required to attach or remove the Ventis Slide-on Pump to or from the monitor
• Uses Same Batterys and Chargers as Ventis – Monitor and pump each use the same batterys, and can easily be exchanged between instruments
• Flexible Battery Options – Three available battery options make this pump extremely flexible in the field

OX-5002 Indicator / Alarm Unit, Oxygen (4-20mA) by RKI Instruments

Features

• Compatible with RM-570A/580 series
• Bar meter and digital multi-indication
• High level of visibility
• Low power consumption
• Support RS-485 communication function
• RoHS Compliant
• Global standard

Applications

• LPG, LNG utilities
• Refineries
• Chemical plants
• Semi-conductor manufacturing plants
• Engineering, public works
• Power station
• Iron and steel works
• Automative Planting Processes

*Please note we can only ship RKI products to customers within the United States

VTS-K0231101204 Ventis MX4 Multi-Gas Monitor, LEL (Pentane), H2S, O2, Li-ion, Desktop Charger, Without Pump, Orange, ATEX/IECEX, German by Industrial Scientific

The Ventis® MX4 is a four-gas monitor with the portability and size of a single-gas monitor. Eliminate the need for extra monitors and transition seamlessly from personal monitoring to confined space entry with the Ventis® Slide-on Pump— ideal for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries.

• Detect up to four gases with a wide range of sensor options
• Select alarm set points, set latch alarms, disable instrument shutdown while in alarm, and more
• Save time and reduce human error with maintenance and usage data available from iNet Control software
• Available with or without an integral pump, or with the Ventis Slide-on Pump for ultimate flexibility
• Non-pumped instruments compatible with 12-hour, 18-hour, or 20-hour batteries

The Ventis® Slide-on Pump

The Ventis® Slide-on Pump is ideally suited for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries. Available in black or safety orange and powered by its own battery, the slide-on pump is compatible with the Ventis MX4 and Ventis® Pro5 Multi-Gas Monitor.

• Convenient Sampling – Sample draw distance of up to 50 feet provides convenient sampling in a wide range of applications
• Easy to Attach – No tools are required to attach or remove the Ventis Slide-on Pump to or from the monitor
• Uses Same Batterys and Chargers as Ventis – Monitor and pump each use the same batterys, and can easily be exchanged between instruments
• Flexible Battery Options – Three available battery options make this pump extremely flexible in the field

VTS-K1231000101 Ventis MX4 Multi-Gas Monitor, LEL (Pentane), CO, H2S, O2, Li-ion, No Charger, Without Pump, Black, UL/CSA, English by Industrial Scientific

The Ventis® MX4 is a four-gas monitor with the portability and size of a single-gas monitor. Eliminate the need for extra monitors and transition seamlessly from personal monitoring to confined space entry with the Ventis® Slide-on Pump— ideal for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries.

• Detect up to four gases with a wide range of sensor options
• Select alarm set points, set latch alarms, disable instrument shutdown while in alarm, and more
• Save time and reduce human error with maintenance and usage data available from iNet Control software
• Available with or without an integral pump, or with the Ventis Slide-on Pump for ultimate flexibility
• Non-pumped instruments compatible with 12-hour, 18-hour, or 20-hour batteries

The Ventis® Slide-on Pump

The Ventis® Slide-on Pump is ideally suited for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries. Available in black or safety orange and powered by its own battery, the slide-on pump is compatible with the Ventis MX4 and Ventis® Pro5 Multi-Gas Monitor.

• Convenient Sampling – Sample draw distance of up to 50 feet provides convenient sampling in a wide range of applications
• Easy to Attach – No tools are required to attach or remove the Ventis Slide-on Pump to or from the monitor
• Uses Same Batterys and Chargers as Ventis – Monitor and pump each use the same batterys, and can easily be exchanged between instruments
• Flexible Battery Options – Three available battery options make this pump extremely flexible in the field