$2000 - $4000

*Please note we can only ship RKI products to customers within the United States

2901-21-006 IR 29 e (Increased Safety) Transmitter with Pressure & Humidity Compensation, IP 67, Acetylene (C₂H₂), 0 - 100% LEL Range, No Display / 4-20 mA by GfG

Unlike traditional LEL sensors, IR 29 transmitters do not need the presence of oxygen to detect gas. Since they are not affected by sensor poisons they don't require periodic adjustment to make up for lost sensitivity. The IR 29 continuously monitors its functions for proper performance, and can even identify and communicate required service procedures.

Features

• ATEX: II II 2G Ex eb mb ib [ib] IIC T4 Gb
• Patented infrared technology (NDIR)
• Temperature, moisture and pressure compensation
• Maintenance and service-friendly
• 4-20 mA, linear or digital (Modbus interface)

M-512352 Manning AirScan IRF9 Transmitter, Ammonia (NH3), 0-20,000 ppm, stainless steel enclosure by Honeywell Analytics

The industrial refrigeration industry is changing rapidly. The manufacture of R-22 and other HCFCs are being phased out. Influential organizations such as EPA and CARB (California Air Resources Board) are enforcing lower level monitoring requirements. Manufacturers of cooling systems are introducing new equipment that runs on 407a, 422d, 410a, HFO-1234yf, NH3 and CO2. In step with these changes, EPA fines have escalated for anyone venting ozone-depleting gases. What's your best move? Contact Honeywell Analytics to learn how to detect for these new refrigerants. With Honeywell Analytics, you can green the environment—and green your bottom line.

Honeywell Analytics Infrared monitoring solutions are designed to help your plant operate more efficiently and cost effectively. Unlike sample draw systems which take longer to pinpoint a gas leak, our diffusion sensing technology cuts downtime and the cost of expensive refrigerant replacement. Other technological advantages include flexible standalone or networkable configurations, long operating life expectancy (10+ years); fewer calibration requirements; self-monitoring SensorCheck technology; EPA compliance including newer requirements set by CARB (California Air Resources Board); and accurate, reliable response to the most common refrigerant gases used in industrial or commercial processes.

Refrigerant Specific

• Rapid response to refrigerants including R-404a, R-22, R-507a, R-134a, R-407a, R-410a, R-422d, HFO-1234yf, NH3 and CO2
• Internal monitoring of 4/20 mA loop circuitry continuously
• Compliant with new monitoring standards set by CARB

Diffusion-Design Sensor

• Has no moving parts and doesn't require pumps or filters
• All points of detection can be monitored continuously at an affordable cost

Versatility

• Can be used with any Honeywell Analytics readout
• Standard range of 0-3,000 ppm, can be rescaled for lower trip points
• Provides a linear output of 4/20 mA as a function of refrigerant concentration
• Simple, real-time calibration eliminates maintenance downtime
• Automatically adapts to fluctuating temperatures

Long-Lasting Performance

• Unique internal reference channel compensates for dust particles, source degradation, humidity and temperature fluctuation, food odors, chemical cleaners, etc.

ATMOS™ Technology

• Allows for operation down to -60°F and in condensing humidity environments or during washdown
• Automatically adapts to its environment and provides accurate and reliable performance under the harshest conditions

SensorCheck™ Technology

• Checks operating parameters of sensors and sends a notification output signal if an anomaly is identified
• Tests the sensor every 24 hours for electrical viability
• Indication can be detected by a Manning gas monitor or PLC

Housing

• High-mass metal bench provides structural and thermal stability and greater immunity to vibration
• Superior EMI/RFI shielding

Applications

• Banana and Produce Rooms
• Beverage Plants
• Wineries and Breweries
• Confined Space Entry
• Food Processing
• Gas Bottling Plants
• Ice Rinks
• Product Coolers
• Rack Houses
• Refrigeration Systems
• Supermarkets

2811-709-003 EC 28 Gas Transmitter with Sensor, Chlorine (Cl2), Display / Alarm by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

724-161 Eagle 2 Portable Monitor, LEL(CAT)/CH4(IR %vol)/H2S/CO by RKI Instruments

Continuing in its legacy of durable and reliable gas detection and monitoring systems, RKI Instruments is proud to offer a new product in its popular Eagle portable gas detector series. The Eagle 2 can monitor up to 6 different gases and is equipped with several exclusive features that can only be found with the Eagle series. In addition, its large glove friendly push buttons and LCD screen ensure an ease of use when onsite. Rated intrinsically safe, the Eagle 2 is equipped with state of the art technologies that are not available with other competitive gas detectors and monitors.

Specialty Sensors

The Eagle 2 has a variety of available specialty sensors. Workers can use a photoionization detector for low or high range VOC detection and Fence Electrode Technology for humidity and contamination resistance. An infrared sensor is available for Co2, % LEL CH4, % Volume CH4, % LEL HC, and % Volume HC. Thermal conductivity sensors are available for % Volume H2 and % Volume CH4. The unit is also compatible with the smart plug and play toxic sensors for the detection of NH3, AsH3, CI2, HCN, PH3, and SO2. With the wide variety of sensors and gas detection available, the Eagle 2 can be customized to meet almost all worksite gas detection needs.

Exclusive Features

The monitor has a long internal pump that can draw samples for up to 125 feet. The pump features a low flow auto shut off and alarm. This allows operators to respond swiftly from a safe distance. The unit is multilingual with 5 different language preferences, and features an alkaline battery life of 18 hours or a NiMH life of 20 hours. To protect the integrity of the device and the configurations, the unit can be password protected. The Eagle 2 also has standard data logging capabilities for easy research, evaluation, and site monitoring. To reduce calibration costs and time, the unit features an automatic calibration option and a single gas calibration option.

The Eagle 2 is heavily protected from environmental conditions by a weather proof, chemical resistant RFI/EMI coated high impact polycarbonate/PBT blend enclosure. The enclosure also renders the unit water and dust resistant. Because of the enclosure, the Eagle 2 can function in 2 inches of water without leakage.

Eagle 2 Specifications

The portable and durable unit is lightweight at less than 4 pounds. Its dimensions are suitable for convenient carrying (9.5 L x 5.25 W x 5.875 H), and it features a conveniently placed durable top handle. The large easy to read display has a polyurethane overlay backlights on demand and when the alarm is activated. The 2 alarm channels are fully adjustable for the user and can be password protected. With a 95 dB buzzer and 4 high intensity LEDs, the alarm is sure not to be missed. The Eagle 2 is standard with a 2 year warranty for material and workmanship and a 1 year warranty for PID sensor.

*Please note we can only ship RKI products to customers within the United States

S301-IRF-R514A 301IRF Refrigerant Gas Sensor by Honeywell Analytics

Install Honeywell 301IRF sensor at low levels in chiller room for reliable detection of a variety of refrigerant gasses. Requires installation with a 301EM-20 controller.

Product Overview:

Discreet design and rugged ABS-Polycarbonate housing for the 301IRFS set the standard for "at the source" gas detection in a chiller room. Mount directly to the chiller pad or low on the wall in close proximity to achieve early notifications in the event of a refrigerant leak.

ASHRAE No 15-2001 Mechanical Standard and B-52 Code Compliance. The ASHRAE and B-52 security standards have been established to minimize risk and protect the safety of mechanical room personnel and the environment at large. Honeywell's 301IRF, together with the 301EM mechanical room controller, provides a complete solution that meets and even exceeds these rigorous standards. The 301EM can be configured to offer automatic fan, horn and strobe activation in addition to manual fan activation when the 301IRF detects a refrigerant.

User Friendly:

• State-of-the-art infrared sensor technology
• LED indicator
• Low-profile and rugged construction for low mounting in chiller/mechanical room

Economical Solution:

• Cost-effective answer for installation in areas where refrigeration gas hazards may be present

Detectable Gasses:

• R11, R22, R123, R125, R134A, R404A, R407C, R410A, R448A, R449A, R507A, R513A, R514A, R4310, 1233ZD, 1234ZE.

Features & Benefits:

• Infrared sensing technology responds promptly
• Low-profile design suited for mounting directly to chiller pad or low on nearby wall
• Low maintenance

Quick Specs:

• Power requirement operates on 12 VDC power only
• Dimensions 4" H x 11" W x 2.5" D (10.2 x 28 x 6.3 m)
• Weight 2.33 lbs (0.603 kg)

XNX-AMSV-RNIF1 XNX Universal Transmitter, ATEX M25 SS RLY MPD IR LEL by Honeywell Analytics

XNX Universal Transmitter, ATEX M25 AL FF HRT FOR TOX/O2 SNSRThe XNX Universal Transmitter, now with HART EDDL, marks a new turn in gas detection from Honeywell Analytics. It supports the widest range of sensors on a common platform and offers a modular choice of inputs and outputs.

XNX is designed for flexible integration, simple installation, user-friendly operation and straight-forward maintenance. It is ideal for use with a range of gas monitoring controllers or industry standard PLCs. The introduction of our HART Enhanced Device Descriptor Language (EDDL) software provides users with an at-a-glance indication of the health of their gas detectors in the field.

Bringing together the best solutions in gas detection

Electrochemical

• Proven electrochemical sensing technology
• Surecell™ electrochemical cells are ideal for hot and humid environments
• Long life sensing cells (typical >2 years)
• Patented 'Reflex' sensing element verification diagnostics
• Sensor recognition software auto configures transmitter
• Plug and play factory configured sensors
• Intrinsically safe sensor connection permits hot swap, reducing down time

Catalytic Bead

• Supports Honeywell Analytics 705, 705HT, Sensepoint, Sensepoint HT and MPD sensors
• Fast response to wide range of hydrocarbons and flammables

Infrared (Open Path IR, Point IR, IR Cell)

• Supports Honeywell Analytics Searchline Excel, Searchpoint Optima Plus
• Failsafe operation
• Fast speed of response
• Reduced routine maintenance
• Immune to catalytic poisons
• Long operating life
• Works in inert atmospheres

High performance

• Flammable gas detection 0 to 100% LFL/LEL
• Point IR with heated optics provides immunity to poisoning and no hidden faults
• Open-path IR flammable gas detection in LEL-m measurement
• Electrochemical cell offers toxic gas detection in ppm
• IR cell provides CO₂ and combustible gas monitoring
• Robust and reliable operation in explosive areas and harsh environments

Flexible Operation

• 3 versions - supports (Catalytic Bead and IR Cell), Electrochemical Cell and IR (point and open-path) gas detection
• Multi-Purpose Detector (MPD) with field serviceable mV, Catalytic bead and IR Cell capability
• 4-20mA with HART® as standard
• HART Enhanced Device Description Language (EDDL) software*
• Multiple communications options include up to 3 relays, MODBUS® and FOUNDATION® H1 Fieldbus
• Optional local IS port for handheld HART configurator

Easy to Use

• Large, backlit, easy-to-view LCD display offers multisensory indicators (visual icons, colored buttons, text, etc.) to display gas and sensor readings
• User interface supported by 8 selectable languages (English, Spanish, German, Italian, Portuguese, French, Russian, Chinese)
• Self-test and fault indication features
• Non-intrusive, one-man operation
• Quick calibration with auto-inhibit

Easy to Install

• 3 or 4 wire operation, source, sink or isolated
• Simple plug-in sensors and replaceable cells
• NEMA 4X IP66 rated for rugged indoor/outdoor use
• Five conduit entries for ease of installation

Cost Effective

• Minimal training required
• One-man operation
• Plug-in sensor replacement
• All necessary accessories included

2200-006W GMA 200-MW16 Controller, Configured for 6 Measuring Points, Supply Voltage 24 V/DC, without Power Supply by GfG

The GMA 200-MW is our most flexible and advanced gas detection system controller. The design of the GMA 200-MW ensures simple and clearly structured operation in industrial and commercial applications. The system can be configured for control of any combination of GfG gas transmitters for the measurement of an extremely wide range of toxic and combustible gases and vapors.

Flexible modular design

Each GMA 200-MW module can control up to 16 individual gas transmitters (sensors). The self-contained, IP-65 wall-mounted housing facilitates cost-effective and space-saving installation. GMA 200-MW systems are scalable, and easy to expand by adding additional controller and relay modules. Optional gateway modules allow control via remote or touch-screen computer interface.

Easy to configure

Easy-to-use, menu driven GMA 200-MW software allows configuration of sensor type, gas type, measuring point designations, units of measurement, calibration curves, and function of the comprehensive and fully programmable relays. Up to three individual or specified alarm thresholds can be programmed for each measuring point. The GMA 200-MW continuously evaluates the analog input signals of the connected detectors.

Integrated relays

GMA 200-MW systems include comprehensive and fully programmable relays. Each controller is equipped with 8 internal relays. Menu-driven software allows easy assignment of measuring points to relays, single or multiple alarms per point, alarm thresholds, configuration of collective or group alarms, zoning, fault messages and voting functions.

Relay modules

GMA 200-RW relay modules are housed in easy to install IP-65 wall mounted enclosures. Each relay module provides an additional 16 freely configurable relays. A total of four additional relay modules (for 64 additional relays) can be managed by the same GMA 200-MW system. Digital connection with the GMA 200-MW controller allows remote positioning of the relay module wherever it makes the most sense, substantially reducing cabling and installation costs.

Remote terminal displays

Relay modules are available with or without an integral display for readings and system information, making it easy to add a remote terminal wherever needed.

Optional Fieldbus-Gateways

Optional gateway modules allow integration of the GMA 200-MW system into existing company networks based on TCP/IP, Process Field Bus or Process Field Network protocols. Monitoring and system performance data are easily exported for viewing or analysis. A wifi interface can be added to the gateway to allow wireless connection with a touch screen Windows® computer or smart-phone to display or access system information.

GMA 200 power options

GMA 200-MW power options include traditional voltage inputs (2 x 24 V DC, 20-30 V), as well as operation via a redundant, uninterruptible power supply (UPS), ensuring continued operation of the gas warning system even during a power outage.

Integral alarms

The GMA 200-MW includes built-in bright LED strobe light and loud audible alarms.

LED indicator lights

The status of the GMA 200-MW system (including operation, fault, service, alarm and relay status) is shown via LEDs. Individual LED indicators identify the type and severity of the alarm condition, (FLT, AL1, AL2, AL3), and any relays activated by the condition, (R1 through R8).

Datalogging standard

Measured values, mean values, alarm events and faults are permanently stored on a microSD memory card.

Graphical display

Currently measured values are displayed on a backlit, graphical LCD. In the event of an alarm the display changes color from green to red, and highlights the affected channels.

Five buttons enable operation at the GMA 200-MW controller. The main functions of the keyboard are the acknowledgement of alarms and the menu-driven operation. Information on the status of the controller, detector and the relays can be retrieved in the operating menu.

Operation via keypad

Operation of the GMA 200-MW is through easy-to-use menus, and a simple 5 button interface for alarm acknowledgement, and viewing information on the status of the gas warning system, detectors and relays. The intuitive push-button controls make it easy to navigate through additional screens of information. The integrated display enables the reading of alarm levels through the controller LCD for easy hazard assessment.

Configuration

A built-in USB port in the GMA 200-MW is used for connection to the configuration software. GMA 200-MW systems connected through a Fieldbus gateway can be remotely connected with a GfG factory service center for configuration, diagnostic or service evaluation.

Easy and convenient service

GfG offers full after-the-sale commissioning and field service support.

Additional modules available in IP-65 wall-mounting housings

• External relay module: GMA 200-RW
• Independent power supply: GMA 200-UPS
• Continuous, motorized pump sampling unit: GMA 200-ASV
• Fieldbus gateway: GMA 200-GW

Features

• Advanced and flexible controller for combustible, O₂ and toxic gas
• IP-65 wall-mounting housing, with integral audible and LED alarms
• Flexible, reliable and economic
• Up to 16 transmitters per GMA 200-MW controller in any combination
• Freely programmable relays
• Clearly structured, easy-to-use push-button interface
• Backlit graphic LCD changes color to indicate alarm
• Connect to other measurement devices with 4-20 mA output

72-5398RK Eagle Portable Monitor for HC (% LEL 30% Volume Autoranging)/O2/NH3 by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

Sperian Biosystems PhD6 Multigas Detector

The Biosystems PhD6 Multigas Detector is the latest development in compact multigas detection systems. The detector is proven to be compact, efficient, and cost effective. With dual alarm systems featuring ultra-loud audible indicators and ultra-bright LED visual indicators, users and those nearby are always notified when potential hazards may be present. When developing this detector, the engineers at SperianProtection Instrumentation also developed an express docking station that would reduce calibration time and labor costs. The detection and docking station help users meet record keeping requirements and reduce the risks of human error. With the SperianBiosystems PhD6 Multigas Detector, users can rest assured that they are receiving the very best in gas detection technology.

Key Features

The Biosystems PhD6 Multigas Detector is compatible with over 19 sensor choices including:

• PID
• IR-CO2
• IR-CH4
• Conventional LEL
• Oxygen
• 15 different toxic gas sensors

The gas detector is encased in a durable solid polycarbonate case with a rubber over mold for easy handling. It has an interchangeable battery pack with both Alkaline and Li-Ion rechargeable batteries. Both battery types offer up to 24 hour run times. The unit features dual audible alarms at 92 decibels and front and side ultra-bright LED visual alarms to ensure that the user and those nearby are always notified of possible hazardous conditions. For easy interpretation, the detector has an easy to read status bar and large LCD display that notifies users of the device s functionality and calibration due date. Using the menu options, users can easily adjust a variety of the instrument s settings.

Automatic Docking Station

When developing the PhD6 Multigas Detector, product developers also created an automatic docking station (Biosystems IQ6 Express Dock) to be fully compatible with the detector. The docking station aims to reduce labor time and costs by fully automating certain aspects of instrument maintenance including calibration, functionality testing, and record keeping. Using the Express Dock, users can maintain compliance with recordkeeping requirements by simply docking the detector in the station. The station will automatically perform a variety of operations without user intervention.

Sperian Protection Instrumentation and Honeywell

Sperian Protection Instrumentation is a global leader in personal safety equipment. The company was recently acquired by Honeywell, another global leader in technology and innovation. As a Fortune 100 company, Honeywell has a vested interest in maintaining its reputation as a developer of efficient and reliable safety equipment. Sperian Protection Instrumentation helps to expand Honeywell s personal safety offerings while advancing their position in the American market. By purchasing a product by Sperian and Honeywell, customers can be assured they are receiving the very best in safety technology and equipment.

IT-T4-11Z-ZB-K I-Test Automated Portable Gas Detector Test Station, 1 x Gas Inlet and T4 Module for UL Regional Settings (CH4 set to 2.5%) with C03332 Regulator and AC0510 Cylinder Holder by Crowcon

I-Test is Crowcon's newest solution to test and verify that your Gas-Pro and T4 are in a compliant state to carry out your daily work. Bump testing standards are getting tighter in all regions and the need for controlled bump and calibration records is a must. I-Test and the accompanying I-Test Manager software makes this as easy as can be.

It takes less than 1 minute to complete a bump test with I-Test

Flexible

• Mains powered, or battery back-up - Allows you to use on site, or in field
• Entirely self-contained - No extra computers or equipment required
• Ability to update Gas-Pro and T4 configurations - Update the bump test interval or alarm levels of your fleet with ease and no fleet downtime
• Data management - Archive gas level data from detectors long term
• Powerful support software - Makes configuring I-Test to site requirements extremely easy

Reliable

• I-Test recognises empty or expired cylinders - Allows for planned refills and no unit downtime
• Testing starts automatically when detector is inserted - Minimal user training required
• Ensures the audible and visual alarms are working - Gives the user full confidence that the Gas-Pro is compliant to use
• Battery backup - Testing continues even if power is out

Records

• Everything is logged - See everything that has been tested and whether it has passed/failed
• Exception reporting - Precise reports flag up who has and hasn t carried out their bump test or calibration
• Powerful reporting - Need to see which detectors have gone in to alarm in the last month? I-Test Manager makes easy work of pulling report summaries together

18109329-061 DSX StandAlone Docking Station for MX6, 6 Inlet Ports, North American Power Cord by Industrial Scientific

The DSX™ Docking station is an automated gas detector maintenance, record storage, and fleet management solution that flexes with the needs of your business. Choose from DSX-L Local Server, DSXi Cloud-connected, or DSX Standalone based on your data access requirements. All DSX Docking Stations offer automatic charging, bump testing, and calibration.

• Email alerts and notifications provide information on worker exposure, instrument usage, and instrument service needs
• Print bump test and calibration certificates for hot work and confined space entry
• Auto detect calibration gas type and expiration date upon cylinder connection
• Calibration gas status indicators provide warning to order replacement gas before a cylinder is empty
• DSX Standalone requires no PC or network connection
• DSXi Cloud-connected provides cloud-based record storage with automatic file back-up, fleet management, and automated maintenance and notifications through iNet Control
• DSX-L Local Server provides server-based record storage, fleet management, and automated maintenance and custom data reporting

M5-XU0Y-R-D-D-Y-N-00 GasAlertMicro 5 Detector % LEL (Unfiltered), O2, H2S, CO - Rechargeable Battery - Yellow Housing by BW Technologies

The GasAlertMicro 5 Series is the most customizable gas monitoring series on the market. With an extensive selection of models, user options, and instrument settings, this multi-gas detector series is an industry leader. BW Technologies by Honeywell recognizes that not all worksites can operate with a one size fits all model of gas detection devices. With the introduction of the GasAlertMicro 5 Series multi-gas detectors, worksites, managers, and users can utilize the customizable features to ensure that the instrument meets their specific worksite needs.

GasAlertMicro 5 Series models

This multi-gas monitor series is available in several models: the standard toxic gas model, a PID model for detection of VOCs, or an IR model for CO2 detection. The unit accurately and reliably identifies up to five atmospheric hazards simultaneously and can rapidly switch from diffusion mode to the optional integrated pump.

Each model of GasAlertMicro 5 Series has several distinct features. With the GasAlertMicro 5 Series, the standard toxic gas model, users can monitor several standard gases with a plug in electrochemical cell sensor and catalytic cell sensor and a typical battery life of 20 hours (AA Alkaline rechargeable). The GasAlertMicro 5 PID is standard with several gas detections, a plug in electrochemical cell sensor and photoionization detector, and a battery life of approximately 15 hours (AA Alkaline rechargeable). Finally, the GasAlertMicro 5 IR features specific gas detection ranges, a plug in electrochemical cell sensor, a catalytic cell sensor, and an infrared sensor for carbon dioxide monitoring. This model also has a battery life of approximately 15 and AA Alkaline rechargeable batteries. For more information about available sensor configurations, please contact BW Technologies by Honeywell.

Exclusive features

Each GasAlertMicro 5 Series device features several exclusive features including a triple alarm system, raised glove-friendly buttons, a large easy to read display, stainless steel alligator clip, visual filter inspection, and automatic activation tests. When the unit is activated, the gas detector will automatically test for sensor integrity, circuitry, and battery. This continuous and reliable testing process ensures that the integrity and dependability of the device is never a concern.

BW Technologies by Honeywell also recognizes the unique needs of the various industries with environmental hazards. With each industry anticipating a separate set of possible dangers, the ability to customize safety devices is critical.

Users and worksite managers will be comforted to know their GasAlertMicro 5 series model is fully customizable. Customizable features include STEL intervals, TWA methods, sensor activation, alarms, display settings, record keeping, pumps, combustible gas measurements, start up calibration, backlights, activation modes, calibration levels, daily bump tests, and languages. To protect the integrity of the user settings and the safety of the gas monitoring device, the GasAlertMicro 5 device features a passcode function to prevent unauthorized manipulation of settings.

Accessories

The GasAlertMicro 5 Series is also compatible with BW's MicroDock II automatic test and calibration system. Users may purchase additional accessories to help fully tailor the gas detection unit to their needs. Accessories include an integral pump and battery charger, a confined space kit, a belt holster, and a collapsible sampling probe.

Part Number: M5-XU0Y-R-D-D-Y-N-00

M5-XUAY-R-P-D-Y-N-00 GasAlertMicro 5 Detector % LEL (Unfiltered), O2, H2S, CO, NH3 - Rechargeable Battery and Pump - Yellow Housing by BW Technologies

The GasAlertMicro 5 Series is the most customizable gas monitoring series on the market. With an extensive selection of models, user options, and instrument settings, this multi-gas detector series is an industry leader. BW Technologies by Honeywell recognizes that not all worksites can operate with a one size fits all model of gas detection devices. With the introduction of the GasAlertMicro 5 Series multi-gas detectors, worksites, managers, and users can utilize the customizable features to ensure that the instrument meets their specific worksite needs.

GasAlertMicro 5 Series models

This multi-gas monitor series is available in several models: the standard toxic gas model, a PID model for detection of VOCs, or an IR model for CO2 detection. The unit accurately and reliably identifies up to five atmospheric hazards simultaneously and can rapidly switch from diffusion mode to the optional integrated pump.

Each model of GasAlertMicro 5 Series has several distinct features. With the GasAlertMicro 5 Series, the standard toxic gas model, users can monitor several standard gases with a plug in electrochemical cell sensor and catalytic cell sensor and a typical battery life of 20 hours (AA Alkaline rechargeable). The GasAlertMicro 5 PID is standard with several gas detections, a plug in electrochemical cell sensor and photoionization detector, and a battery life of approximately 15 hours (AA Alkaline rechargeable). Finally, the GasAlertMicro 5 IR features specific gas detection ranges, a plug in electrochemical cell sensor, a catalytic cell sensor, and an infrared sensor for carbon dioxide monitoring. This model also has a battery life of approximately 15 and AA Alkaline rechargeable batteries. For more information about available sensor configurations, please contact BW Technologies by Honeywell.

Exclusive features

Each GasAlertMicro 5 Series device features several exclusive features including a triple alarm system, raised glove-friendly buttons, a large easy to read display, stainless steel alligator clip, visual filter inspection, and automatic activation tests. When the unit is activated, the gas detector will automatically test for sensor integrity, circuitry, and battery. This continuous and reliable testing process ensures that the integrity and dependability of the device is never a concern.

BW Technologies by Honeywell also recognizes the unique needs of the various industries with environmental hazards. With each industry anticipating a separate set of possible dangers, the ability to customize safety devices is critical.

Users and worksite managers will be comforted to know their GasAlertMicro 5 series model is fully customizable. Customizable features include STEL intervals, TWA methods, sensor activation, alarms, display settings, record keeping, pumps, combustible gas measurements, start up calibration, backlights, activation modes, calibration levels, daily bump tests, and languages. To protect the integrity of the user settings and the safety of the gas monitoring device, the GasAlertMicro 5 device features a passcode function to prevent unauthorized manipulation of settings.

Accessories

The GasAlertMicro 5 Series is also compatible with BW's MicroDock II automatic test and calibration system. Users may purchase additional accessories to help fully tailor the gas detection unit to their needs. Accessories include an integral pump and battery charger, a confined space kit, a belt holster, and a collapsible sampling probe.

Part Number: M5-XUAY-R-P-D-Y-N-00

VTS-L000211051C Ventis MX4 Multi-Gas Monitor, LEL (Methane), Li-ion Extended Run Time Battery, Desktop Charger, Pump, Black, China EX, Soft Case, Chinese by Industrial Scientific

The Ventis® MX4 is a four-gas monitor with the portability and size of a single-gas monitor. Eliminate the need for extra monitors and transition seamlessly from personal monitoring to confined space entry with the Ventis® Slide-on Pump— ideal for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries.

• Detect up to four gases with a wide range of sensor options
• Select alarm set points, set latch alarms, disable instrument shutdown while in alarm, and more
• Save time and reduce human error with maintenance and usage data available from iNet Control software
• Available with or without an integral pump, or with the Ventis Slide-on Pump for ultimate flexibility
• Non-pumped instruments compatible with 12-hour, 18-hour, or 20-hour batteries

The Ventis® Slide-on Pump

The Ventis® Slide-on Pump is ideally suited for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries. Available in black or safety orange and powered by its own battery, the slide-on pump is compatible with the Ventis MX4 and Ventis® Pro5 Multi-Gas Monitor.

• Convenient Sampling – Sample draw distance of up to 50 feet provides convenient sampling in a wide range of applications
• Easy to Attach – No tools are required to attach or remove the Ventis Slide-on Pump to or from the monitor
• Uses Same Batterys and Chargers as Ventis – Monitor and pump each use the same batterys, and can easily be exchanged between instruments
• Flexible Battery Options – Three available battery options make this pump extremely flexible in the field

10184924 Altair 4XR Multigas Detector by MSA

Outfitted with rapid-response MSA XCell® sensors, the ALTAIR 4XR Gas Detector is the toughest 4-gas monitor on the market and is backed by a 4-year warranty. The ALTAIR 4XR can also provide real-time incident awareness to team members, supervisors, safety managers and others when paired with the MSA ALTAIR Connect app via a Bluetooth® wireless connection.

Real-time

• Sense gas 2 times faster than the industry average with our XCell sensors
• Quickly update MSA ALTAIR 4XR settings via the ALTAIR Connect app (available on the Google Play Store)
• Send event notifications via text message with the ALTAIR Connect app

Rugged

• Survives 25 drops from 4 feet (1.2 meters) (MIL-STD-810G drop protection)
• Can survive an incidental 25-foot (7.5-m) drop onto concrete
• Dust- and waterproof IP68 rating (2 meters for at least 1 hour)
• Operating temperature range: -40°F to +140°F (-40°C to +60°C)

Reliable

• 4-year instrument & sensor warranty
• Confirm compliance quickly with the Bump LED & on-screen checkmark
• Bump and calibrate with 1/2 the test gas and in 1/2 the time vs. industry average
• Bump and calibrate at a specified "Time of Day" with your MSA GALAXY® GX2 Automated Test System
• MotionAlert option tells others that user has become immobile
• User-activated InstantAlert notifies others of a potentially dangerous situation

72-5241RKS Eagle Portable Monitor for HCI/AsH3 0-0.200 PPM (with HCI Scrubber) by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

72-5246RK Eagle Portable Monitor for LEL & PPM/F2, (No Probe) by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

500-5 Handheld Combustion Efficiency Emissions Analyzer includes O2, CO, NO (Nitric Oxide), Temperature, Draft, Printer by Enerac

Enerac invented the first electronic portable multi-parameter combustion analyzer in 1979 (in the USA). Enerac still services this analyzer as well as all others Enerac has manufactured. The Enerac Model 500 is a low-cost, easy to use (no technical expertise needed) portable combustion efficiency emissions analyzer. The Enerac 500 is perfect for determining the efficiency of a combustion source as well as for collecting advanced emissions data for internal use, or for local, state and federal emissions reporting requirements.

The Enerac 500 is perfect for testing various combustion sources, such as boilers, burners, engines, turbines, generators, kilns, dryers, heaters and ovens (just to name a few). Equally, with a simple combustion efficiency test, or a more advanced combustion emissions test, the Enerac 500 is designed to provide years of trouble-free service. It is flexible enough to be tailored to meet your specific needs, yet simple enough to be completely maintained in the field. Advanced design, rugged construction and an impressive array of options are its hallmark. Constructed as a field work-horse the Enerac 500 can be upgraded (adding sensors and options to the same unit) to meet your changing needs at any time.

Introduction

The Enerac 500 provides a comprehensive range of automatic emissions calculations, advanced Enercom Windows Software, two-way communications and factory support. From low NOx burners, (0.1ppm NOxresolution) to large rich burn engines (5,000ppm (NOx)/20,000ppm CO) the Enerac 500 is designed to help meet your needs of various monitoring applications at an affordable price.

The Enerac 500 handheld combustion efficiency emissions analyzer, is our newest, low cost, Emissions-Monitoring System, utilizing standard electrochemical sensors. It is designed to help you meet the challenges of a rapidly changing regulatory environment. It is easy to use, comprehensive (O2-CO-NO-NO2-(NOx), SO2, Combustibles, Stack Temperature, Draft), and flexible.

• A micro-sized Combustion-Efficiency analyzer and Emissions-Monitoring System
• Thermoelectric Condenser / Peltier Cooler (sample conditioning system for proper detection and measurement of NO2 and/or SO2 gasses
• Powered by 4xAA Rechargeable batteries
• Built-in Thermal Printer: 2" Character-type
• Our Enercom Windows Software included
• USB and Serial Ports included. Bluetooth Wireless (optional)

Rugged

The Enerac 500 is designed for years of trouble-free service. Housed in a rugged, lightweight aluminum case, its modular design allows end-users the ability to replace a battery or sensor, in a matter of seconds. Reducing both downtime and costs.

• Rugged lightweight aluminum case
• Work-horse of the industry
• Won't warp or crack like plastic models
• Small, lightweight and tough
• 2 Year Warranty
• 24 Hour Service
• Best service and support in the industry

Comprehensive

The Enerac 500 provides an extensive range of data management, and support options. It not only (automatically) performs complicated emission calculations, it can even allow the user the ability to identify specific data sets with a specific customer, dramatically reducing retrieval and processing costs.

Enerac 500 is compatible with Enerac's advanced Enercom for Windows ™ software. All parameters can be continuously displayed; Minimum, Maximum, Averages and Standard Deviations calculated; Multiple plots and graphs can be viewed or printed. With the Enercom software, data management and report writing is now a snap. With the Enerac 500, help is never more than a phone call or email away.

Affordable

With all these capabilities the Enerac 500 is surprisingly affordable.

• Buy only what you need and add options later
• Always upgradeable (anytime)!
• Free software and accessories
• Receive a generous trade-in allowance on your old analyzer
• Loaners available at no charge.

Compliance Level

The Enerac 500 can be configured to a compliance-level analyzer with addition of several key features. The Enerac 500 has the ability to produce Total NOx data for one. With both the NO and NO2 sensors Total NOxis obtained (NOx)=NO+NO2 on stationary combustion sources). The ability to also configure the 500 with High Sensativity sensors allows extreme accuracy over the sensors shorter range etc. Additionally, the 500 has the option to have the Thermoelectric Condenser (also called Peltier Cooler) option installed. This is a sample conditioning system (usually found on our competitors larger more expensive units) essential for proper NO2 and or SO2 gas detection and measurement. With the final addition of the viton hose, sample quality is maintained and compliance level data obtained. Therefore, the Enerac 500 is perfect for meeting your local, state and federal regulatory emissions compliance requirements.

• Free data collection software
• Time-stamped internal data storage
• Total NOx (NO and NO2)
• High Sensitivity / Low Range Sensors Available
• Viton and Teflon hose options
• Sample Conditioning System (for proper NO2 and/or SO2 gas detection and measurement)
• Field replaceable sensors
• Easy field calibrations (if desired)
• Comply with local, state and federal emissions requirements

In a world of downsizing, and increasing workloads, the Enerac 500 can help you simplify your job. With a broad array of available options, the Enerac 500 will provide you with the capabilities you need, when you need them, all within your budget.

Sperian Biosystems PhD6 Multigas Detector

The Biosystems PhD6 Multigas Detector is the latest development in compact multigas detection systems. The detector is proven to be compact, efficient, and cost effective. With dual alarm systems featuring ultra-loud audible indicators and ultra-bright LED visual indicators, users and those nearby are always notified when potential hazards may be present. When developing this detector, the engineers at SperianProtection Instrumentation also developed an express docking station that would reduce calibration time and labor costs. The detection and docking station help users meet record keeping requirements and reduce the risks of human error. With the SperianBiosystems PhD6 Multigas Detector, users can rest assured that they are receiving the very best in gas detection technology.

Key Features

The Biosystems PhD6 Multigas Detector is compatible with over 19 sensor choices including:

• PID
• IR-CO2
• IR-CH4
• Conventional LEL
• Oxygen
• 15 different toxic gas sensors

The gas detector is encased in a durable solid polycarbonate case with a rubber over mold for easy handling. It has an interchangeable battery pack with both Alkaline and Li-Ion rechargeable batteries. Both battery types offer up to 24 hour run times. The unit features dual audible alarms at 92 decibels and front and side ultra-bright LED visual alarms to ensure that the user and those nearby are always notified of possible hazardous conditions. For easy interpretation, the detector has an easy to read status bar and large LCD display that notifies users of the device s functionality and calibration due date. Using the menu options, users can easily adjust a variety of the instrument s settings.

Automatic Docking Station

When developing the PhD6 Multigas Detector, product developers also created an automatic docking station (Biosystems IQ6 Express Dock) to be fully compatible with the detector. The docking station aims to reduce labor time and costs by fully automating certain aspects of instrument maintenance including calibration, functionality testing, and record keeping. Using the Express Dock, users can maintain compliance with recordkeeping requirements by simply docking the detector in the station. The station will automatically perform a variety of operations without user intervention.

Sperian Protection Instrumentation and Honeywell

Sperian Protection Instrumentation is a global leader in personal safety equipment. The company was recently acquired by Honeywell, another global leader in technology and innovation. As a Fortune 100 company, Honeywell has a vested interest in maintaining its reputation as a developer of efficient and reliable safety equipment. Sperian Protection Instrumentation helps to expand Honeywell s personal safety offerings while advancing their position in the American market. By purchasing a product by Sperian and Honeywell, customers can be assured they are receiving the very best in safety technology and equipment.

Sperian Biosystems PhD6 Multigas Detector

The Biosystems PhD6 Multigas Detector is the latest development in compact multigas detection systems. The detector is proven to be compact, efficient, and cost effective. With dual alarm systems featuring ultra-loud audible indicators and ultra-bright LED visual indicators, users and those nearby are always notified when potential hazards may be present. When developing this detector, the engineers at SperianProtection Instrumentation also developed an express docking station that would reduce calibration time and labor costs. The detection and docking station help users meet record keeping requirements and reduce the risks of human error. With the SperianBiosystems PhD6 Multigas Detector, users can rest assured that they are receiving the very best in gas detection technology.

Key Features

The Biosystems PhD6 Multigas Detector is compatible with over 19 sensor choices including:

• PID
• IR-CO2
• IR-CH4
• Conventional LEL
• Oxygen
• 15 different toxic gas sensors

The gas detector is encased in a durable solid polycarbonate case with a rubber over mold for easy handling. It has an interchangeable battery pack with both Alkaline and Li-Ion rechargeable batteries. Both battery types offer up to 24 hour run times. The unit features dual audible alarms at 92 decibels and front and side ultra-bright LED visual alarms to ensure that the user and those nearby are always notified of possible hazardous conditions. For easy interpretation, the detector has an easy to read status bar and large LCD display that notifies users of the device s functionality and calibration due date. Using the menu options, users can easily adjust a variety of the instrument s settings.

Automatic Docking Station

When developing the PhD6 Multigas Detector, product developers also created an automatic docking station (Biosystems IQ6 Express Dock) to be fully compatible with the detector. The docking station aims to reduce labor time and costs by fully automating certain aspects of instrument maintenance including calibration, functionality testing, and record keeping. Using the Express Dock, users can maintain compliance with recordkeeping requirements by simply docking the detector in the station. The station will automatically perform a variety of operations without user intervention.

Sperian Protection Instrumentation and Honeywell

Sperian Protection Instrumentation is a global leader in personal safety equipment. The company was recently acquired by Honeywell, another global leader in technology and innovation. As a Fortune 100 company, Honeywell has a vested interest in maintaining its reputation as a developer of efficient and reliable safety equipment. Sperian Protection Instrumentation helps to expand Honeywell s personal safety offerings while advancing their position in the American market. By purchasing a product by Sperian and Honeywell, customers can be assured they are receiving the very best in safety technology and equipment.

Sperian Biosystems PhD6 Multigas Detector

The Biosystems PhD6 Multigas Detector is the latest development in compact multigas detection systems. The detector is proven to be compact, efficient, and cost effective. With dual alarm systems featuring ultra-loud audible indicators and ultra-bright LED visual indicators, users and those nearby are always notified when potential hazards may be present. When developing this detector, the engineers at SperianProtection Instrumentation also developed an express docking station that would reduce calibration time and labor costs. The detection and docking station help users meet record keeping requirements and reduce the risks of human error. With the SperianBiosystems PhD6 Multigas Detector, users can rest assured that they are receiving the very best in gas detection technology.

Key Features

The Biosystems PhD6 Multigas Detector is compatible with over 19 sensor choices including:

• PID
• IR-CO2
• IR-CH4
• Conventional LEL
• Oxygen
• 15 different toxic gas sensors

The gas detector is encased in a durable solid polycarbonate case with a rubber over mold for easy handling. It has an interchangeable battery pack with both Alkaline and Li-Ion rechargeable batteries. Both battery types offer up to 24 hour run times. The unit features dual audible alarms at 92 decibels and front and side ultra-bright LED visual alarms to ensure that the user and those nearby are always notified of possible hazardous conditions. For easy interpretation, the detector has an easy to read status bar and large LCD display that notifies users of the device s functionality and calibration due date. Using the menu options, users can easily adjust a variety of the instrument s settings.

Automatic Docking Station

When developing the PhD6 Multigas Detector, product developers also created an automatic docking station (Biosystems IQ6 Express Dock) to be fully compatible with the detector. The docking station aims to reduce labor time and costs by fully automating certain aspects of instrument maintenance including calibration, functionality testing, and record keeping. Using the Express Dock, users can maintain compliance with recordkeeping requirements by simply docking the detector in the station. The station will automatically perform a variety of operations without user intervention.

Sperian Protection Instrumentation and Honeywell

Sperian Protection Instrumentation is a global leader in personal safety equipment. The company was recently acquired by Honeywell, another global leader in technology and innovation. As a Fortune 100 company, Honeywell has a vested interest in maintaining its reputation as a developer of efficient and reliable safety equipment. Sperian Protection Instrumentation helps to expand Honeywell s personal safety offerings while advancing their position in the American market. By purchasing a product by Sperian and Honeywell, customers can be assured they are receiving the very best in safety technology and equipment.