$750 - $1000

6759 Umbrella, 59" X 59", Blackout Shade Material and V-Cup Mount by Pelsue

The Pelsue Floating Umbrella is designed as a portable shelter for situations where traditional work umbrellas aren't practical. This new umbrella design requires only a smooth clean surface for setup, making it perfect for tight spaces such as those found around Charles cabinets (like those commonly housing telecommunications equipment and other utilities). Thanks to the design of the suction cups it's also possible to attach the umbrella to surfaces that aren't perfectly flat, such as the side of work vehicles and trucks.If you are looking for shade or protection from inclement weather the Floating Umbrella has you covered. Coverage on the with the Floating Umbrella is about 50% greater than the Floating Tent, making it ideal for providing shade. Please note that the umbrella support structure is the same as that sold with the floating tent. You can easily switch out the top you are using should weather conditions change. The suction cups used here are pump operated for a strong hold, our current record is 6 hours on a smooth clean surface.

If you are worried about protection from more severe weather, consider Pelsue's Floating Tent. With 60' roll down sides it's capable of providing 360 degrees of protection.

Why suction cups and not magnets?

Suction cups let the umbrella work on almost any smooth surface, magnets require that the surface is magnetic (generally made of metal). Even with powerful magnets such as those made from neodymium, the surface may not be strongly attract the magnet. Magnets that aren't sufficiently powerful may also slide on the surface increasing the risk of injury. Powerful magnets are also dangerous in their own right. They may crush or pinch the unprepared if they are attracted to a surface. Suction cups are less prone to sliding and spinning, and can't practically cause crushing injuries.

Floating Tent Features

• Adjustable support with three joints to insure versatility in any location. Includes two hinge joints (base can be rotated in two axes), and a ball joint at the top.
• Water/Fire/UV resistant fabric for all portions of the tent.
• Non-Rusting and Rust resistant components for support structure.
• Dual Pump operated suction cups, with hold indicator on pump.
• Carrying case.

9506P Adjustable Hardwood Plank, Heavy Duty, 6' to 9.5' Long, 500 lb Rating by Pelsue

Manhole scaffold planks are constructed from strong hardwood with heavyduty, steel hardware and bolt through construction. Safety latches are included on expandable units at both ends to prevent accidental opening.

DSP-A1 Wall Mounted Plate/Sleeve 90 Degree Inside Mount, Powder Coated Steel by Pelsue

Permanent Mount Sleeves

• Available in electroless nickel plated steel, zinc plated, galvanized or stainless steel
• ABS liners with PVC slip plates
• Accepts up to 48" offset masts
• Sleeve is always on site
• Inside sleeve diameter 3.0680"
• Liners and sleeves are replaceable
• Allows masts to pivot 360°
• Drain holes eliminate water buildup
• Friction bearing is replaceable

Corner Mounted

Inside 90° angle. The corner mount is anchored by bolts to reinforced truck bumpers, walls, etc. Please contact Pelsue for specific installation requirements. Zinc plated steel.

DSP-A2 Wall Mounted Plate/Sleeve 90 Degree Outside Mount, Powder Coated Steel by Pelsue

Permanent Mount Sleeves

• Available in electroless nickel plated steel, zinc plated, galvanized or stainless steel
• ABS liners with PVC slip plates
• Accepts up to 48" offset masts
• Sleeve is always on site
• Inside sleeve diameter 3.0680"
• Liners and sleeves are replaceable
• Allows masts to pivot 360°
• Drain holes eliminate water buildup
• Friction bearing is replaceable

Corner Mounted

Inside 90° angle. The corner mount is anchored by bolts to reinforced truck bumpers, walls, etc. Please contact Pelsue for specific installation requirements. Zinc plated steel.

DSS-C1 Flush Floor Mount Sleeve for Fresh Pour Concrete, Stainless Steel by Pelsue

Permanent Mount Sleeves

• Available in electroless nickel plated steel, zinc plated, galvanized or stainless steel
• ABS liners with PVC slip plates
• Accepts up to 48" offset masts
• Sleeve is always on site
• Inside sleeve diameter 3.0680"
• Liners and sleeves are replaceable
• Allows masts to pivot 360°
• Drain holes eliminate water buildup
• Friction bearing is replaceable

Flush Floor Mounted

Placed in fresh concrete, this sleeve mounts flush with the floor and is great for high traffic areas where trip hazards are a concern. Please contact Pelsue for specific installation requirements.

DSS-F2 Floor Mounted Center Baseplate/Sleeve, Stainless Steel by Pelsue

Permanent Mount Sleeves

• Available in electroless nickel plated steel, zinc plated, galvanized or stainless steel
• ABS liners with PVC slip plates
• Accepts up to 48" offset masts
• Sleeve is always on site
• Inside sleeve diameter 3.0680"
• Liners and sleeves are replaceable
• Allows masts to pivot 360°
• Drain holes eliminate water buildup
• Friction bearing is replaceable

Floor Mounted

The floor mount is anchored by bolts, or it welds to a variety of surfaces such as floors, truck beds, catwalks, etc. Contact Pelsue for specific installation requirements.

DSS-F3 Flush Floor Mount Sleeve for Existing Concrete, Stainless Steel by Pelsue

Permanent Mount Sleeves

• Available in electroless nickel plated steel, zinc plated, galvanized or stainless steel
• ABS liners with PVC slip plates
• Accepts up to 48" offset masts
• Sleeve is always on site
• Inside sleeve diameter 3.0680"
• Liners and sleeves are replaceable
• Allows masts to pivot 360°
• Drain holes eliminate water buildup
• Friction bearing is replaceable

Flush Floor Mounted

Placed in fresh concrete, this sleeve mounts flush with the floor and is great for high traffic areas where trip hazards are a concern. Please contact Pelsue for specific installation requirements.

DSS-W1 Wall Mounted Plate/Sleeve, Stainless Steel by Pelsue

The wall mount is anchored by bolts or welds to truck bumpers, tank walls, sides of catwalks, meter pits, clarifiers, etc. Please contact Pelsue for specific installation requirements.

PSRL1125-SS Self Retracting Lifeline with 25ft SS Cable and Carabiner by Pelsue

Three-way recovery units & Self Retracting Lifelines are designed for use by construction workers, utilty personnel, & maintenance repair employees needing on-the-job fall protection. The stopping distance for all models is less than 2'. These units are also used in confined spaces such as manholes, tanks, vaults, and other confined areas, where fall-arrest and retrieval rescue are extremely important.

As a general rule, OSHA requires the use of fall protection for anyone working six or more feet above the base level of any work area (OSHA 1926.501).

When entering a confined space by ladder or other fixed structure, or while being lowered mechanically by a man-rated winch, a worker must be attached to an independent lifeline for adequate fall protection.

Self Retracting Lifelines will only arrest a fall, they do not provide retrieval capabilities. The three-way recovery unit can be used for fall protection as well as retrieval if an emergency should occur.

Can be mounted to the Davit Retrieval System or Tripod.

Under no circumstances shall the three-way be used for routine raising and lowering (use a man-rated PH series hoist for raising and lowering).

Features

• Arrest Distance within 2 feet
• Stress indicator to warn user that unit has arrested a fall
• 3/16" galvanized steel cable, stainless steel cable, Technora rope, or Webbing
• Cable Length: 25-65 ft. Webbing Length: 20-30 ft.
• Internal components made of bronze, stainless steel and aluminum
• Cast Aluminum housing protected with zinc plating
• Working Load: 310 lbs.
• Self-retracting lifelines require a carabiner for attachment to anchorage.

PSRL1125-TR Self Retracting Lifeline with 25ft Technora Rope and Carabiner by Pelsue

Three-way recovery units & Self Retracting Lifelines are designed for use by construction workers, utilty personnel, & maintenance repair employees needing on-the-job fall protection. The stopping distance for all models is less than 2'. These units are also used in confined spaces such as manholes, tanks, vaults, and other confined areas, where fall-arrest and retrieval rescue are extremely important.

As a general rule, OSHA requires the use of fall protection for anyone working six or more feet above the base level of any work area (OSHA 1926.501).

When entering a confined space by ladder or other fixed structure, or while being lowered mechanically by a man-rated winch, a worker must be attached to an independent lifeline for adequate fall protection.

Self Retracting Lifelines will only arrest a fall, they do not provide retrieval capabilities. The three-way recovery unit can be used for fall protection as well as retrieval if an emergency should occur.

Can be mounted to the Davit Retrieval System or Tripod.

Under no circumstances shall the three-way be used for routine raising and lowering (use a man-rated PH series hoist for raising and lowering).

Features

• Arrest Distance within 2 feet
• Stress indicator to warn user that unit has arrested a fall
• 3/16" galvanized steel cable, stainless steel cable, Technora rope, or Webbing
• Cable Length: 25-65 ft. Webbing Length: 20-30 ft.
• Internal components made of bronze, stainless steel and aluminum
• Cast Aluminum housing protected with zinc plating
• Working Load: 310 lbs.
• Self-retracting lifelines require a carabiner for attachment to anchorage.

PT5 Ultrapen PT5: Dissolved Oxygen & Temperature Tester (Myron L) by AquaPhoenix

This pocket pen tester is designed to measure dissolved oxygen and temperature

QT-XU00-A-B-NA GasAlertQuattro 2-Gas Detector, Combustible (% LEL, Unfiltered), Oxygen (O2), Alkaline Version - Black Housing, NA version (North America) by BW Technologies

BW Technologies by Honeywell introduces an industry leader in design simplicity and user friendliness. The Gas Alert Quattro multigas detector is backed with years of research and development. The design pays particular attention to the needs of users when on the worksite, and eliminates unnecessary design elements that distract users and complicate equipment training. With this simple and easy to read gas detection system, safety managers can reduce training time and costs with confidence.

User Friendly Features

Alarms and Automatic Tests

Specifications & Compatible Accessories

BW Technologies by Honeywell

Part Number: QT-XU00-A-B-NA

QT-XU00-A-Y-NA GasAlertQuattro 2-Gas Detector, Combustible (% LEL, Unfiltered), Oxygen (O2), Alkaline Version - Yellow Housing, NA version (North America) by BW Technologies

BW Technologies by Honeywell introduces an industry leader in design simplicity and user friendliness. The Gas Alert Quattro multigas detector is backed with years of research and development. The design pays particular attention to the needs of users when on the worksite, and eliminates unnecessary design elements that distract users and complicate equipment training. With this simple and easy to read gas detection system, safety managers can reduce training time and costs with confidence.

User Friendly Features

Alarms and Automatic Tests

Specifications & Compatible Accessories

BW Technologies by Honeywell

Part Number: QT-XU00-A-Y-NA

QT-XUHM-R-B-AU GasAlertQuattro 4-Gas Detector, Combustible (% LEL, Unfiltered), Oxygen (O2), Hydrogen Sulfide (H2S), Carbon Monoxide (CO), Rechargeable Version - Black Housing, AU version (Australia) by BW Technologies

BW Technologies by Honeywell introduces an industry leader in design simplicity and user friendliness. The Gas Alert Quattro multigas detector is backed with years of research and development. The design pays particular attention to the needs of users when on the worksite, and eliminates unnecessary design elements that distract users and complicate equipment training. With this simple and easy to read gas detection system, safety managers can reduce training time and costs with confidence.

User Friendly Features

Alarms and Automatic Tests

Specifications & Compatible Accessories

BW Technologies by Honeywell

Part Number: QT-XUHM-R-B-AU

QT-XUHM-R-B-CN GasAlertQuattro 4-Gas Detector, Combustible (% LEL, Unfiltered), Oxygen (O2), Hydrogen Sulfide (H2S), Carbon Monoxide (CO), Rechargeable Version - Black Housing, CN version (China/New Zealand) by BW Technologies

BW Technologies by Honeywell introduces an industry leader in design simplicity and user friendliness. The Gas Alert Quattro multigas detector is backed with years of research and development. The design pays particular attention to the needs of users when on the worksite, and eliminates unnecessary design elements that distract users and complicate equipment training. With this simple and easy to read gas detection system, safety managers can reduce training time and costs with confidence.

User Friendly Features

Alarms and Automatic Tests

Specifications & Compatible Accessories

BW Technologies by Honeywell

Part Number: QT-XUHM-R-B-CN