$2000 - $4000

2811-740-003 EC 28 Gas Transmitter with Hydrogen Fluoride (HF) Sensor, 0 - 10 ppm Range, Display / Alarm by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG's proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds - just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm - Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG's GMA controller.

The EC 28 DA provides additional bright alarm LEDs and a buzzer - avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor - sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

Sperian Biosystems PhD6 Multigas Detector

The Biosystems PhD6 Multigas Detector is the latest development in compact multigas detection systems. The detector is proven to be compact, efficient, and cost effective. With dual alarm systems featuring ultra-loud audible indicators and ultra-bright LED visual indicators, users and those nearby are always notified when potential hazards may be present. When developing this detector, the engineers at SperianProtection Instrumentation also developed an express docking station that would reduce calibration time and labor costs. The detection and docking station help users meet record keeping requirements and reduce the risks of human error. With the SperianBiosystems PhD6 Multigas Detector, users can rest assured that they are receiving the very best in gas detection technology.

Key Features

The Biosystems PhD6 Multigas Detector is compatible with over 19 sensor choices including:

• PID
• IR-CO2
• IR-CH4
• Conventional LEL
• Oxygen
• 15 different toxic gas sensors

The gas detector is encased in a durable solid polycarbonate case with a rubber over mold for easy handling. It has an interchangeable battery pack with both Alkaline and Li-Ion rechargeable batteries. Both battery types offer up to 24 hour run times. The unit features dual audible alarms at 92 decibels and front and side ultra-bright LED visual alarms to ensure that the user and those nearby are always notified of possible hazardous conditions. For easy interpretation, the detector has an easy to read status bar and large LCD display that notifies users of the device s functionality and calibration due date. Using the menu options, users can easily adjust a variety of the instrument s settings.

Automatic Docking Station

When developing the PhD6 Multigas Detector, product developers also created an automatic docking station (Biosystems IQ6 Express Dock) to be fully compatible with the detector. The docking station aims to reduce labor time and costs by fully automating certain aspects of instrument maintenance including calibration, functionality testing, and record keeping. Using the Express Dock, users can maintain compliance with recordkeeping requirements by simply docking the detector in the station. The station will automatically perform a variety of operations without user intervention.

Sperian Protection Instrumentation and Honeywell

Sperian Protection Instrumentation is a global leader in personal safety equipment. The company was recently acquired by Honeywell, another global leader in technology and innovation. As a Fortune 100 company, Honeywell has a vested interest in maintaining its reputation as a developer of efficient and reliable safety equipment. Sperian Protection Instrumentation helps to expand Honeywell s personal safety offerings while advancing their position in the American market. By purchasing a product by Sperian and Honeywell, customers can be assured they are receiving the very best in safety technology and equipment.

XNX-AMAV-FHIF1 XNX Universal Transmitter, ATEX M25 AL FF HRT MPD IR LEL by Honeywell Analytics

XNX Universal Transmitter, ATEX M25 AL FF HRT FOR TOX/O2 SNSRThe XNX Universal Transmitter, now with HART EDDL, marks a new turn in gas detection from Honeywell Analytics. It supports the widest range of sensors on a common platform and offers a modular choice of inputs and outputs.

XNX is designed for flexible integration, simple installation, user-friendly operation and straight-forward maintenance. It is ideal for use with a range of gas monitoring controllers or industry standard PLCs. The introduction of our HART Enhanced Device Descriptor Language (EDDL) software provides users with an at-a-glance indication of the health of their gas detectors in the field.

Bringing together the best solutions in gas detection

Electrochemical

• Proven electrochemical sensing technology
• Surecell™ electrochemical cells are ideal for hot and humid environments
• Long life sensing cells (typical >2 years)
• Patented 'Reflex' sensing element verification diagnostics
• Sensor recognition software auto configures transmitter
• Plug and play factory configured sensors
• Intrinsically safe sensor connection permits hot swap, reducing down time

Catalytic Bead

• Supports Honeywell Analytics 705, 705HT, Sensepoint, Sensepoint HT and MPD sensors
• Fast response to wide range of hydrocarbons and flammables

Infrared (Open Path IR, Point IR, IR Cell)

• Supports Honeywell Analytics Searchline Excel, Searchpoint Optima Plus
• Failsafe operation
• Fast speed of response
• Reduced routine maintenance
• Immune to catalytic poisons
• Long operating life
• Works in inert atmospheres

High performance

• Flammable gas detection 0 to 100% LFL/LEL
• Point IR with heated optics provides immunity to poisoning and no hidden faults
• Open-path IR flammable gas detection in LEL-m measurement
• Electrochemical cell offers toxic gas detection in ppm
• IR cell provides CO₂ and combustible gas monitoring
• Robust and reliable operation in explosive areas and harsh environments

Flexible Operation

• 3 versions - supports (Catalytic Bead and IR Cell), Electrochemical Cell and IR (point and open-path) gas detection
• Multi-Purpose Detector (MPD) with field serviceable mV, Catalytic bead and IR Cell capability
• 4-20mA with HART® as standard
• HART Enhanced Device Description Language (EDDL) software*
• Multiple communications options include up to 3 relays, MODBUS® and FOUNDATION® H1 Fieldbus
• Optional local IS port for handheld HART configurator

Easy to Use

• Large, backlit, easy-to-view LCD display offers multisensory indicators (visual icons, colored buttons, text, etc.) to display gas and sensor readings
• User interface supported by 8 selectable languages (English, Spanish, German, Italian, Portuguese, French, Russian, Chinese)
• Self-test and fault indication features
• Non-intrusive, one-man operation
• Quick calibration with auto-inhibit

Easy to Install

• 3 or 4 wire operation, source, sink or isolated
• Simple plug-in sensors and replaceable cells
• NEMA 4X IP66 rated for rugged indoor/outdoor use
• Five conduit entries for ease of installation

Cost Effective

• Minimal training required
• One-man operation
• Plug-in sensor replacement
• All necessary accessories included

XNX-UTAV-MNIF1 XNX Universal Transmitter, UL 3/4 AL MDBS MPD IR LEL by Honeywell Analytics

XNX Universal Transmitter, ATEX M25 AL FF HRT FOR TOX/O2 SNSRThe XNX Universal Transmitter, now with HART EDDL, marks a new turn in gas detection from Honeywell Analytics. It supports the widest range of sensors on a common platform and offers a modular choice of inputs and outputs.

XNX is designed for flexible integration, simple installation, user-friendly operation and straight-forward maintenance. It is ideal for use with a range of gas monitoring controllers or industry standard PLCs. The introduction of our HART Enhanced Device Descriptor Language (EDDL) software provides users with an at-a-glance indication of the health of their gas detectors in the field.

Bringing together the best solutions in gas detection

Electrochemical

• Proven electrochemical sensing technology
• Surecell™ electrochemical cells are ideal for hot and humid environments
• Long life sensing cells (typical >2 years)
• Patented 'Reflex' sensing element verification diagnostics
• Sensor recognition software auto configures transmitter
• Plug and play factory configured sensors
• Intrinsically safe sensor connection permits hot swap, reducing down time

Catalytic Bead

• Supports Honeywell Analytics 705, 705HT, Sensepoint, Sensepoint HT and MPD sensors
• Fast response to wide range of hydrocarbons and flammables

Infrared (Open Path IR, Point IR, IR Cell)

• Supports Honeywell Analytics Searchline Excel, Searchpoint Optima Plus
• Failsafe operation
• Fast speed of response
• Reduced routine maintenance
• Immune to catalytic poisons
• Long operating life
• Works in inert atmospheres

High performance

• Flammable gas detection 0 to 100% LFL/LEL
• Point IR with heated optics provides immunity to poisoning and no hidden faults
• Open-path IR flammable gas detection in LEL-m measurement
• Electrochemical cell offers toxic gas detection in ppm
• IR cell provides CO₂ and combustible gas monitoring
• Robust and reliable operation in explosive areas and harsh environments

Flexible Operation

• 3 versions - supports (Catalytic Bead and IR Cell), Electrochemical Cell and IR (point and open-path) gas detection
• Multi-Purpose Detector (MPD) with field serviceable mV, Catalytic bead and IR Cell capability
• 4-20mA with HART® as standard
• HART Enhanced Device Description Language (EDDL) software*
• Multiple communications options include up to 3 relays, MODBUS® and FOUNDATION® H1 Fieldbus
• Optional local IS port for handheld HART configurator

Easy to Use

• Large, backlit, easy-to-view LCD display offers multisensory indicators (visual icons, colored buttons, text, etc.) to display gas and sensor readings
• User interface supported by 8 selectable languages (English, Spanish, German, Italian, Portuguese, French, Russian, Chinese)
• Self-test and fault indication features
• Non-intrusive, one-man operation
• Quick calibration with auto-inhibit

Easy to Install

• 3 or 4 wire operation, source, sink or isolated
• Simple plug-in sensors and replaceable cells
• NEMA 4X IP66 rated for rugged indoor/outdoor use
• Five conduit entries for ease of installation

Cost Effective

• Minimal training required
• One-man operation
• Plug-in sensor replacement
• All necessary accessories included

72-5120RK Eagle Portable Monitor for Methane (CH4) (100% LEL/100% Vol (IR), Autoranging) by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

72-5115RK-XX Eagle Portable Monitor for Carbon Dioxide (CO2) (Specify CO2 Range) by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

2811-4501-001M EC 28 Gas Transmitter with MODBUS, Ammonia (NH3), 0-100 ppm, No Display by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

M5-XU0Y-R-P-D-B-N-00 GasAlertMicro 5 Detector % LEL (Unfiltered), O2, H2S, CO - Rechargeable Battery and Pump - Black Housing by BW Technologies

The GasAlertMicro 5 Series is the most customizable gas monitoring series on the market. With an extensive selection of models, user options, and instrument settings, this multi-gas detector series is an industry leader. BW Technologies by Honeywell recognizes that not all worksites can operate with a one size fits all model of gas detection devices. With the introduction of the GasAlertMicro 5 Series multi-gas detectors, worksites, managers, and users can utilize the customizable features to ensure that the instrument meets their specific worksite needs.

GasAlertMicro 5 Series models

This multi-gas monitor series is available in several models: the standard toxic gas model, a PID model for detection of VOCs, or an IR model for CO2 detection. The unit accurately and reliably identifies up to five atmospheric hazards simultaneously and can rapidly switch from diffusion mode to the optional integrated pump.

Each model of GasAlertMicro 5 Series has several distinct features. With the GasAlertMicro 5 Series, the standard toxic gas model, users can monitor several standard gases with a plug in electrochemical cell sensor and catalytic cell sensor and a typical battery life of 20 hours (AA Alkaline rechargeable). The GasAlertMicro 5 PID is standard with several gas detections, a plug in electrochemical cell sensor and photoionization detector, and a battery life of approximately 15 hours (AA Alkaline rechargeable). Finally, the GasAlertMicro 5 IR features specific gas detection ranges, a plug in electrochemical cell sensor, a catalytic cell sensor, and an infrared sensor for carbon dioxide monitoring. This model also has a battery life of approximately 15 and AA Alkaline rechargeable batteries. For more information about available sensor configurations, please contact BW Technologies by Honeywell.

Exclusive features

Each GasAlertMicro 5 Series device features several exclusive features including a triple alarm system, raised glove-friendly buttons, a large easy to read display, stainless steel alligator clip, visual filter inspection, and automatic activation tests. When the unit is activated, the gas detector will automatically test for sensor integrity, circuitry, and battery. This continuous and reliable testing process ensures that the integrity and dependability of the device is never a concern.

BW Technologies by Honeywell also recognizes the unique needs of the various industries with environmental hazards. With each industry anticipating a separate set of possible dangers, the ability to customize safety devices is critical.

Users and worksite managers will be comforted to know their GasAlertMicro 5 series model is fully customizable. Customizable features include STEL intervals, TWA methods, sensor activation, alarms, display settings, record keeping, pumps, combustible gas measurements, start up calibration, backlights, activation modes, calibration levels, daily bump tests, and languages. To protect the integrity of the user settings and the safety of the gas monitoring device, the GasAlertMicro 5 device features a passcode function to prevent unauthorized manipulation of settings.

Accessories

The GasAlertMicro 5 Series is also compatible with BW's MicroDock II automatic test and calibration system. Users may purchase additional accessories to help fully tailor the gas detection unit to their needs. Accessories include an integral pump and battery charger, a confined space kit, a belt holster, and a collapsible sampling probe.

Part Number: M5-XU0Y-R-P-D-B-N-00

725-004-05 Eagle 2 Portable Monitor for LEL & PPM/O2/H2S/CO/CO2 60% Volume (IR) by RKI Instruments

Continuing in its legacy of durable and reliable gas detection and monitoring systems, RKI Instruments is proud to offer a new product in its popular Eagle portable gas detector series. The Eagle 2 can monitor up to 6 different gases and is equipped with several exclusive features that can only be found with the Eagle series. In addition, its large glove friendly push buttons and LCD screen ensure an ease of use when onsite. Rated intrinsically safe, the Eagle 2 is equipped with state of the art technologies that are not available with other competitive gas detectors and monitors.

Specialty Sensors

The Eagle 2 has a variety of available specialty sensors. Workers can use a photoionization detector for low or high range VOC detection and Fence Electrode Technology for humidity and contamination resistance. An infrared sensor is available for Co2, % LEL CH4, % Volume CH4, % LEL HC, and % Volume HC. Thermal conductivity sensors are available for % Volume H2 and % Volume CH4. The unit is also compatible with the smart plug and play toxic sensors for the detection of NH3, AsH3, CI2, HCN, PH3, and SO2. With the wide variety of sensors and gas detection available, the Eagle 2 can be customized to meet almost all worksite gas detection needs.

Exclusive Features

The monitor has a long internal pump that can draw samples for up to 125 feet. The pump features a low flow auto shut off and alarm. This allows operators to respond swiftly from a safe distance. The unit is multilingual with 5 different language preferences, and features an alkaline battery life of 18 hours or a NiMH life of 20 hours. To protect the integrity of the device and the configurations, the unit can be password protected. The Eagle 2 also has standard data logging capabilities for easy research, evaluation, and site monitoring. To reduce calibration costs and time, the unit features an automatic calibration option and a single gas calibration option.

The Eagle 2 is heavily protected from environmental conditions by a weather proof, chemical resistant RFI/EMI coated high impact polycarbonate/PBT blend enclosure. The enclosure also renders the unit water and dust resistant. Because of the enclosure, the Eagle 2 can function in 2 inches of water without leakage.

Eagle 2 Specifications

The portable and durable unit is lightweight at less than 4 pounds. Its dimensions are suitable for convenient carrying (9.5?L x 5.25?W x 5.875?H), and it features a conveniently placed durable top handle. The large easy to read display has a polyurethane overlay backlights on demand and when the alarm is activated. The 2 alarm channels are fully adjustable for the user and can be password protected. With a 95 dB buzzer and 4 high intensity LEDs, the alarm is sure not to be missed. The Eagle 2 is standard with a 2 year warranty for material and workmanship and a 1 year warranty for PID sensor.

*Please note we can only ship RKI products to customers within the United States

TPPLBAWV4NNNNNN Touchpoint Plus Basic Wall Mount Controller, AC115/220 150W, 4 x mV input by Honeywell Analytics

Touchpoint Plus brings a whole new control experience to your small system of gas detectors. Touchpoint Plus is an easily configurable, wall mounted control system that supports up to sixteen channels of gas detection. Its modular approach enables you to take control and configure what you need for a wide range of applications.

The signature feature of the Touchpoint line is a user-friendly touchscreen interface, and the Touchpoint Plus takes it to a new level. With this unique interface, it's easier than ever to see the status of your system at a glance - maximizing the time you have to make the right decisions. The intuitive, multilingual interface, simplifies operation and reduces training requirements. The full colour traffic light style status indication provides clarity from a distance too.

Touchpoint Plus includes a comprehensive set of outputs as standard including common alarms and dedicated drives for remote audiovisual indicators. Its modularity enables you to customise your system to meet your specific application requirements. Selecting the right detector for use with your controller can deliver significant savings in startup costs and on-going operations. Our global partner network and dedicated application specialists are able to help make the right choices for your industry.

With everything at your fingertips, you can take ownership of your system and operate it with confidence, ensuring the safety of your people and productivity of your site.

Delivering reliable control

• Honeywell reliability from the most trusted experts in gas detection
• Built-in battery backup for constant uptime
• Robust, shockproof housing for a wide range of industrial environments

Flexible capabilities

• Compatible with the full range of Honeywell gas detectors
• Powered audiovisual alarms simplify field installation
• Configuration includes easy grouping and voting alarm logic without specialist knowledge
• Next-generation compatibility
• Optional Modbus output for integration with a higher level system

Providing ease and efficiency

• Quick and easy installation, configuration, commissioning and maintenance
• Easy diagnostics, data and reporting
• Minimised training time
• Large colour touchscreen LCD
• Multilingual capabilities
• Green-yellow-red status at a glance

G999P-03-03-00-00-00-61-20K G999 Multi-gas Atmospheric Monitor Value Kit, 5 year O2 (lead free), 3 year COSH, IR LEL includes calibration cap, cable, charging cradle and wall power adapter by GfG

The Microtector III G999 combines the demands of a modern multi-gas measurement device for protecting workers with the ability to safely measure confined spaces. As a robust and sophisticated multi-gas detector, it is versatile in its application and flexible in sensor combinations.

Advantages

Safety through quality and functionality

To fit every environment, there are three versions available. All versions include three electrochemical and one infrared sensor. Depending on the version, the G999 features a catalytic combustion (CC) sensor, a combined CC/semiconductor sensor, a PID sensor or a fourth electrochemical sensor. This allows a variety of gas combinations or measuring ranges to be defined and simultaneously monitored.

The well thought-out design of the housing and the menu navigation, allows for easy operation in difficult situations. For example, the display can be easily rotated 180°, so that it is always easy to read. For work in poorly lit rooms or in emergency situations, the G999 features an explosion-proof LED torch.

Designed for difficult working conditions

The Microtector III G999 is certified for use in Ex Zone 0 and is water and dust-proof according to protection class IP 67 and is suitable for challenging applications. The rubberized polycarbonate housing provides excellent protection against jolts and impacts, while the practical design and robust crocodile clip ensure optimum wearing comfort.

Ample Battery Power for Long Operating Times

Unlike other devices, the G999 features a double battery capacity of up to 130 hours of operation and provides power supply to the pump.

Remote Monitoring to Protect Employees

If devices with radio modules are used, teams can be monitored centrally via the portable GfG-Link or using a computer and USB dongle. Information regarding the measured gas concentrations, alarms and the status of the man-down alarm will then be available in real time.

Prepared for an Emergency - Alarm for Exercise

In the event of an alarm, knowing how to behave is highly important. By means of the alarm simulation any gas values can be transmitted to the Microtector III G999 to simulate and train different emergency scenarios.

Maintenance & Documentation – Location-Independent and Legally Compliant

The test and docking stations for the Microtector III G999 not only allow location-independent, daily display tests and regular functional checks, but also the complete documentation.

G888 – The Perfect Match

It is not always necessary to equip every employee with a gas detector including a pump for safe measurement of confined spaces, but everyone should have a modern multi-gas detector. In such situations the Microtector III G888 is recommended. Like the G999, it offers optimum individual protection for all those who have to work in hazardous areas and/or enclosed spaces.

XNX-AMSE-MHNNN XNX Universal Transmitter, ATEX M25 SS MDBS HRT FOR TOXO2 SNSR by Honeywell Analytics

XNX Universal Transmitter, ATEX M25 AL FF HRT FOR TOX/O2 SNSRThe XNX Universal Transmitter, now with HART EDDL, marks a new turn in gas detection from Honeywell Analytics. It supports the widest range of sensors on a common platform and offers a modular choice of inputs and outputs.

XNX is designed for flexible integration, simple installation, user-friendly operation and straight-forward maintenance. It is ideal for use with a range of gas monitoring controllers or industry standard PLCs. The introduction of our HART Enhanced Device Descriptor Language (EDDL) software provides users with an at-a-glance indication of the health of their gas detectors in the field.

Bringing together the best solutions in gas detection

Electrochemical

• Proven electrochemical sensing technology
• Surecell™ electrochemical cells are ideal for hot and humid environments
• Long life sensing cells (typical >2 years)
• Patented 'Reflex' sensing element verification diagnostics
• Sensor recognition software auto configures transmitter
• Plug and play factory configured sensors
• Intrinsically safe sensor connection permits hot swap, reducing down time

Catalytic Bead

• Supports Honeywell Analytics 705, 705HT, Sensepoint, Sensepoint HT and MPD sensors
• Fast response to wide range of hydrocarbons and flammables

Infrared (Open Path IR, Point IR, IR Cell)

• Supports Honeywell Analytics Searchline Excel, Searchpoint Optima Plus
• Failsafe operation
• Fast speed of response
• Reduced routine maintenance
• Immune to catalytic poisons
• Long operating life
• Works in inert atmospheres

High performance

• Flammable gas detection 0 to 100% LFL/LEL
• Point IR with heated optics provides immunity to poisoning and no hidden faults
• Open-path IR flammable gas detection in LEL-m measurement
• Electrochemical cell offers toxic gas detection in ppm
• IR cell provides CO₂ and combustible gas monitoring
• Robust and reliable operation in explosive areas and harsh environments

Flexible Operation

• 3 versions - supports (Catalytic Bead and IR Cell), Electrochemical Cell and IR (point and open-path) gas detection
• Multi-Purpose Detector (MPD) with field serviceable mV, Catalytic bead and IR Cell capability
• 4-20mA with HART® as standard
• HART Enhanced Device Description Language (EDDL) software*
• Multiple communications options include up to 3 relays, MODBUS® and FOUNDATION® H1 Fieldbus
• Optional local IS port for handheld HART configurator

Easy to Use

• Large, backlit, easy-to-view LCD display offers multisensory indicators (visual icons, colored buttons, text, etc.) to display gas and sensor readings
• User interface supported by 8 selectable languages (English, Spanish, German, Italian, Portuguese, French, Russian, Chinese)
• Self-test and fault indication features
• Non-intrusive, one-man operation
• Quick calibration with auto-inhibit

Easy to Install

• 3 or 4 wire operation, source, sink or isolated
• Simple plug-in sensors and replaceable cells
• NEMA 4X IP66 rated for rugged indoor/outdoor use
• Five conduit entries for ease of installation

Cost Effective

• Minimal training required
• One-man operation
• Plug-in sensor replacement
• All necessary accessories included

5600-3112 GDX-350 Gas Sensor Transmitter/Monitor, [H2] 0-1000 ppm, 3-wire - with Relays and Modbus by Bacharach

Bacharach's new state-of-the-art GDX-350 transmitters, with Smart Sensor technology, provide accurate and continuous detection of toxic, combustible and asphyxiate gases. The full-featured design of the GDX-350 includes a large LCD display, a 4-20 mA interface, programmable alarms, optional relays and a Modbus interface. Exclusive pre-calibrated replacement sensor technology makes occasional maintenance practically effortless. Rugged construction, intrinsic safety capability (in two-wire mode with barrier) and an explosion-proof housing allow the GDX-350 to operate directly in hazardous-rated areas of many industrial environments, delivering reliable, superior-sensing performance to protect human life, equipment and property.

With its large LCD display, the GDX-350 shows gas concentrations, engineering units and bar graphs along with the most recent 30 minutes of trend data. Utilizing the on-board magnetic keypad, users can also navigate through the display to change alarm set points, instrument configurations, or enter into maintenance mode for non-intrusive sensor calibration. For security, menu options also enable the selection of an authorization code to lock critical parameters. Accompanying the LCD display are standard LED alarm indicators that show when low and high alarm conditions are met. An optional relay board is available to provide three 5-amp relays that can be used to drive audible/visual alarms, or activate exhaust fans.

Features & Benefits:

• Pre-calibrated Smart Sensor capability with 'plug-n-play' convenience minimizes maintenance and downtime
• Non-Dispersive Infrared (NDIR), Catalytic Bead and Electrochemical sensor options available
• Can be placed directly in hazardous environments where leaks occur for quick detection and rapid response
• Graphic LCD for real-time monitoring of concentrations
• 4-20 mA, optional Modbus RTU® and wireless interface
• Easily update alarm set points, configurations or maintenance modes using the LCD display
• 30-minute onboard data trend

72-5222RK-04 Eagle Portable Monitor for O2/CO2 (0 - 20%) by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

8025-4021 RAM 4021 Respiratory Air Monitor with Wall Mount Filter Panel / 25 CFM with 4021 (2 ports) by GfG

The RAM 4021 AutoCal® series is the unit of choice where specific and accurate measurement of carbon monoxide, oxygen or dew-point levels are required. Designed to meet OSHA requirements for monitoring of Grade D respirable air, this unit is equipped with a reliable electrochemical sensor that accurately indicates the level of carbon monoxide on an illuminated liquid crystal display. Adding versatility, this unit offers optional oxygen or dew point sensors for applications where detection or measurement is needed.

Calibration and maintenance are simple with our innovative AutoCal® system. Additional features including alarm relay contacts, user adjustable alarm point, low flow alarm indicator and many more make this unit an intelligent choice. The RAM 4021 is available in four models, the 4021 (CO), 4021-1 (CO and O2), 4021-DPX (CO and dew point levels) and 4021-PR (CO and additional relay to signal power loss to monitor, complies with newest NFPA regulation). All models may be purchased with or without airline filter systems

Respiratory air specifications

All GfG Instrumentation RAM Instruments satisfy the requirements of OSHA rule 29 CFR 1910.134 (d) (2) (ii) for carbon monoxide monitoring. They will also monitor Grade E air, generally specified for breathing air in cylinders (SCBA).

Wall mounted filter panel option

The 25, 50 and 100 CFM panels filter out dangerous toxins from supplied air sources and ensure clean, breathable air. The threestage filter system efficiently removes particulates, oil vapors and hydrocarbons from an air supply. After filtration, the regulator sets the pressure for the respiratory equipment and the manifold assembly provides multiple outlets for airline hose quick connections. The model 8025 panel includes two user female quick connect outlets; the 8050 includes four, and the 8100 includes eight. A 1/2" FPT connection is standard on all 50 and 100 CFM panels, and a 3/8" FPT connection is standard on all 25 CFM panels.

Features

• Continuous compressed air CO monitor
• Integrated dew point measurement
• Robust easy-to-operate design

Features

• RAM 4021 Monitor
• Carbon monoxide (CO) sensor
• Other sensors (as specified)
• Manual