$300 - $400

1309A0039 E3Point Gas Monitor, Hydrogen (H2); -40° to 50°C (-40° to 122°F) by Honeywell Analytics

Toxic/combustible gas monitor that makes a commercial operation run more intelligently to protect people, property and the bottom line.

Product Overview:

E3Point is capable of detecting the widest range of toxic and combustible gases found in commercial building spaces and outbuildings, including CO, NO2, O2, H2, H2S, CH4 and C3H8. It can be used as a standalone unit with single or dual-gas detection (i.e. using a remote sensor) or deployed as a networkable device (interoperable with BACnet, Modbus or other Building Automation System): E3Point also functions with existing controller-based gas monitoring systems and wired-wireless gas monitoring system components.

E3Point uses Demand Control Ventilation—through relays, Building Automation System (BAS) or controller—to increase energy savings, extend fan life and align with green building best practices. In its network configuration, E3Point also optimizes HVAC, fire/smoke, surveillance and other building systems performance.

Intelligent product design reduces the unit's cost of ownership while increasing flexibility of application. Smart sensors are pre-calibrated, auto-configure upon set-up and operate continuously on patented Reflex© technology which continuously monitors sensor cell condition and alerts user to fault status. The plug-n-play sensor cartridge, user-friendly menu and wiring options simplify installation and maintenance, and reduce the cost of gas monitoring over the life of the unit.

Flexible Operation:

• Comes in standalone, standalone with remote (dual gas mode) or network versions
• Connects to analog or digital systems
• Works with virtually any BAS including BACnet and Modbus
• Connects to wired or wireless system (via 301CW wireless controller)
• Wall or duct mount
• Factory-calibrated cartridges

Cost Effective:

• Saves energy through Demand Control Ventilation (DCV)
• Simplifies installation/maintenance through plug-n-play sensor
• Remote sensor option provides dual gas monitoring (standalone version only)
• Optimizes BAS, fire, ventilation and other security systems

Versatile Communications:

• Works through BAS to improve fault diagnostics and collect data on gas concentration levels, sensor condition, etc.
• Couple with 301C to log data and daisy-chain up to 96 E3Point units

Advanced Sensing Technology:

• Detects CO, NO2, O2, H2, H2S, CH4, C3H8
• Advanced electrochemical (for toxic gases)and catalytic bead (for combustible gases) sensor performance
• Uses patented Reflex® and smart cartridge technologies

Electrical Certifications:

• US (ANSI/UL 61010-1)
• Canada (CSA C22.2 No. 61010-1)

Features & Benefits:

• Standalone, standalone with remote (dual gas mode) or network versions available
• Saves energy through Demand Control Ventilation

Quick Specs:

• Complete toxic and combustible gas detection system with onboard sounder
• Available in single point or dual gas options
• Analog 4-20 mA or Digital outputs (Bacnet, Modbus, and Lonworks)

*Please note we can only ship RKI products to customers within the United States

Part Number: 66L-439

*Please note we can only ship RKI products to customers within the United States

GHS1021 SDS Station with Binder (18" x 24"), English/French by GHS Safety

GHS Safety Data Sheet Information Station provides a central place to easily access all S.D.S. sheets for your plant or office. The Station comes with a sturdy metal pocket designed to hold the included binder. The mounting board is constructed of 1/4" plastic with 4 mounting holes to provide easy mounting and years of durability. Each station comes with 2 standard 3 ring SDS printed binders with A Z alphabetical dividers to sort all of your Safety Data Sheets.

The mounting board is constructed of 1/4" plastic with 4 mounting holes to provide easy installation and years of durability. 24" x 36"

English / French

Part Number: G10675PN

ADF25A Differential Probe by Test Products International

Selecting the correct oscilloscope probe ensures accuracy and can improve the performance of your test instrument. TPI offers a wide range of high quality oscilloscope probes designed to meet the most demanding applications.

The IP series monolithic probes have switchable attenuation and are available in 60 and 250MHz. These probes are ideal for technicians that need a basic oscilloscope probe.

The slimline design P and SP series probes are available in fixed or switchable attenuation. These series of probes are perfect for the technician needing additional features such as replaceable cable and interchangeable probe tip. The compensation adjustment for these probes is located in the BNC to eliminate noise pickup.

TPI also offers three models of high voltage differential probes all with high common mode rejection, wide bandwidth, and fast rise times. Differential probes enable the viewing of signals not referenced to earth ground and provide better performance than a matched pair of single ended oscilloscope probes when measuring these types of signals.

Several important factors must be taken into account when selecting the proper probe.

• The probe should have sufficient bandwidth and rise time for the test instrument and application. Choose a probe with at least an equal bandwidth as the scope it will be used with. For best performance a probe with twice the bandwidth as the scope should be selected
• For oscilloscope probes, the input capacitance of your oscilloscope should be within the compensation range specification of the probe. In addition, if your oscilloscope has readout function, select a probe with this capability
• For differential probes, make sure the maximum differential voltage is adequate for your application and the common mode rejection specification meets the requirements of the tests being performed.

Features

• Attenuation: Ratio of the output signal to the input signal. Attenuation should remain constant decreasing by 3dB only as the frequency increases to the maximum bandwidth.
• Bandwidth: The maximum -3dB frequency that can be expected.
• Cable Length: Length of the cable from the end of the probe to the end of the connector. It is important to use a probe with just enough cable length for your needs. Long cables increase the capacitance and propagation delay of the probe.
• Compensation Range: The range a probe can be compensated to match the input capacitance of the test equipment it is being used with.
• IEC 1010: Probes with the IEC 1010 category rating have been designed for safety.
• Input Impedance: The total resistance and capacitance as measured at the tip of the probe. This specification is used to define the loading effect of a probe. At frequencies under 1MHz the input resistance of the probe will have the most influence. At higher frequencies the input capacitance will have the most influence.
• Max Input Voltage: The maximum voltage the probe can be used at.
• Max Differential Voltage: The maximum differential voltage that can be measured by a differential probe
• Readout: Probes with this capability are compatible with readout function oscilloscopes that automatically detect and display the attenuation factor of the probe.
• Rise Time: The time required for the leading edge of a pulse to rise from 10% to 90% of its final value.
• CMRR: Common Mode Rejection Ratio. A measure of a differential probes ability to reject any signals common to both test points in a differential measurement

Applications

• Use TPI Probes with Bench Top, Portable, Analog, and Oscilloscopes
• Logic signal and waveform tests
• Measure voice / data signals
• Analyze power quality
• Test motor control circuits

Markets

• Electronic
• Communication
• Commercial
• Industrial

GS-AH-A-070-G Gasman Single Gas Monitor, 0-500ppm Carbon Monoxide, Rechargable Battery, German Safe Area only by Crowcon

For over 40 years, Crowcon Detection Instruments has produced state of the art gas detection devices for personal and industrial use. Building upon their reputation for reliable and innovative gas monitoring products, Crowcon introduces the Gasman personal gas monitor. Its lightweight and compact design is convenient for jobsites where workers need not be weighed down by excessive bulk and equipment. The unit conveniently clips to a pocket or helmet and operates continuously.

The Gasman personal gas monitor has numerous convenient features such as:

• One button technology
• Backlit LCD display
• Durable polycarbonate casing
• Quick response triple alert system
• Compact and lightweight design

Easy to Use

The Gasman s true one button technology is an ideal and simple design. The large glove friendly button is mounted on the front of the unit for easy access and controls all of the unit s programmable features. Also on the front, the Gasman s easy to read backlit LCD screen indicates gas readings and the battery status. The simple screen provides a clear indication of the unit s operation status. It will also alert the user 30 days in advance of when a calibration test is due. With a simple and intuitive design, Crowcon has produced a gas detector that reduces the complexities of workplace safety, and ensures workers in a straightforward manner that their equipment is on and operational.

Triple Alarm System

This portable single gas detection system features a triple alarm system that is sure to alert the user and anyone in the vicinity. The visible alarm utilizes a dual red and blue flashing LED light, and the unit houses an internal vibrating alert system. These two indicators allow for visual recognition in loud environments and working conditions. The alarm system also features a programmable audible alarm at 95 decibels. The unit is capable of a variety of alarm tones, and users can select which tone may be best for the individual workplace setting. The triple alarm system with multiple sensory indicators is sure to be noticed in almost any work environment.

Specifications

The Gasman single gas monitor is lightweight and compact, weighing less than 135 grams and with dimensions of 90 x 48 x 24 mm. The unit is available with a wide variety of gas sensors which feature various detection and alarm levels. The unit also features a quick response time of 20 seconds for flammable and toxic gases or 10 seconds for oxygen. Its datalogging feature has approximately 900 hours of storage and all events are time stamped. The battery life for this unit is incredible with 12 hours of runtime on a Rechargeable battery battery or up to 2 years on a non-Rechargeable battery.

6231NKB pH/mV/Temp. Microprocessor Handheld Meter Kit by Jenco

pH/mV/Temp. microprocessor handheld meter in splash proof case with 3 point calibration, BNC, pH/ORP connector with 8-pin DIN ATC connector. AC/DC power. CE Approved

Includes:

• 6231N pH/mV/Temp. Microprocessor Handheld Meter
• 6000P pH/Ref./Temp. Probe
• 6005C Extension Cable

• 3 point calibration
• Power down memories
• Electrode offset recognition
• Electrode slope recognition
• Built in buffer temp. coefficients
• ATC
• CE approved
• Splash resistant/watertight case
• Battery/ac adaptor
• High 50/60hz noise rejection
• UL approved ac line adaptor
• A conventional 9v battery
• Highly reliable mechanical touch keys with audio feedback

Part Number: BWS1-XL-PCB1

Part Number: X105325PM73