$2000 - $4000

READY-8 Dewatering Pump, 1.1 HP, 120V AC, 9.8 Amp, 2" Discharge, 90 GPM, Submersible by Pelsue

ALL Submersible pumps come ready to use, equipped with coupler, rope, & power-cord. See below for details.

RT07 Rescue Tripod, Max. Height 7' with Built in Cable Pulley by Pelsue

The Pelsue Rescue Tripod is designed for industrial rescue applications. Telescoping anodized-aluminum legs allow for height adjustments in 5" increments per leg. The legs also adjust to any angle to meet the most demanding situations! Cast-aluminum head has three heavy duty rigging anchor points plus built-in, man rated, cable ready pulley. Our rescue tripod adjusts to 11'-6" allowing for full retrieval of a litter basket in vertical rescues. Tripod also features locking legs.

Features:

• Minimum height: 6' Model P054, 4' Model RT07
• Maximum height: 11'6" Model P054, 7' Model RT07
• Weight: 62 lbs. Model P054, 57 lbs Model RT07
• Three rigging anchor points proof rated to 5000 lbs. at fully extended height
• Built-in cable ready pulley
• No load supporting welds
• Adjustable telescoping legs - 5" increments
• Feet convert to soft ground anchors and are predrilled for anchor bolts or stakes
• Base chain included to maintain stability

WH07C Equipment Hoist - Max Load 700lbs with 3/16" X 70' SS Cable by Pelsue

The Pelsue WH Series Work Hoist is designed to be an equipment hoisting and lowering device. This specification sheet applies to the Model #WH07C and the Model #WH07R. Below is a table of the available Pelsue Work Hoist Models and information on their included cable/rope size. The standard end fitting included on all rope or cable assemblies is a swiveling double-locking snap hook, but alternate end fittings are available upon request. The WH Series Work Hoist is equipped with a standard Pelsue Quick-Release bracket (#501073-001). Other adapter brackets can be supplied or added upon request. The WH Series Work Hoists are for the lifting of equipment only, at no time should personnel be attached to the hoist cable/rope! The WH Series Work Hoist is not to be used for lifting loads over areas where people are present!

Load Capacity:

Pelsue WH Series Work Hoists are designed and tested as Mechanical Lifting Device for equipment Only.

Load Capacity........................... 700 LBS. (317 KG)
Gear Ratio................................. 5 to 1

Rope & Cable Assemblies:

3/16" Stainless Steel Wire Rope:
Minimum Breaking Strength........................ 3500 LBS. (1587 KG)

3/16" "Technora" Synthetic Rope:
Minimum Breaking Strength........................ 5500 LBS. (2494 KG)

Weight:

WH07C (Steel Cable)..........25 LBS. (11.3 KG)
WH07R (Synthetic Rope)....21 LBS. (9.5 KG)

WH07R Equipment Hoist - Max Load 700lbs with 3/16" X 70' Synthetic Rope by Pelsue

The Pelsue WH Series Work Hoist is designed to be an equipment hoisting and lowering device. This specification sheet applies to the Model #WH07C and the Model #WH07R. Below is a table of the available Pelsue Work Hoist Models and information on their included cable/rope size. The standard end fitting included on all rope or cable assemblies is a swiveling double-locking snap hook, but alternate end fittings are available upon request. The WH Series Work Hoist is equipped with a standard Pelsue Quick-Release bracket (#501073-001). Other adapter brackets can be supplied or added upon request. The WH Series Work Hoists are for the lifting of equipment only, at no time should personnel be attached to the hoist cable/rope! The WH Series Work Hoist is not to be used for lifting loads over areas where people are present!

Load Capacity:

Pelsue WH Series Work Hoists are designed and tested as Mechanical Lifting Device for equipment Only.

Load Capacity........................... 700 LBS. (317 KG)
Gear Ratio................................. 5 to 1

Rope & Cable Assemblies:

3/16" Stainless Steel Wire Rope:
Minimum Breaking Strength........................ 3500 LBS. (1587 KG)

3/16" "Technora" Synthetic Rope:
Minimum Breaking Strength........................ 5500 LBS. (2494 KG)

Weight:

WH07C (Steel Cable)..........25 LBS. (11.3 KG)
WH07R (Synthetic Rope)....21 LBS. (9.5 KG)

S301-IRF-1234ZE 301IRF Refrigerant Gas Sensor by Honeywell Analytics

Install Honeywell 301IRF sensor at low levels in chiller room for reliable detection of a variety of refrigerant gasses. Requires installation with a 301EM-20 controller.

Product Overview:

Discreet design and rugged ABS-Polycarbonate housing for the 301IRFS set the standard for "at the source" gas detection in a chiller room. Mount directly to the chiller pad or low on the wall in close proximity to achieve early notifications in the event of a refrigerant leak.

ASHRAE No 15-2001 Mechanical Standard and B-52 Code Compliance. The ASHRAE and B-52 security standards have been established to minimize risk and protect the safety of mechanical room personnel and the environment at large. Honeywell's 301IRF, together with the 301EM mechanical room controller, provides a complete solution that meets and even exceeds these rigorous standards. The 301EM can be configured to offer automatic fan, horn and strobe activation in addition to manual fan activation when the 301IRF detects a refrigerant.

User Friendly:

• State-of-the-art infrared sensor technology
• LED indicator
• Low-profile and rugged construction for low mounting in chiller/mechanical room

Economical Solution:

• Cost-effective answer for installation in areas where refrigeration gas hazards may be present

Detectable Gasses:

• R11, R22, R123, R125, R134A, R404A, R407C, R410A, R448A, R449A, R507A, R513A, R514A, R4310, 1233ZD, 1234ZE.

Features & Benefits:

• Infrared sensing technology responds promptly
• Low-profile design suited for mounting directly to chiller pad or low on nearby wall
• Low maintenance

Quick Specs:

• Power requirement operates on 12 VDC power only
• Dimensions 4" H x 11" W x 2.5" D (10.2 x 28 x 6.3 m)
• Weight 2.33 lbs (0.603 kg)

S301-IRF-R125 301IRF Refrigerant Gas Sensor by Honeywell Analytics

Install Honeywell 301IRF sensor at low levels in chiller room for reliable detection of a variety of refrigerant gasses. Requires installation with a 301EM-20 controller.

Product Overview:

Discreet design and rugged ABS-Polycarbonate housing for the 301IRFS set the standard for "at the source" gas detection in a chiller room. Mount directly to the chiller pad or low on the wall in close proximity to achieve early notifications in the event of a refrigerant leak.

ASHRAE No 15-2001 Mechanical Standard and B-52 Code Compliance. The ASHRAE and B-52 security standards have been established to minimize risk and protect the safety of mechanical room personnel and the environment at large. Honeywell's 301IRF, together with the 301EM mechanical room controller, provides a complete solution that meets and even exceeds these rigorous standards. The 301EM can be configured to offer automatic fan, horn and strobe activation in addition to manual fan activation when the 301IRF detects a refrigerant.

User Friendly:

• State-of-the-art infrared sensor technology
• LED indicator
• Low-profile and rugged construction for low mounting in chiller/mechanical room

Economical Solution:

• Cost-effective answer for installation in areas where refrigeration gas hazards may be present

Detectable Gasses:

• R11, R22, R123, R125, R134A, R404A, R407C, R410A, R448A, R449A, R507A, R513A, R514A, R4310, 1233ZD, 1234ZE.

Features & Benefits:

• Infrared sensing technology responds promptly
• Low-profile design suited for mounting directly to chiller pad or low on nearby wall
• Low maintenance

Quick Specs:

• Power requirement operates on 12 VDC power only
• Dimensions 4" H x 11" W x 2.5" D (10.2 x 28 x 6.3 m)
• Weight 2.33 lbs (0.603 kg)

S301-IRF-R22 301IRF Refrigerant Gas Sensor by Honeywell Analytics

Install Honeywell 301IRF sensor at low levels in chiller room for reliable detection of a variety of refrigerant gasses. Requires installation with a 301EM-20 controller.

Product Overview:

Discreet design and rugged ABS-Polycarbonate housing for the 301IRFS set the standard for "at the source" gas detection in a chiller room. Mount directly to the chiller pad or low on the wall in close proximity to achieve early notifications in the event of a refrigerant leak.

ASHRAE No 15-2001 Mechanical Standard and B-52 Code Compliance. The ASHRAE and B-52 security standards have been established to minimize risk and protect the safety of mechanical room personnel and the environment at large. Honeywell's 301IRF, together with the 301EM mechanical room controller, provides a complete solution that meets and even exceeds these rigorous standards. The 301EM can be configured to offer automatic fan, horn and strobe activation in addition to manual fan activation when the 301IRF detects a refrigerant.

User Friendly:

• State-of-the-art infrared sensor technology
• LED indicator
• Low-profile and rugged construction for low mounting in chiller/mechanical room

Economical Solution:

• Cost-effective answer for installation in areas where refrigeration gas hazards may be present

Detectable Gasses:

• R11, R22, R123, R125, R134A, R404A, R407C, R410A, R448A, R449A, R507A, R513A, R514A, R4310, 1233ZD, 1234ZE.

Features & Benefits:

• Infrared sensing technology responds promptly
• Low-profile design suited for mounting directly to chiller pad or low on nearby wall
• Low maintenance

Quick Specs:

• Power requirement operates on 12 VDC power only
• Dimensions 4" H x 11" W x 2.5" D (10.2 x 28 x 6.3 m)
• Weight 2.33 lbs (0.603 kg)