$2000 - $4000

FS7-2173 FS7 Multi-Spectrum Fire and Flame Detector, Viton O-ring for use with FS7-130-SX Controller, FSWB Control Panel or S7-2175 Control Panel by Honeywell Analytics

The Fire Sentry FS7-2173 electro-optical radiant energy fire detector - and the Fire Sentry FS7-2173-2RP (unitized model) with multi-spectral WideBand IR™, Near Band IR and Visible Band fire detection are designed specifically for semiconductor Clean Room fire protection applications.

The Fire Sentry FS7 fire detector provides and intelligent two-stage response to semiconductor wet bench fires:

Stage 1: Alert. This is the first-stage response to a small fire with a heat energy output of 3 kW (the equivalent of a 4-inch diameter polypropylene pool fire). This allows time for the fire to self-extinguish.

Stage 2: Alarm. If the fire does not self-extinguish, and grows to the Factory Mutual specified heat energy threshold of 13 kW (the equivalent of an 8-inch diameter polypropylene pool fire), the second-stage response is activated.

The Fire Sentry FS7-2173 is used with Fire Sentry FS7-130-SX Controller or Control Panel FSWB. Controller and Control Panel supply power to detectors monitor the status of all detectors and communicate with the detectors via the digital RS-485 communication channel. Fire Sentry FS7-2173 is supplied with a standard 20 ft. cable connector. Detectors are connected to the controller or control panel using the self-locking connectors and Fire Sentry junction boxes. This allows for fast and easy connections eliminating wiring problems. Each detector can store up to six time and date stamped FirePics™ (pre-event multi-spectral sensor array data) in non-volatile memory. Controller and control panel can also store event history table in the non-volatile memory, which contains the time and date stamped alert, alarm and fault histories. FirePics™ and event histories can be retrieved from the controller or control panel.

Fire Sentry FS7-2173-2RP unitized model's microprocessor, with digital signal processing algorithms, continuously monitors the circuitry, sensor's built-in selftest and verifies proper operation. Fire Sentry FS7-2173-2RP with discrete relay outputs is designed to operate as a stand-alone detector and interface with any approved fire alarm panel. The detector requires an external 24 VDC power source and is supplied with a standard 20 ft. pigtail cable. It can store up to six time and date stamped FirePics™ and 200 events in non-volatile memory. FirePics™ and event histories can be retrieved using a Fire Sentry FS7 Interface Kit and the Fire Sentry Windows-based PC software.

Features:

• Multi-Spectral digital electro-optical radiant energy infrared fire detector
• Unique two-stage fire detection response
• Immune to false alarm sources
• NOT affected by absorbing smoke, gasses or chemical vapors
• NOT sensitive to background radiant energy from electric heaters and ovens
• Detects hydrocarbon and non-hydrocarbon fires
• Rugged leak-proof, heat-sealed, acid-resistant, injection-molded polypropylene housing
• Wide 120° field-of-view
• Digital communication with RS-485 interface
• FirePic™; time and date-stamped digital fire signatures
• Built-in detector automatic self test
• Unitzed model design for stand-alone operation

Applications include:

• Open Areas of Clean Room
• Wet Bench Working Surface
• Wet Bench Subsurface (Plenum)
• Pumps and Equipment Located Behind the Wet Bench Area
• Under-floor Areas
• IPA Stations (Unitized model only)

FS7-2173-2RP-K FS7 Multi-Spectrum Fire and Flame Detector, Non-Latching Alert and Alarm Relays, Kal-rez O-ring by Honeywell Analytics

The Fire Sentry FS7-2173 electro-optical radiant energy fire detector - and the Fire Sentry FS7-2173-2RP (unitized model) with multi-spectral WideBand IR™, Near Band IR and Visible Band fire detection are designed specifically for semiconductor Clean Room fire protection applications.

The Fire Sentry FS7 fire detector provides and intelligent two-stage response to semiconductor wet bench fires:

Stage 1: Alert. This is the first-stage response to a small fire with a heat energy output of 3 kW (the equivalent of a 4-inch diameter polypropylene pool fire). This allows time for the fire to self-extinguish.

Stage 2: Alarm. If the fire does not self-extinguish, and grows to the Factory Mutual specified heat energy threshold of 13 kW (the equivalent of an 8-inch diameter polypropylene pool fire), the second-stage response is activated.

The Fire Sentry FS7-2173 is used with Fire Sentry FS7-130-SX Controller or Control Panel FSWB. Controller and Control Panel supply power to detectors monitor the status of all detectors and communicate with the detectors via the digital RS-485 communication channel. Fire Sentry FS7-2173 is supplied with a standard 20 ft. cable connector. Detectors are connected to the controller or control panel using the self-locking connectors and Fire Sentry junction boxes. This allows for fast and easy connections eliminating wiring problems. Each detector can store up to six time and date stamped FirePics™ (pre-event multi-spectral sensor array data) in non-volatile memory. Controller and control panel can also store event history table in the non-volatile memory, which contains the time and date stamped alert, alarm and fault histories. FirePics™ and event histories can be retrieved from the controller or control panel.

Fire Sentry FS7-2173-2RP unitized model's microprocessor, with digital signal processing algorithms, continuously monitors the circuitry, sensor's built-in selftest and verifies proper operation. Fire Sentry FS7-2173-2RP with discrete relay outputs is designed to operate as a stand-alone detector and interface with any approved fire alarm panel. The detector requires an external 24 VDC power source and is supplied with a standard 20 ft. pigtail cable. It can store up to six time and date stamped FirePics™ and 200 events in non-volatile memory. FirePics™ and event histories can be retrieved using a Fire Sentry FS7 Interface Kit and the Fire Sentry Windows-based PC software.

Features:

• Multi-Spectral digital electro-optical radiant energy infrared fire detector
• Unique two-stage fire detection response
• Immune to false alarm sources
• NOT affected by absorbing smoke, gasses or chemical vapors
• NOT sensitive to background radiant energy from electric heaters and ovens
• Detects hydrocarbon and non-hydrocarbon fires
• Rugged leak-proof, heat-sealed, acid-resistant, injection-molded polypropylene housing
• Wide 120° field-of-view
• Digital communication with RS-485 interface
• FirePic™; time and date-stamped digital fire signatures
• Built-in detector automatic self test
• Unitzed model design for stand-alone operation

Applications include:

• Open Areas of Clean Room
• Wet Bench Working Surface
• Wet Bench Subsurface (Plenum)
• Pumps and Equipment Located Behind the Wet Bench Area
• Under-floor Areas
• IPA Stations (Unitized model only)

FS7-2173-2RPC-K FS7 Multi-Spectrum Fire and Flame Detector, LOW SENS 20C 41T KALREZ (KFPI) by Honeywell Analytics

The Fire Sentry FS7-2173 electro-optical radiant energy fire detector - and the Fire Sentry FS7-2173-2RP (unitized model) with multi-spectral WideBand IR™, Near Band IR and Visible Band fire detection are designed specifically for semiconductor Clean Room fire protection applications.

The Fire Sentry FS7 fire detector provides and intelligent two-stage response to semiconductor wet bench fires:

Stage 1: Alert. This is the first-stage response to a small fire with a heat energy output of 3 kW (the equivalent of a 4-inch diameter polypropylene pool fire). This allows time for the fire to self-extinguish.

Stage 2: Alarm. If the fire does not self-extinguish, and grows to the Factory Mutual specified heat energy threshold of 13 kW (the equivalent of an 8-inch diameter polypropylene pool fire), the second-stage response is activated.

The Fire Sentry FS7-2173 is used with Fire Sentry FS7-130-SX Controller or Control Panel FSWB. Controller and Control Panel supply power to detectors monitor the status of all detectors and communicate with the detectors via the digital RS-485 communication channel. Fire Sentry FS7-2173 is supplied with a standard 20 ft. cable connector. Detectors are connected to the controller or control panel using the self-locking connectors and Fire Sentry junction boxes. This allows for fast and easy connections eliminating wiring problems. Each detector can store up to six time and date stamped FirePics™ (pre-event multi-spectral sensor array data) in non-volatile memory. Controller and control panel can also store event history table in the non-volatile memory, which contains the time and date stamped alert, alarm and fault histories. FirePics™ and event histories can be retrieved from the controller or control panel.

Fire Sentry FS7-2173-2RP unitized model's microprocessor, with digital signal processing algorithms, continuously monitors the circuitry, sensor's built-in selftest and verifies proper operation. Fire Sentry FS7-2173-2RP with discrete relay outputs is designed to operate as a stand-alone detector and interface with any approved fire alarm panel. The detector requires an external 24 VDC power source and is supplied with a standard 20 ft. pigtail cable. It can store up to six time and date stamped FirePics™ and 200 events in non-volatile memory. FirePics™ and event histories can be retrieved using a Fire Sentry FS7 Interface Kit and the Fire Sentry Windows-based PC software.

Features:

• Multi-Spectral digital electro-optical radiant energy infrared fire detector
• Unique two-stage fire detection response
• Immune to false alarm sources
• NOT affected by absorbing smoke, gasses or chemical vapors
• NOT sensitive to background radiant energy from electric heaters and ovens
• Detects hydrocarbon and non-hydrocarbon fires
• Rugged leak-proof, heat-sealed, acid-resistant, injection-molded polypropylene housing
• Wide 120° field-of-view
• Digital communication with RS-485 interface
• FirePic™; time and date-stamped digital fire signatures
• Built-in detector automatic self test
• Unitzed model design for stand-alone operation

Applications include:

• Open Areas of Clean Room
• Wet Bench Working Surface
• Wet Bench Subsurface (Plenum)
• Pumps and Equipment Located Behind the Wet Bench Area
• Under-floor Areas
• IPA Stations (Unitized model only)

FS7-2173-2RPT15 FS7 Multi-Spectrum Fire and Flame Detector, 20FT CBL 180IN TFLN VITON 2 RLY by Honeywell Analytics

The Fire Sentry FS7-2173 electro-optical radiant energy fire detector - and the Fire Sentry FS7-2173-2RP (unitized model) with multi-spectral WideBand IR™, Near Band IR and Visible Band fire detection are designed specifically for semiconductor Clean Room fire protection applications.

The Fire Sentry FS7 fire detector provides and intelligent two-stage response to semiconductor wet bench fires:

Stage 1: Alert. This is the first-stage response to a small fire with a heat energy output of 3 kW (the equivalent of a 4-inch diameter polypropylene pool fire). This allows time for the fire to self-extinguish.

Stage 2: Alarm. If the fire does not self-extinguish, and grows to the Factory Mutual specified heat energy threshold of 13 kW (the equivalent of an 8-inch diameter polypropylene pool fire), the second-stage response is activated.

The Fire Sentry FS7-2173 is used with Fire Sentry FS7-130-SX Controller or Control Panel FSWB. Controller and Control Panel supply power to detectors monitor the status of all detectors and communicate with the detectors via the digital RS-485 communication channel. Fire Sentry FS7-2173 is supplied with a standard 20 ft. cable connector. Detectors are connected to the controller or control panel using the self-locking connectors and Fire Sentry junction boxes. This allows for fast and easy connections eliminating wiring problems. Each detector can store up to six time and date stamped FirePics™ (pre-event multi-spectral sensor array data) in non-volatile memory. Controller and control panel can also store event history table in the non-volatile memory, which contains the time and date stamped alert, alarm and fault histories. FirePics™ and event histories can be retrieved from the controller or control panel.

Fire Sentry FS7-2173-2RP unitized model's microprocessor, with digital signal processing algorithms, continuously monitors the circuitry, sensor's built-in selftest and verifies proper operation. Fire Sentry FS7-2173-2RP with discrete relay outputs is designed to operate as a stand-alone detector and interface with any approved fire alarm panel. The detector requires an external 24 VDC power source and is supplied with a standard 20 ft. pigtail cable. It can store up to six time and date stamped FirePics™ and 200 events in non-volatile memory. FirePics™ and event histories can be retrieved using a Fire Sentry FS7 Interface Kit and the Fire Sentry Windows-based PC software.

Features:

• Multi-Spectral digital electro-optical radiant energy infrared fire detector
• Unique two-stage fire detection response
• Immune to false alarm sources
• NOT affected by absorbing smoke, gasses or chemical vapors
• NOT sensitive to background radiant energy from electric heaters and ovens
• Detects hydrocarbon and non-hydrocarbon fires
• Rugged leak-proof, heat-sealed, acid-resistant, injection-molded polypropylene housing
• Wide 120° field-of-view
• Digital communication with RS-485 interface
• FirePic™; time and date-stamped digital fire signatures
• Built-in detector automatic self test
• Unitzed model design for stand-alone operation

Applications include:

• Open Areas of Clean Room
• Wet Bench Working Surface
• Wet Bench Subsurface (Plenum)
• Pumps and Equipment Located Behind the Wet Bench Area
• Under-floor Areas
• IPA Stations (Unitized model only)

FS7-2173-KALO FS7 Multi-Spectrum Fire and Flame Detector, Kal-rez O-ring for use with FS7-130-SX Controller, FSWB Control Panel or S7-2175 Control Panel by Honeywell Analytics

The Fire Sentry FS7-2173 electro-optical radiant energy fire detector - and the Fire Sentry FS7-2173-2RP (unitized model) with multi-spectral WideBand IR™, Near Band IR and Visible Band fire detection are designed specifically for semiconductor Clean Room fire protection applications.

The Fire Sentry FS7 fire detector provides and intelligent two-stage response to semiconductor wet bench fires:

Stage 1: Alert. This is the first-stage response to a small fire with a heat energy output of 3 kW (the equivalent of a 4-inch diameter polypropylene pool fire). This allows time for the fire to self-extinguish.

Stage 2: Alarm. If the fire does not self-extinguish, and grows to the Factory Mutual specified heat energy threshold of 13 kW (the equivalent of an 8-inch diameter polypropylene pool fire), the second-stage response is activated.

The Fire Sentry FS7-2173 is used with Fire Sentry FS7-130-SX Controller or Control Panel FSWB. Controller and Control Panel supply power to detectors monitor the status of all detectors and communicate with the detectors via the digital RS-485 communication channel. Fire Sentry FS7-2173 is supplied with a standard 20 ft. cable connector. Detectors are connected to the controller or control panel using the self-locking connectors and Fire Sentry junction boxes. This allows for fast and easy connections eliminating wiring problems. Each detector can store up to six time and date stamped FirePics™ (pre-event multi-spectral sensor array data) in non-volatile memory. Controller and control panel can also store event history table in the non-volatile memory, which contains the time and date stamped alert, alarm and fault histories. FirePics™ and event histories can be retrieved from the controller or control panel.

Fire Sentry FS7-2173-2RP unitized model's microprocessor, with digital signal processing algorithms, continuously monitors the circuitry, sensor's built-in selftest and verifies proper operation. Fire Sentry FS7-2173-2RP with discrete relay outputs is designed to operate as a stand-alone detector and interface with any approved fire alarm panel. The detector requires an external 24 VDC power source and is supplied with a standard 20 ft. pigtail cable. It can store up to six time and date stamped FirePics™ and 200 events in non-volatile memory. FirePics™ and event histories can be retrieved using a Fire Sentry FS7 Interface Kit and the Fire Sentry Windows-based PC software.

Features:

• Multi-Spectral digital electro-optical radiant energy infrared fire detector
• Unique two-stage fire detection response
• Immune to false alarm sources
• NOT affected by absorbing smoke, gasses or chemical vapors
• NOT sensitive to background radiant energy from electric heaters and ovens
• Detects hydrocarbon and non-hydrocarbon fires
• Rugged leak-proof, heat-sealed, acid-resistant, injection-molded polypropylene housing
• Wide 120° field-of-view
• Digital communication with RS-485 interface
• FirePic™; time and date-stamped digital fire signatures
• Built-in detector automatic self test
• Unitzed model design for stand-alone operation

Applications include:

• Open Areas of Clean Room
• Wet Bench Working Surface
• Wet Bench Subsurface (Plenum)
• Pumps and Equipment Located Behind the Wet Bench Area
• Under-floor Areas
• IPA Stations (Unitized model only)

FS7-2173-RP FS7 Multi-Spectrum Fire and Flame Detector, 20FT CBL 72IN TFLN VITON 1 RLY by Honeywell Analytics

The Fire Sentry FS7-2173 electro-optical radiant energy fire detector - and the Fire Sentry FS7-2173-2RP (unitized model) with multi-spectral WideBand IR™, Near Band IR and Visible Band fire detection are designed specifically for semiconductor Clean Room fire protection applications.

The Fire Sentry FS7 fire detector provides and intelligent two-stage response to semiconductor wet bench fires:

Stage 1: Alert. This is the first-stage response to a small fire with a heat energy output of 3 kW (the equivalent of a 4-inch diameter polypropylene pool fire). This allows time for the fire to self-extinguish.

Stage 2: Alarm. If the fire does not self-extinguish, and grows to the Factory Mutual specified heat energy threshold of 13 kW (the equivalent of an 8-inch diameter polypropylene pool fire), the second-stage response is activated.

The Fire Sentry FS7-2173 is used with Fire Sentry FS7-130-SX Controller or Control Panel FSWB. Controller and Control Panel supply power to detectors monitor the status of all detectors and communicate with the detectors via the digital RS-485 communication channel. Fire Sentry FS7-2173 is supplied with a standard 20 ft. cable connector. Detectors are connected to the controller or control panel using the self-locking connectors and Fire Sentry junction boxes. This allows for fast and easy connections eliminating wiring problems. Each detector can store up to six time and date stamped FirePics™ (pre-event multi-spectral sensor array data) in non-volatile memory. Controller and control panel can also store event history table in the non-volatile memory, which contains the time and date stamped alert, alarm and fault histories. FirePics™ and event histories can be retrieved from the controller or control panel.

Fire Sentry FS7-2173-2RP unitized model's microprocessor, with digital signal processing algorithms, continuously monitors the circuitry, sensor's built-in selftest and verifies proper operation. Fire Sentry FS7-2173-2RP with discrete relay outputs is designed to operate as a stand-alone detector and interface with any approved fire alarm panel. The detector requires an external 24 VDC power source and is supplied with a standard 20 ft. pigtail cable. It can store up to six time and date stamped FirePics™ and 200 events in non-volatile memory. FirePics™ and event histories can be retrieved using a Fire Sentry FS7 Interface Kit and the Fire Sentry Windows-based PC software.

Features:

• Multi-Spectral digital electro-optical radiant energy infrared fire detector
• Unique two-stage fire detection response
• Immune to false alarm sources
• NOT affected by absorbing smoke, gasses or chemical vapors
• NOT sensitive to background radiant energy from electric heaters and ovens
• Detects hydrocarbon and non-hydrocarbon fires
• Rugged leak-proof, heat-sealed, acid-resistant, injection-molded polypropylene housing
• Wide 120° field-of-view
• Digital communication with RS-485 interface
• FirePic™; time and date-stamped digital fire signatures
• Built-in detector automatic self test
• Unitzed model design for stand-alone operation

Applications include:

• Open Areas of Clean Room
• Wet Bench Working Surface
• Wet Bench Subsurface (Plenum)
• Pumps and Equipment Located Behind the Wet Bench Area
• Under-floor Areas
• IPA Stations (Unitized model only)

FS7-2173-RPK FS7 Multi-Spectrum Fire and Flame Detector, 20'C/6'T, KALREZ O-RING by Honeywell Analytics

The Fire Sentry FS7-2173 electro-optical radiant energy fire detector - and the Fire Sentry FS7-2173-2RP (unitized model) with multi-spectral WideBand IR™, Near Band IR and Visible Band fire detection are designed specifically for semiconductor Clean Room fire protection applications.

The Fire Sentry FS7 fire detector provides and intelligent two-stage response to semiconductor wet bench fires:

Stage 1: Alert. This is the first-stage response to a small fire with a heat energy output of 3 kW (the equivalent of a 4-inch diameter polypropylene pool fire). This allows time for the fire to self-extinguish.

Stage 2: Alarm. If the fire does not self-extinguish, and grows to the Factory Mutual specified heat energy threshold of 13 kW (the equivalent of an 8-inch diameter polypropylene pool fire), the second-stage response is activated.

The Fire Sentry FS7-2173 is used with Fire Sentry FS7-130-SX Controller or Control Panel FSWB. Controller and Control Panel supply power to detectors monitor the status of all detectors and communicate with the detectors via the digital RS-485 communication channel. Fire Sentry FS7-2173 is supplied with a standard 20 ft. cable connector. Detectors are connected to the controller or control panel using the self-locking connectors and Fire Sentry junction boxes. This allows for fast and easy connections eliminating wiring problems. Each detector can store up to six time and date stamped FirePics™ (pre-event multi-spectral sensor array data) in non-volatile memory. Controller and control panel can also store event history table in the non-volatile memory, which contains the time and date stamped alert, alarm and fault histories. FirePics™ and event histories can be retrieved from the controller or control panel.

Fire Sentry FS7-2173-2RP unitized model's microprocessor, with digital signal processing algorithms, continuously monitors the circuitry, sensor's built-in selftest and verifies proper operation. Fire Sentry FS7-2173-2RP with discrete relay outputs is designed to operate as a stand-alone detector and interface with any approved fire alarm panel. The detector requires an external 24 VDC power source and is supplied with a standard 20 ft. pigtail cable. It can store up to six time and date stamped FirePics™ and 200 events in non-volatile memory. FirePics™ and event histories can be retrieved using a Fire Sentry FS7 Interface Kit and the Fire Sentry Windows-based PC software.

Features:

• Multi-Spectral digital electro-optical radiant energy infrared fire detector
• Unique two-stage fire detection response
• Immune to false alarm sources
• NOT affected by absorbing smoke, gasses or chemical vapors
• NOT sensitive to background radiant energy from electric heaters and ovens
• Detects hydrocarbon and non-hydrocarbon fires
• Rugged leak-proof, heat-sealed, acid-resistant, injection-molded polypropylene housing
• Wide 120° field-of-view
• Digital communication with RS-485 interface
• FirePic™; time and date-stamped digital fire signatures
• Built-in detector automatic self test
• Unitzed model design for stand-alone operation

Applications include:

• Open Areas of Clean Room
• Wet Bench Working Surface
• Wet Bench Subsurface (Plenum)
• Pumps and Equipment Located Behind the Wet Bench Area
• Under-floor Areas
• IPA Stations (Unitized model only)

FSL100-IR3-W FSL100 IR3 Flame Detector, White Housing by Honeywell Analytics

The FSL100 Series of flame detectors from Honeywell delivers robust, fast, and reliable detection of flaming fires in a wide range of applications.

The range consists of UV, UV/IR and IR3 flame detectors. All utilize sophisticated sensing and signal analysis to detect fires quickly while also rejecting false alarms.

The FSL100 may be small and lightweight for easy installation but it is designed to work in tough indoor/outdoor environments, as well as potentially explosive atmospheres.

With a large field of view it can detect a range of different types of fire including hydrocarbon and non-hydrocarbon sources. Available in UV, UV/IR and 3IR we have your application covered.

Suitable for Many Applications

• UV, UV/IR and IR3 available
• Hydrocarbon and non-hydrocarbon sources
• Use in potentially explosive atmospheres
• Indoor and outdoor operation
• High visibility red or discrete white models available

Great Performance

• Approved to EN54-10 and FM3260 flame detector standards
• Comprehensive automatic self test
• Remote manual self test option

Fast & Reliable

• High speed sensors and microprocessor
• Sophisticated analysis algorithms
• Continuous health monitoring
• False alarm rejection

Reduced Life Cost

• Long life elements
• Pressure compensation to avoid contamination
• 2 year warranty
• Buy with confidence

Ease of Installation and Use

• Relay and mA outputs as standard
• Lightweight GRP housing
• Pre-formed knockouts
• Optional swivel mounting bracket
• Long range test lamp available

FSL100-UV

• Suitable for indoor applications; for example fume hoods and hydrogen storage areas
• Effective solution for materials burning with low temperatures, e.g. Sulphur
• Alarms to fires from heavy hydrocarbons (wood, paper, petroleum, etc.), light hydrocarbons (methanol, methane, etc.), and hydrogen
• Good resistance against the influences of: 1) Direct and reflected sunlight, 2) Artificial light, such as fluorescent tubes and glass covered halogen lamps

FSL100-UV/IR

• Analysis of the flame flicker-frequency for improved false alarm rejection
• Dual sensing methodology enables a wide range of hydrocarbon and non-hydrocarbon fires to be effectively detected
• Good resistance against the influences of: 1) Direct and reflected sunlight, 2) Artificial light, such as fluorescent tubes and glass covered halogen lamps, 3) Arcs and electric discharges (staticor from e.g. electric motors), 4) The radiation from electric welding provided that the electric welding takes place at a distance more than 10 feet from the flame detector (a welding rod contains organic compounds which may produce a small flame)

FSL100-IR3

• Analysis of the flame flicker frequency for improved false alarm rejection
• Particularly suited to liquid hydrocarbon and dirty fires
• Affected less by window contamination or smoky fires
• Good resistance against the influences of: 1) Direct and reflected sunlight, 2) Artificial light, such as fluorescent tubes and glass covered halogen lamps, 3) Arcs and electric discharges (static or from e.g. electric motors), 4) The radiation from electric welding provided that the electric welding takes place at a distance more than 10 feet from the flame detector (a welding rod contains organic compounds which may produce a small flame)
• Especially suitable fires that emit large amounts of smoke

FSL100-UV-W FSL100 UV Flame Detector, White Housing by Honeywell Analytics

The FSL100 Series of flame detectors from Honeywell delivers robust, fast, and reliable detection of flaming fires in a wide range of applications.

The range consists of UV, UV/IR and IR3 flame detectors. All utilize sophisticated sensing and signal analysis to detect fires quickly while also rejecting false alarms.

The FSL100 may be small and lightweight for easy installation but it is designed to work in tough indoor/outdoor environments, as well as potentially explosive atmospheres.

With a large field of view it can detect a range of different types of fire including hydrocarbon and non-hydrocarbon sources. Available in UV, UV/IR and 3IR we have your application covered.

Suitable for Many Applications

• UV, UV/IR and IR3 available
• Hydrocarbon and non-hydrocarbon sources
• Use in potentially explosive atmospheres
• Indoor and outdoor operation
• High visibility red or discrete white models available

Great Performance

• Approved to EN54-10 and FM3260 flame detector standards
• Comprehensive automatic self test
• Remote manual self test option

Fast & Reliable

• High speed sensors and microprocessor
• Sophisticated analysis algorithms
• Continuous health monitoring
• False alarm rejection

Reduced Life Cost

• Long life elements
• Pressure compensation to avoid contamination
• 2 year warranty
• Buy with confidence

Ease of Installation and Use

• Relay and mA outputs as standard
• Lightweight GRP housing
• Pre-formed knockouts
• Optional swivel mounting bracket
• Long range test lamp available

FSL100-UV

• Suitable for indoor applications; for example fume hoods and hydrogen storage areas
• Effective solution for materials burning with low temperatures, e.g. Sulphur
• Alarms to fires from heavy hydrocarbons (wood, paper, petroleum, etc.), light hydrocarbons (methanol, methane, etc.), and hydrogen
• Good resistance against the influences of: 1) Direct and reflected sunlight, 2) Artificial light, such as fluorescent tubes and glass covered halogen lamps

FSL100-UV/IR

• Analysis of the flame flicker-frequency for improved false alarm rejection
• Dual sensing methodology enables a wide range of hydrocarbon and non-hydrocarbon fires to be effectively detected
• Good resistance against the influences of: 1) Direct and reflected sunlight, 2) Artificial light, such as fluorescent tubes and glass covered halogen lamps, 3) Arcs and electric discharges (staticor from e.g. electric motors), 4) The radiation from electric welding provided that the electric welding takes place at a distance more than 10 feet from the flame detector (a welding rod contains organic compounds which may produce a small flame)

FSL100-IR3

• Analysis of the flame flicker frequency for improved false alarm rejection
• Particularly suited to liquid hydrocarbon and dirty fires
• Affected less by window contamination or smoky fires
• Good resistance against the influences of: 1) Direct and reflected sunlight, 2) Artificial light, such as fluorescent tubes and glass covered halogen lamps, 3) Arcs and electric discharges (static or from e.g. electric motors), 4) The radiation from electric welding provided that the electric welding takes place at a distance more than 10 feet from the flame detector (a welding rod contains organic compounds which may produce a small flame)
• Especially suitable fires that emit large amounts of smoke

G01-0101-010 ToxiRAE 3 Portable Single-Gas Monitor - CO, 0-500 PPM (Pack of 10) by RAE Systems

The ToxiRAE 3 is a full-featured single-gas monitor that offers unequaled value. The ToxiRAE 3 is compatible with the AutoRAE Lite bump test and calibration station, one of the fastest on the market, so that the monitors can be put back to work quickly. The detector features a 2-year warranty and can record STEL, TWA, high, and low alarms.

ToxiRAE 3 Pack of 10 includes

• (10/ea) ToxiRAE 3 monitor with H2S, CO or CO (High Range) sensor (as specified)
• (2) CDs with Operation Manual
• (10) Rugged alligator clips
• (2) Functional gas test adapters
• (10) Calibration certificates
• (2) Quick start guide

Key Features

• High-performance, 3-electrode, pinless micro sensor with the fastest response time in the industry
• 0.1 ppm H2S resolution, and high-range 1999 ppm CO available
• Large, easy-to-read and user-configurable display (concentration or days remaining)
• Event logging of up to 10 events
• Data downloads and monitor configuration via the AutoRAE Lite calibration station
• IP-67 water- and dust-resistant
• Loud, 95 dB audible alarm, bright red flashing LEDs, and internal vibration alarm
• Extended operating temperature of -4° to 140° F (-20° to +60° C) with full T4 approval
• User-configurable bump/calibration reminders

Applications

• Emergency response
• Environmental
• Fire service
• Industrial safety
• Oil and gas

G01-0103-010 ToxiRAE 3 Portable Single-Gas Monitor - CO, 0-1999 PPM (Pack of 10) by RAE Systems

The ToxiRAE 3 is a full-featured single-gas monitor that offers unequaled value. The ToxiRAE 3 is compatible with the AutoRAE Lite bump test and calibration station, one of the fastest on the market, so that the monitors can be put back to work quickly. The detector features a 2-year warranty and can record STEL, TWA, high, and low alarms.

ToxiRAE 3 Pack of 10 includes

• (10/ea) ToxiRAE 3 monitor with H2S, CO or CO (High Range) sensor (as specified)
• (2) CDs with Operation Manual
• (10) Rugged alligator clips
• (2) Functional gas test adapters
• (10) Calibration certificates
• (2) Quick start guide

Key Features

• High-performance, 3-electrode, pinless micro sensor with the fastest response time in the industry
• 0.1 ppm H2S resolution, and high-range 1999 ppm CO available
• Large, easy-to-read and user-configurable display (concentration or days remaining)
• Event logging of up to 10 events
• Data downloads and monitor configuration via the AutoRAE Lite calibration station
• IP-67 water- and dust-resistant
• Loud, 95 dB audible alarm, bright red flashing LEDs, and internal vibration alarm
• Extended operating temperature of -4° to 140° F (-20° to +60° C) with full T4 approval
• User-configurable bump/calibration reminders

Applications

• Emergency response
• Environmental
• Fire service
• Industrial safety
• Oil and gas

G01-0107-010 ToxiRAE 3 Portable Single-Gas Monitor - H2S, 0-100 PPM (Pack of 10) by RAE Systems

The ToxiRAE 3 is a full-featured single-gas monitor that offers unequaled value. The ToxiRAE 3 is compatible with the AutoRAE Lite bump test and calibration station, one of the fastest on the market, so that the monitors can be put back to work quickly. The detector features a 2-year warranty and can record STEL, TWA, high, and low alarms.

ToxiRAE 3 Pack of 10 includes

• (10/ea) ToxiRAE 3 monitor with H2S, CO or CO (High Range) sensor (as specified)
• (2) CDs with Operation Manual
• (10) Rugged alligator clips
• (2) Functional gas test adapters
• (10) Calibration certificates
• (2) Quick start guide

Key Features

• High-performance, 3-electrode, pinless micro sensor with the fastest response time in the industry
• 0.1 ppm H2S resolution, and high-range 1999 ppm CO available
• Large, easy-to-read and user-configurable display (concentration or days remaining)
• Event logging of up to 10 events
• Data downloads and monitor configuration via the AutoRAE Lite calibration station
• IP-67 water- and dust-resistant
• Loud, 95 dB audible alarm, bright red flashing LEDs, and internal vibration alarm
• Extended operating temperature of -4° to 140° F (-20° to +60° C) with full T4 approval
• User-configurable bump/calibration reminders

Applications

• Emergency response
• Environmental
• Fire service
• Industrial safety
• Oil and gas

G02-B020-000 ToxiRAE Pro PID Personal Monitor - 9.8 eV PID Lamp, Datalogging, Rechargeable Battery, Rubber Boot by RAE Systems

The ToxiRAE Pro PID is the world's smallest volatile organic compound (VOC) monitor. Featuring RAE Systems' next-generation PID sensor, the ToxiRAE Pro PID can quickly detect and accurately monitor over 300 VOCs. The ToxiRAE Pro PID provides safety professionals wireless remote access to real-time instrument readings and alarm status for better visibility and faster incident response. With an onboard library of 190 correction factors, the ToxiRAE Pro PID can be programmed to automatically read in equivalent units of the specified compound.

ToxiRAE Pro PID comes with

• ToxiRAE Pro PID monitor with sensor and wireless option as specified, rechargeable battery, alligator clip, and protective rubber boot installed
• Charging and PC communication cradle
• PC communication cable
• AC adapter (100 to 240 V, 50/60 Hz AC to 12 V DC)
• Calibration adapter
• Combined instrument / sensor cap removal tool
• Quick Start Guide
• CD with documentation
• CD with ProRAE Studio II monitor configuration & data management software
• Technical Note TN-106 with ionization energies and correction factors for 300+ VOCs (Industrial Hygiene versions only)
• Calibration and test certificate
• Warranty/registration card

Key Features

• Wireless access to real-time instrument readings and alarm status from any location
• Unmistakable five-way local and remote wireless notification of alarm conditions
• Largest display in its class
• Continuous datalogging
• On-board correction factor library for 190 compounds
• Easy to use
• Reliable, rugged, and intrinsically safe

Applications for Industrial hygiene and safety

• Chemical plants
• Government health, Safety, Security, and environmental agencies
• Hazardous materials teams, first responders
• Oil and gas
• Pharmaceutical plants

Applications for Environmental applications

• Environmental consulting
• Soil remediation

G02-B024-000 ToxiRAE Pro PID Personal Monitor - 9.8 eV PID Lamp, Datalogging, Wireless, Rechargeable Battery, Rubber Boot by RAE Systems

The ToxiRAE Pro PID is the world's smallest volatile organic compound (VOC) monitor. Featuring RAE Systems' next-generation PID sensor, the ToxiRAE Pro PID can quickly detect and accurately monitor over 300 VOCs. The ToxiRAE Pro PID provides safety professionals wireless remote access to real-time instrument readings and alarm status for better visibility and faster incident response. With an onboard library of 190 correction factors, the ToxiRAE Pro PID can be programmed to automatically read in equivalent units of the specified compound.

ToxiRAE Pro PID comes with

• ToxiRAE Pro PID monitor with sensor and wireless option as specified, rechargeable battery, alligator clip, and protective rubber boot installed
• Charging and PC communication cradle
• PC communication cable
• AC adapter (100 to 240 V, 50/60 Hz AC to 12 V DC)
• Calibration adapter
• Combined instrument / sensor cap removal tool
• Quick Start Guide
• CD with documentation
• CD with ProRAE Studio II monitor configuration & data management software
• Technical Note TN-106 with ionization energies and correction factors for 300+ VOCs (Industrial Hygiene versions only)
• Calibration and test certificate
• Warranty/registration card

Key Features

• Wireless access to real-time instrument readings and alarm status from any location
• Unmistakable five-way local and remote wireless notification of alarm conditions
• Largest display in its class
• Continuous datalogging
• On-board correction factor library for 190 compounds
• Easy to use
• Reliable, rugged, and intrinsically safe

Applications for Industrial hygiene and safety

• Chemical plants
• Government health, Safety, Security, and environmental agencies
• Hazardous materials teams, first responders
• Oil and gas
• Pharmaceutical plants

Applications for Environmental applications

• Environmental consulting
• Soil remediation

G450-11065C G450 Confined Space Kit, Rechargeable Battery with Rechargeable Smart Pump, O2, LEL by GfG

GfG is one of the industry s leading producers of workplace safety products. Their products are safe, reliable, and customizable. Their state of the art research and development facility produces the most advanced products on the market. Additionally, their dedicated team of safety professionals works to ensure that each product can be equipped with customization tools and modifications to ensure that each product can be optimized to meet the most rigorous workplace safety standards. Introducing the G450 Multi-gas Detector, GfG is continuing its legacy as a safety leader.

G450 Multi-gas Detector

The G450 Multi-gas Detector continually measures up to four separate atmospheric gases. In confined spaces, the detector will monitor LEL combustible gas, oxygen, H2S, and CO. The easy to use G450 series of detectors is designed with user friendliness in mind. Many of its most common functions are operated with a single button, and the unit features a fully automatic calibration system. Users need only to attach the adaptor and flow gas to the sensors. The unit s GfG AutoCal system will automatically initiate the calibration sequence and will update the necessary information on the G450 Multi-gas Detector.

Long Battery Life

The G450 Multi-gas Detector also features a long life battery operation that is most efficient for workplace safety. The device has a batter life of up to 25 hours of continuous operation. With alkaline packs, the units are powered by 2 AA batteries, and when placed in the drop in cradle, the rechargeable battery packs can be fully recharged in less than 4 hours. The rechargeable packs have optional flash light LEDs to indicate charge level.

Triple Alarm System

This unit features an elaborate alarm system that is not to be missed. The triple alarm system features a loud audible alarm of 103dB, a vibrating alarm, and bright 360 wrap around LEDs with a colored backlit display for visual alarms. The alarm system ensures that users and those nearby are fully aware of possible environmental hazards. Additionally, the easy to read backlit display will light varying colors from green, orange, and red to intuitively notify users of the severity of the conditions.

Features

The G450 Multi-gas Detector is encased in a dust proof and highly water resistant housing. The housing even contains a built in rubber boot to help protect from regular wear and tear. Each unit is equipped with datalogging capabilities. The datalogger records and internally stores all activity and environmental conditions. Users can download this information to their computers and use it to research, analyze, and evaluate the jobsite environment.

The multi-gas detection system comes standard with a few accessories including a calibration adaptor, a training manual, and a training DVD. The rechargeable devices include the previous accessories and additional drop in cradle chargers and a wall power adaptor. Optional accessories include a datalogging kit, self powered attachable motorized sample pump, spare battery packs, and rechargeable battery packs. The breadth of available accessories helps to ensure that the G450 Multi-gas Detector can be customized to meet the needs of individual work spaces.

G450-11165C G450 Confined Space Kit, Rechargeable Battery with Rechargeable Smart Pump, O2, LEL, CO by GfG

GfG is one of the industry s leading producers of workplace safety products. Their products are safe, reliable, and customizable. Their state of the art research and development facility produces the most advanced products on the market. Additionally, their dedicated team of safety professionals works to ensure that each product can be equipped with customization tools and modifications to ensure that each product can be optimized to meet the most rigorous workplace safety standards. Introducing the G450 Multi-gas Detector, GfG is continuing its legacy as a safety leader.

G450 Multi-gas Detector

The G450 Multi-gas Detector continually measures up to four separate atmospheric gases. In confined spaces, the detector will monitor LEL combustible gas, oxygen, H2S, and CO. The easy to use G450 series of detectors is designed with user friendliness in mind. Many of its most common functions are operated with a single button, and the unit features a fully automatic calibration system. Users need only to attach the adaptor and flow gas to the sensors. The unit s GfG AutoCal system will automatically initiate the calibration sequence and will update the necessary information on the G450 Multi-gas Detector.

Long Battery Life

The G450 Multi-gas Detector also features a long life battery operation that is most efficient for workplace safety. The device has a batter life of up to 25 hours of continuous operation. With alkaline packs, the units are powered by 2 AA batteries, and when placed in the drop in cradle, the rechargeable battery packs can be fully recharged in less than 4 hours. The rechargeable packs have optional flash light LEDs to indicate charge level.

Triple Alarm System

This unit features an elaborate alarm system that is not to be missed. The triple alarm system features a loud audible alarm of 103dB, a vibrating alarm, and bright 360 wrap around LEDs with a colored backlit display for visual alarms. The alarm system ensures that users and those nearby are fully aware of possible environmental hazards. Additionally, the easy to read backlit display will light varying colors from green, orange, and red to intuitively notify users of the severity of the conditions.

Features

The G450 Multi-gas Detector is encased in a dust proof and highly water resistant housing. The housing even contains a built in rubber boot to help protect from regular wear and tear. Each unit is equipped with datalogging capabilities. The datalogger records and internally stores all activity and environmental conditions. Users can download this information to their computers and use it to research, analyze, and evaluate the jobsite environment.

The multi-gas detection system comes standard with a few accessories including a calibration adaptor, a training manual, and a training DVD. The rechargeable devices include the previous accessories and additional drop in cradle chargers and a wall power adaptor. Optional accessories include a datalogging kit, self powered attachable motorized sample pump, spare battery packs, and rechargeable battery packs. The breadth of available accessories helps to ensure that the G450 Multi-gas Detector can be customized to meet the needs of individual work spaces.

G450-11166C G450 Confined Space Kit, Rechargeable Battery with Flashlight Rechargeable Smart Pump, O2, LEL, CO by GfG

GfG is one of the industry s leading producers of workplace safety products. Their products are safe, reliable, and customizable. Their state of the art research and development facility produces the most advanced products on the market. Additionally, their dedicated team of safety professionals works to ensure that each product can be equipped with customization tools and modifications to ensure that each product can be optimized to meet the most rigorous workplace safety standards. Introducing the G450 Multi-gas Detector, GfG is continuing its legacy as a safety leader.

G450 Multi-gas Detector

The G450 Multi-gas Detector continually measures up to four separate atmospheric gases. In confined spaces, the detector will monitor LEL combustible gas, oxygen, H2S, and CO. The easy to use G450 series of detectors is designed with user friendliness in mind. Many of its most common functions are operated with a single button, and the unit features a fully automatic calibration system. Users need only to attach the adaptor and flow gas to the sensors. The unit s GfG AutoCal system will automatically initiate the calibration sequence and will update the necessary information on the G450 Multi-gas Detector.

Long Battery Life

The G450 Multi-gas Detector also features a long life battery operation that is most efficient for workplace safety. The device has a batter life of up to 25 hours of continuous operation. With alkaline packs, the units are powered by 2 AA batteries, and when placed in the drop in cradle, the rechargeable battery packs can be fully recharged in less than 4 hours. The rechargeable packs have optional flash light LEDs to indicate charge level.

Triple Alarm System

This unit features an elaborate alarm system that is not to be missed. The triple alarm system features a loud audible alarm of 103dB, a vibrating alarm, and bright 360 wrap around LEDs with a colored backlit display for visual alarms. The alarm system ensures that users and those nearby are fully aware of possible environmental hazards. Additionally, the easy to read backlit display will light varying colors from green, orange, and red to intuitively notify users of the severity of the conditions.

Features

The G450 Multi-gas Detector is encased in a dust proof and highly water resistant housing. The housing even contains a built in rubber boot to help protect from regular wear and tear. Each unit is equipped with datalogging capabilities. The datalogger records and internally stores all activity and environmental conditions. Users can download this information to their computers and use it to research, analyze, and evaluate the jobsite environment.

The multi-gas detection system comes standard with a few accessories including a calibration adaptor, a training manual, and a training DVD. The rechargeable devices include the previous accessories and additional drop in cradle chargers and a wall power adaptor. Optional accessories include a datalogging kit, self powered attachable motorized sample pump, spare battery packs, and rechargeable battery packs. The breadth of available accessories helps to ensure that the G450 Multi-gas Detector can be customized to meet the needs of individual work spaces.

G450-11166K G450 Value Kit, Rechargeable Battery with Flashlight Rechargeable Smart Pump, O2, LEL, CO by GfG

GfG is one of the industry s leading producers of workplace safety products. Their products are safe, reliable, and customizable. Their state of the art research and development facility produces the most advanced products on the market. Additionally, their dedicated team of safety professionals works to ensure that each product can be equipped with customization tools and modifications to ensure that each product can be optimized to meet the most rigorous workplace safety standards. Introducing the G450 Multi-gas Detector, GfG is continuing its legacy as a safety leader.

G450 Multi-gas Detector

The G450 Multi-gas Detector continually measures up to four separate atmospheric gases. In confined spaces, the detector will monitor LEL combustible gas, oxygen, H2S, and CO. The easy to use G450 series of detectors is designed with user friendliness in mind. Many of its most common functions are operated with a single button, and the unit features a fully automatic calibration system. Users need only to attach the adaptor and flow gas to the sensors. The unit s GfG AutoCal system will automatically initiate the calibration sequence and will update the necessary information on the G450 Multi-gas Detector.

Long Battery Life

The G450 Multi-gas Detector also features a long life battery operation that is most efficient for workplace safety. The device has a batter life of up to 25 hours of continuous operation. With alkaline packs, the units are powered by 2 AA batteries, and when placed in the drop in cradle, the rechargeable battery packs can be fully recharged in less than 4 hours. The rechargeable packs have optional flash light LEDs to indicate charge level.

Triple Alarm System

This unit features an elaborate alarm system that is not to be missed. The triple alarm system features a loud audible alarm of 103dB, a vibrating alarm, and bright 360 wrap around LEDs with a colored backlit display for visual alarms. The alarm system ensures that users and those nearby are fully aware of possible environmental hazards. Additionally, the easy to read backlit display will light varying colors from green, orange, and red to intuitively notify users of the severity of the conditions.

Features

The G450 Multi-gas Detector is encased in a dust proof and highly water resistant housing. The housing even contains a built in rubber boot to help protect from regular wear and tear. Each unit is equipped with datalogging capabilities. The datalogger records and internally stores all activity and environmental conditions. Users can download this information to their computers and use it to research, analyze, and evaluate the jobsite environment.

The multi-gas detection system comes standard with a few accessories including a calibration adaptor, a training manual, and a training DVD. The rechargeable devices include the previous accessories and additional drop in cradle chargers and a wall power adaptor. Optional accessories include a datalogging kit, self powered attachable motorized sample pump, spare battery packs, and rechargeable battery packs. The breadth of available accessories helps to ensure that the G450 Multi-gas Detector can be customized to meet the needs of individual work spaces.

G450-11265K G450 Value Kit, Rechargeable Battery with Rechargeable Smart Pump, O2, LEL, H2S by GfG

GfG is one of the industry s leading producers of workplace safety products. Their products are safe, reliable, and customizable. Their state of the art research and development facility produces the most advanced products on the market. Additionally, their dedicated team of safety professionals works to ensure that each product can be equipped with customization tools and modifications to ensure that each product can be optimized to meet the most rigorous workplace safety standards. Introducing the G450 Multi-gas Detector, GfG is continuing its legacy as a safety leader.

G450 Multi-gas Detector

The G450 Multi-gas Detector continually measures up to four separate atmospheric gases. In confined spaces, the detector will monitor LEL combustible gas, oxygen, H2S, and CO. The easy to use G450 series of detectors is designed with user friendliness in mind. Many of its most common functions are operated with a single button, and the unit features a fully automatic calibration system. Users need only to attach the adaptor and flow gas to the sensors. The unit s GfG AutoCal system will automatically initiate the calibration sequence and will update the necessary information on the G450 Multi-gas Detector.

Long Battery Life

The G450 Multi-gas Detector also features a long life battery operation that is most efficient for workplace safety. The device has a batter life of up to 25 hours of continuous operation. With alkaline packs, the units are powered by 2 AA batteries, and when placed in the drop in cradle, the rechargeable battery packs can be fully recharged in less than 4 hours. The rechargeable packs have optional flash light LEDs to indicate charge level.

Triple Alarm System

This unit features an elaborate alarm system that is not to be missed. The triple alarm system features a loud audible alarm of 103dB, a vibrating alarm, and bright 360 wrap around LEDs with a colored backlit display for visual alarms. The alarm system ensures that users and those nearby are fully aware of possible environmental hazards. Additionally, the easy to read backlit display will light varying colors from green, orange, and red to intuitively notify users of the severity of the conditions.

Features

The G450 Multi-gas Detector is encased in a dust proof and highly water resistant housing. The housing even contains a built in rubber boot to help protect from regular wear and tear. Each unit is equipped with datalogging capabilities. The datalogger records and internally stores all activity and environmental conditions. Users can download this information to their computers and use it to research, analyze, and evaluate the jobsite environment.

The multi-gas detection system comes standard with a few accessories including a calibration adaptor, a training manual, and a training DVD. The rechargeable devices include the previous accessories and additional drop in cradle chargers and a wall power adaptor. Optional accessories include a datalogging kit, self powered attachable motorized sample pump, spare battery packs, and rechargeable battery packs. The breadth of available accessories helps to ensure that the G450 Multi-gas Detector can be customized to meet the needs of individual work spaces.

G450-11044C G450 Confined Space Kit, Flashlight RechargeableBattery with Alkaline Smart Pump, O2, LEL, CO, H2S by GfG

GfG is one of the industry s leading producers of workplace safety products. Their products are safe, reliable, and customizable. Their state of the art research and development facility produces the most advanced products on the market. Additionally, their dedicated team of safety professionals works to ensure that each product can be equipped with customization tools and modifications to ensure that each product can be optimized to meet the most rigorous workplace safety standards. Introducing the G450 Multi-gas Detector, GfG is continuing its legacy as a safety leader.

G450 Multi-gas Detector

The G450 Multi-gas Detector continually measures up to four separate atmospheric gases. In confined spaces, the detector will monitor LEL combustible gas, oxygen, H2S, and CO. The easy to use G450 series of detectors is designed with user friendliness in mind. Many of its most common functions are operated with a single button, and the unit features a fully automatic calibration system. Users need only to attach the adaptor and flow gas to the sensors. The unit s GfG AutoCal system will automatically initiate the calibration sequence and will update the necessary information on the G450 Multi-gas Detector.

Long Battery Life

The G450 Multi-gas Detector also features a long life battery operation that is most efficient for workplace safety. The device has a batter life of up to 25 hours of continuous operation. With alkaline packs, the units are powered by 2 AA batteries, and when placed in the drop in cradle, the rechargeable battery packs can be fully recharged in less than 4 hours. The rechargeable packs have optional flash light LEDs to indicate charge level.

Triple Alarm System

This unit features an elaborate alarm system that is not to be missed. The triple alarm system features a loud audible alarm of 103dB, a vibrating alarm, and bright 360 wrap around LEDs with a colored backlit display for visual alarms. The alarm system ensures that users and those nearby are fully aware of possible environmental hazards. Additionally, the easy to read backlit display will light varying colors from green, orange, and red to intuitively notify users of the severity of the conditions.

Features

The G450 Multi-gas Detector is encased in a dust proof and highly water resistant housing. The housing even contains a built in rubber boot to help protect from regular wear and tear. Each unit is equipped with datalogging capabilities. The datalogger records and internally stores all activity and environmental conditions. Users can download this information to their computers and use it to research, analyze, and evaluate the jobsite environment.

The multi-gas detection system comes standard with a few accessories including a calibration adaptor, a training manual, and a training DVD. The rechargeable devices include the previous accessories and additional drop in cradle chargers and a wall power adaptor. Optional accessories include a datalogging kit, self powered attachable motorized sample pump, spare battery packs, and rechargeable battery packs. The breadth of available accessories helps to ensure that the G450 Multi-gas Detector can be customized to meet the needs of individual work spaces.

G450-11465K G450 Value Kit, Rechargeable Battery with Rechargeable Smart Pump, O2, LEL, CO, H2S by GfG

GfG is one of the industry s leading producers of workplace safety products. Their products are safe, reliable, and customizable. Their state of the art research and development facility produces the most advanced products on the market. Additionally, their dedicated team of safety professionals works to ensure that each product can be equipped with customization tools and modifications to ensure that each product can be optimized to meet the most rigorous workplace safety standards. Introducing the G450 Multi-gas Detector, GfG is continuing its legacy as a safety leader.

G450 Multi-gas Detector

The G450 Multi-gas Detector continually measures up to four separate atmospheric gases. In confined spaces, the detector will monitor LEL combustible gas, oxygen, H2S, and CO. The easy to use G450 series of detectors is designed with user friendliness in mind. Many of its most common functions are operated with a single button, and the unit features a fully automatic calibration system. Users need only to attach the adaptor and flow gas to the sensors. The unit s GfG AutoCal system will automatically initiate the calibration sequence and will update the necessary information on the G450 Multi-gas Detector.

Long Battery Life

The G450 Multi-gas Detector also features a long life battery operation that is most efficient for workplace safety. The device has a batter life of up to 25 hours of continuous operation. With alkaline packs, the units are powered by 2 AA batteries, and when placed in the drop in cradle, the rechargeable battery packs can be fully recharged in less than 4 hours. The rechargeable packs have optional flash light LEDs to indicate charge level.

Triple Alarm System

This unit features an elaborate alarm system that is not to be missed. The triple alarm system features a loud audible alarm of 103dB, a vibrating alarm, and bright 360 wrap around LEDs with a colored backlit display for visual alarms. The alarm system ensures that users and those nearby are fully aware of possible environmental hazards. Additionally, the easy to read backlit display will light varying colors from green, orange, and red to intuitively notify users of the severity of the conditions.

Features

The G450 Multi-gas Detector is encased in a dust proof and highly water resistant housing. The housing even contains a built in rubber boot to help protect from regular wear and tear. Each unit is equipped with datalogging capabilities. The datalogger records and internally stores all activity and environmental conditions. Users can download this information to their computers and use it to research, analyze, and evaluate the jobsite environment.

The multi-gas detection system comes standard with a few accessories including a calibration adaptor, a training manual, and a training DVD. The rechargeable devices include the previous accessories and additional drop in cradle chargers and a wall power adaptor. Optional accessories include a datalogging kit, self powered attachable motorized sample pump, spare battery packs, and rechargeable battery packs. The breadth of available accessories helps to ensure that the G450 Multi-gas Detector can be customized to meet the needs of individual work spaces.

G450-11466K G450 Value Kit, Rechargeable Battery with Flashlight Rechargeable Smart Pump, O2, LEL, CO, H2S by GfG

GfG is one of the industry s leading producers of workplace safety products. Their products are safe, reliable, and customizable. Their state of the art research and development facility produces the most advanced products on the market. Additionally, their dedicated team of safety professionals works to ensure that each product can be equipped with customization tools and modifications to ensure that each product can be optimized to meet the most rigorous workplace safety standards. Introducing the G450 Multi-gas Detector, GfG is continuing its legacy as a safety leader.

G450 Multi-gas Detector

The G450 Multi-gas Detector continually measures up to four separate atmospheric gases. In confined spaces, the detector will monitor LEL combustible gas, oxygen, H2S, and CO. The easy to use G450 series of detectors is designed with user friendliness in mind. Many of its most common functions are operated with a single button, and the unit features a fully automatic calibration system. Users need only to attach the adaptor and flow gas to the sensors. The unit s GfG AutoCal system will automatically initiate the calibration sequence and will update the necessary information on the G450 Multi-gas Detector.

Long Battery Life

The G450 Multi-gas Detector also features a long life battery operation that is most efficient for workplace safety. The device has a batter life of up to 25 hours of continuous operation. With alkaline packs, the units are powered by 2 AA batteries, and when placed in the drop in cradle, the rechargeable battery packs can be fully recharged in less than 4 hours. The rechargeable packs have optional flash light LEDs to indicate charge level.

Triple Alarm System

This unit features an elaborate alarm system that is not to be missed. The triple alarm system features a loud audible alarm of 103dB, a vibrating alarm, and bright 360 wrap around LEDs with a colored backlit display for visual alarms. The alarm system ensures that users and those nearby are fully aware of possible environmental hazards. Additionally, the easy to read backlit display will light varying colors from green, orange, and red to intuitively notify users of the severity of the conditions.

Features

The G450 Multi-gas Detector is encased in a dust proof and highly water resistant housing. The housing even contains a built in rubber boot to help protect from regular wear and tear. Each unit is equipped with datalogging capabilities. The datalogger records and internally stores all activity and environmental conditions. Users can download this information to their computers and use it to research, analyze, and evaluate the jobsite environment.

The multi-gas detection system comes standard with a few accessories including a calibration adaptor, a training manual, and a training DVD. The rechargeable devices include the previous accessories and additional drop in cradle chargers and a wall power adaptor. Optional accessories include a datalogging kit, self powered attachable motorized sample pump, spare battery packs, and rechargeable battery packs. The breadth of available accessories helps to ensure that the G450 Multi-gas Detector can be customized to meet the needs of individual work spaces.