$2000 - $4000

2813-712-001 EC 28i Intrinsically Safe Transmitter with Sensor, Chlorine Dioxide (ClO2), No Display by GfG

Features

• Full-featured smart transmitter for oxygen or a wide range of toxic gas measurement
• Non-intrusive AutoCal calibration adjustment
• Increased safety design to reduce installation cost in potentially hazardous locations
• Intrinsically safe (i) EX-Proof version
• BVS 04 ATEX E 132 X (electrical ex-protection) II 1G EEx ia IIC T4 C 0158
• Available in two configurations: Blind (no display), Display
• Barriers are required
• EX- conduit is not required
• Reduced installation costs

2811-4042-003M EC 28 Gas Transmitter with MODBUS, Ammonia (NH3), 0-200 ppm for Flash Freezers, Display / Alarm by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

72-6ABP-A GX-6000 One Sensor Sample Draw Gas Monitor, LEL/Oxy/H2S/CO/VOC(0-6K ppm 10.6 eV)/Cl2(0-10 ppm), with alkaline battery pack by RKI Instruments

Simply put, the GX-6000 is a game changer. This powerful hand-held instrument is capable of simultaneously monitoring up to 6 gases. In addition to the standard 4 confined space gases which include combustibles, O2, CO, & H2S, the GX-6000 has 2 additional smart channels that accept PID, IR or super toxic sensors. Equipped with a strong internal sample pump, a man-down alarm, a panic alarm, an LED flashlight, and large auto rotating LCD display, the GX-6000 can operate as a single gas PID unit or a multifunctional tool utilizing all 6 channels. The GX-6000 with a PID sensor will come equipped with a library of over 600 VOC gases to choose from as standard. Choosing from the library is easy with a personalized favorites list of 30 commonly used VOC's as well as a list of 8 of the most recently used VOC's.

The GX-6000 has a rugged design built for the nastiest environments. It is equipped with a removable impact-resistant rubber boot and a dust and water resistant enclosure with an IP-67 rating. With 5 bright LED lights on 3 sides of the instrument, alarms are easily seen from a variety of perspectives. With vibration and loud audible alarm, GX-6000 will easily alert users when needed.

Features

• Monitor up to 6 gases
• 2 smart sensor slots auto recognize PID, IR, and super toxic sensors
• 5 Operating modes: normal, leak check, inert, snap log and bar hole
• Library of over 600 VOCs
• PPM Leak Check mode
• Man-down and panic alarms
• Auto display rotation
• LED Light source
• Internal sample pump
• Glove friendly glow in the dark buttons
• Light weight, small, rugged IP-67 design
• Interchangeable battery packs Li-ion / alkaline
• Operates up to 14 hours on Li-ion battery pack, fully recharges in 3 hours
• Field replaceable sensors, batteries and filters

Applications

• Confined space entry
• Hazmat response teams
• Arson investigation
• Remediation sites
• Perimeter monitoring
• Leak detection
• Landfill monitoring
• Wing tank entry

*Please note we can only ship RKI products to customers within the United States

F04-J111-110 Meshguard Steel EchoView, 2.4 GHz by RAE Systems

The RAE Systems by Honeywell EchoView is a portable, intrinsically safe (Class I, Division 1 and Zone 0) alarm notification device that allows you to monitor your sensor network remotely. It displays the sensor readings of up to 16 MeshGuard Monitors on a wireless network and retrieves all monitor information that is typically viewed on the system controller.

• Class I, Division 1 (Zone 0) certified
• Customs Union: 0Ex ia IIC T4 Ga/PO Ex ia I Ma
• Allows users to be away from the controller and still be notified of alarm conditions
• The EchoView gets all sensor readings directly from the controller
• 10+ days run time with internal battery, 45+ days run-time with external PowerPak

D01-S00G-011 MeshGuard Stainless Steel Detector, Flammables by RAE Systems

The RAE Systems by Honeywell MeshGuard gas detection monitor is a key building block of the MeshGuard intelligent network of connected sensors for gas detection in industrial safety and oil and gas applications.

The MeshGuard system is designed for quick deployment in areas where low cost/high ROI solutions are required. MeshGuard is available with field-replaceable precision sensors specifically designed to sense toxic and flammable gases.

Key Features

• Stainless Steel housing
• Self-forming wireless network; units come online automatically
• Compact and lightweight
• IP-65 rated weather resistant, and splash guard equipped for sensor protection
• Multiple controller options for realtime wireless data collection and viewing
• Self-healing network automatically routes data back to controller through best wireless path available
• Battery powered operation for up to 6 months
• SolarPak provides 24/7 uptime
• Intrinsically Safe
• Magnetic mounting option for quick and easy MeshGuard installation

Applications

• Oil and gas drilling operations
• Oil and gas production
• Plant maintenance turnarounds
• Industrial safety
• Tank farms
• Shipyards and maritime
• Fast deployment and decommissioning time
• Simple to install and operate
• Rugged and reliable
• Versatile to accommodate many applications

MeshGuard Detector Includes:

• MeshGuard detector with sensor as specified
• Operation and maintenance manual
• Calibration gas test adapter
• Enhanced-capacity Lithium battery installed
• Maintenance tool

4021-TS-H RAM 4021 Respiratory Air Monitor with Toggle Switch, Carbon Monoxide (CO), Low H2 Interference CO Sensor by GfG

The RAM 4021 AutoCal® series is the unit of choice where specific and accurate measurement of carbon monoxide, oxygen or dew-point levels are required. Designed to meet OSHA requirements for monitoring of Grade D respirable air, this unit is equipped with a reliable electrochemical sensor that accurately indicates the level of carbon monoxide on an illuminated liquid crystal display. Adding versatility, this unit offers optional oxygen or dew point sensors for applications where detection or measurement is needed.

Calibration and maintenance are simple with our innovative AutoCal® system. Additional features including alarm relay contacts, user adjustable alarm point, low flow alarm indicator and many more make this unit an intelligent choice. The RAM 4021 is available in four models, the 4021 (CO), 4021-1 (CO and O2), 4021-DPX (CO and dew point levels) and 4021-PR (CO and additional relay to signal power loss to monitor, complies with newest NFPA regulation). All models may be purchased with or without airline filter systems

Respiratory air specifications

All GfG Instrumentation RAM Instruments satisfy the requirements of OSHA rule 29 CFR 1910.134 (d) (2) (ii) for carbon monoxide monitoring. They will also monitor Grade E air, generally specified for breathing air in cylinders (SCBA).

Wall mounted filter panel option

The 25, 50 and 100 CFM panels filter out dangerous toxins from supplied air sources and ensure clean, breathable air. The threestage filter system efficiently removes particulates, oil vapors and hydrocarbons from an air supply. After filtration, the regulator sets the pressure for the respiratory equipment and the manifold assembly provides multiple outlets for airline hose quick connections. The model 8025 panel includes two user female quick connect outlets; the 8050 includes four, and the 8100 includes eight. A 1/2" FPT connection is standard on all 50 and 100 CFM panels, and a 3/8" FPT connection is standard on all 25 CFM panels.

Features

• Continuous compressed air CO monitor
• Integrated dew point measurement
• Robust easy-to-operate design

Features

• RAM 4021 Monitor
• Carbon monoxide (CO) sensor
• Other sensors (as specified)
• Manual

72-2104RK-02 Beacon 410 Four Channel Wall Mount Controller with Strobe Light (No Sensor) by RKI Instruments

RKI Instruments is dedicated to producing the most reliable gas detection and monitoring systems on the market. With a reputation for excellence, RKI consistently produces the most effective gas detection and monitoring systems ensuring safe working conditions.

RKI Instruments understands that many workplace settings implement a gas detection system and mechanism as a standard protocol. Worksites such as petrochemical plants, refineries, water and wastewater treatment plants, mills, parking garages, and manufacturing facilities need constant monitoring for potential life threatening atmospheric hazards. In these settings, workplace safety managers need a dependable and reliable gas detection system for constant and daily use. With the introduction of RKI Instruments' Beacon 410 Four Channel Wall Mount Controller, safety managers can feel confident and secure that their jobsite is being monitored appropriately and effectively.

The Beacon 410 Four Channel Wall Mount Controller

The Beacon 410 is a customizable, microprocessor based 4 channel gas monitor. The unit simultaneously monitors up to 4 channels with a digital display reading all 4 channel readouts simultaneously. The unit is compatible with the easy to use direct connect sensors for LEL, CO2, 02, and toxic gases. The unit can also monitor any 4-20mA transmitter.

Each channel has 3 fully configurable alarm points. Within each channel, there are 2 dedicated fully configurable relays and a bank of common relays which can be configured as additional channel relays allowing up to 3 alarm relays per channel. Furthermore, a 4-20mA output signal is provided by each channel.

Ease of Use

The wall mount features an easy to read 4 x 20 backlit alphanumeric LCD display which simultaneously reads the gas levels for the 4 gases. Additionally, the Calibration Mode allows for easy calibration while in the field. The control panel allows for an easy understanding of how to adjust configurations. With a maximum of 6 switches or keys (including an alarm reset switch), users can easily configure the unit for maximum customization.

For worksite safety managers that need to evaluate and monitor collective data, each Beacon 410 is equipped with a digital Modbus interface for remote logging through a Modbus network. Additionally, the unit features minimum and maximum range data that can be viewed at any time.

Beacon 410 Specifications

The Beacon 410 wall mount efficiently fits onto a wall with convenient dimensions of 12.5"H x 11"W x 6.4"D. For safe monitoring, the unit features a dual alarm system with a 94 dB audible alert that is mounted on the enclosure and a visual color coded LED alert system. The technology is encased in a durable NEMA 4x non-metallic enclosure that is appropriate for indoor and outdoor locations. It is both chemical resistant and weather resistant. The wall unit is powered by 115 VAC and 220 VAC. An optional battery backup option is available.

Each unit is available with a standard 1 year warranty for materials and workmanship.

*Please note we can only ship RKI products to customers within the United States

AAA104106 SP-MGTP Portable Multi Gas Detector, O2, CO, H2S, CH4 (IR), CO2 (IR) H2 by Senko

SP-MGTP is a sampling-type multi-gas detector capable of monitoring up to 6 gases with 37 possible gas combinations, including Volatile Organic Compounds (VOC). It continuously detects oxygen (O2), toxic, flammable gases, and VOCs, providing real-time alerts through LED indicators, sound alarms, and vibration signals. Designed to prevent industrial accidents caused by hazardous gas exposure, this device offers reliable protection in demanding environments.

KEY FEATURES

• Sampling-type with embedded pump & probe
• Max 6 gases with 37 different gas combinations
• Event log (Recent 30 event / bump / calibration)
• Easy to maintain (2 filters in probe & in detector)
• Inner teflon coating of gas tube line

0555 6744 Dew Point Transmitter (with display; 1/2 NPT) by Testo

The testo 6740 was especilally developed for trace humidity measurement in compressed or dry air (e. g. granulate dryers). Thanks to a special adjustment, optimum accuracy in the trace humidity range has been achieved. The result of the development of the testo 6740 is a measuring range of -45 °C_td to +30 °C_td and excellent accuracy.

For the display of the relevant trace humidity parameters, a freely scalable analog output is available, optionally with a switch contact plug for MAX monitoring. In addition to this, the testo 6740 stands out thanks to its compact and userfriendly design, such as the rotatability of the housing by 350° for the optimum positioning of the display.

• Measurement of dewpoints in the range from -45 °C_td to +30 °C
• Testo polymer humidity sensor with high accuracy and longterm stability
• Convenient operation via the display menu
• Analog output 4 to 20 mA (2-wire) and optional alarm plug with 2 integrated switch outputs
• Compact design with rotatable housing by 350° for optimum positioning of display
• Display with operating menu (optional)
• Trace humidity adjustment without reference measuring instrument possible on site with accessory (2-point adjustment device)

VFD 20HP 380/480V 3 Phase IP66 / NEMA 4X Indoor/Outdoor

2813-709-001 EC 28i Intrinsically Safe Transmitter with Sensor, Chlorine (Cl2), No Display by GfG

Features

• Full-featured smart transmitter for oxygen or a wide range of toxic gas measurement
• Non-intrusive AutoCal calibration adjustment
• Increased safety design to reduce installation cost in potentially hazardous locations
• Intrinsically safe (i) EX-Proof version
• BVS 04 ATEX E 132 X (electrical ex-protection) II 1G EEx ia IIC T4 C 0158
• Available in two configurations: Blind (no display), Display
• Barriers are required
• EX- conduit is not required
• Reduced installation costs

72-5109RK Eagle Portable Monitor for Ozone (O3) (No Probe), 0 - 1 PPM by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

Novo 1-P 2-Gas Novo Pro Kit (BUILT-IN Printer): O2, CO, CO2, Combustion Efficiency, Excess Air, Draft, Pressure, Temperature, Calculations for High Efficiency & Condensing Systems, 12" Probe with 6' Hose, Hard Plastic Carrying Case, & Real-Time Bluetooth® Apps (iOS and Android) by Seitron Americas

• 7" Touch Screen for easy menu navigation
• Simultaneous Gas Pressure + Combustion Measurements
• Optional Built-in Printer
• Long Life O2 Sensor (4 Years)
• New Dual Range (Low/High) Sensor Technology
• Low NOx and SOx sensors
• 15 Preprogrammed Fuels
• Including Natural Gas, Oil, Propane, & Biofuels
• CO Protection Dilution Pump
• Rechargeable Li-Ion Batteries
• Integrated water trap with LED backlight for easy maintenance
• Differential Pressure Manometer
• Draft Measurement
• Mobile App for iOS and Android

Every Kit Includes

• Combustion Analyzer
• Gas probe with 12" (300 mm) interchangeable tip
• 10 ft (3m) Single Connection Hose
• Integrated water trap
• Manometer Hoses
• Outdoor Combustion Air Temp Probe
• AC Power Adapter & Cable
• Hard plastic kit case
• Quick Guide
• Calibration Certificate

Main Features

• Precalibrated Gas Sensors
• Field Replaceable
• Altitude Adjustment
• Integrated magnets
• Automatic autozero (with gas sampling probe inserted in the chimney)
• Self-diagnosis with verification of the functions and status of the sensors
• Language selectable by User
• 100,000 test memory
• Dimensions: Analyzer 10.6x3.6x2.7in (270x93x68mm), weight 2 lbs (0.9Kg) - Kit 5x18x13in (125x465x335mm), weight 11 lbs (5Kg)

Measured Values

• Differential Flue Gas and Ambient Air Temperatures
• Incoming Air Temperature and Ambient Air Temperature
• Draft and Differential Pressure
• Ambient CO
• O2 and CO in flue gas

Calculated Values

• Combustion Efficiency, including condensing units
• Stack losses and excess air
• Flow velocity with optional Pitot tube
• CO Air Free

2811-4501-004 EC 28 Gas Transmitter with Sensor, Ammonia (NH3), 0-100 ppm, Display / Alarm / Relay by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

Sperian Biosystems PhD6 Multigas Detector

The Biosystems PhD6 Multigas Detector is the latest development in compact multigas detection systems. The detector is proven to be compact, efficient, and cost effective. With dual alarm systems featuring ultra-loud audible indicators and ultra-bright LED visual indicators, users and those nearby are always notified when potential hazards may be present. When developing this detector, the engineers at SperianProtection Instrumentation also developed an express docking station that would reduce calibration time and labor costs. The detection and docking station help users meet record keeping requirements and reduce the risks of human error. With the SperianBiosystems PhD6 Multigas Detector, users can rest assured that they are receiving the very best in gas detection technology.

Key Features

The Biosystems PhD6 Multigas Detector is compatible with over 19 sensor choices including:

• PID
• IR-CO2
• IR-CH4
• Conventional LEL
• Oxygen
• 15 different toxic gas sensors

The gas detector is encased in a durable solid polycarbonate case with a rubber over mold for easy handling. It has an interchangeable battery pack with both Alkaline and Li-Ion rechargeable batteries. Both battery types offer up to 24 hour run times. The unit features dual audible alarms at 92 decibels and front and side ultra-bright LED visual alarms to ensure that the user and those nearby are always notified of possible hazardous conditions. For easy interpretation, the detector has an easy to read status bar and large LCD display that notifies users of the device s functionality and calibration due date. Using the menu options, users can easily adjust a variety of the instrument s settings.

Automatic Docking Station

When developing the PhD6 Multigas Detector, product developers also created an automatic docking station (Biosystems IQ6 Express Dock) to be fully compatible with the detector. The docking station aims to reduce labor time and costs by fully automating certain aspects of instrument maintenance including calibration, functionality testing, and record keeping. Using the Express Dock, users can maintain compliance with recordkeeping requirements by simply docking the detector in the station. The station will automatically perform a variety of operations without user intervention.

Sperian Protection Instrumentation and Honeywell

Sperian Protection Instrumentation is a global leader in personal safety equipment. The company was recently acquired by Honeywell, another global leader in technology and innovation. As a Fortune 100 company, Honeywell has a vested interest in maintaining its reputation as a developer of efficient and reliable safety equipment. Sperian Protection Instrumentation helps to expand Honeywell s personal safety offerings while advancing their position in the American market. By purchasing a product by Sperian and Honeywell, customers can be assured they are receiving the very best in safety technology and equipment.

Sperian Biosystems PhD6 Multigas Detector

The Biosystems PhD6 Multigas Detector is the latest development in compact multigas detection systems. The detector is proven to be compact, efficient, and cost effective. With dual alarm systems featuring ultra-loud audible indicators and ultra-bright LED visual indicators, users and those nearby are always notified when potential hazards may be present. When developing this detector, the engineers at SperianProtection Instrumentation also developed an express docking station that would reduce calibration time and labor costs. The detection and docking station help users meet record keeping requirements and reduce the risks of human error. With the SperianBiosystems PhD6 Multigas Detector, users can rest assured that they are receiving the very best in gas detection technology.

Key Features

The Biosystems PhD6 Multigas Detector is compatible with over 19 sensor choices including:

• PID
• IR-CO2
• IR-CH4
• Conventional LEL
• Oxygen
• 15 different toxic gas sensors

The gas detector is encased in a durable solid polycarbonate case with a rubber over mold for easy handling. It has an interchangeable battery pack with both Alkaline and Li-Ion rechargeable batteries. Both battery types offer up to 24 hour run times. The unit features dual audible alarms at 92 decibels and front and side ultra-bright LED visual alarms to ensure that the user and those nearby are always notified of possible hazardous conditions. For easy interpretation, the detector has an easy to read status bar and large LCD display that notifies users of the device s functionality and calibration due date. Using the menu options, users can easily adjust a variety of the instrument s settings.

Automatic Docking Station

When developing the PhD6 Multigas Detector, product developers also created an automatic docking station (Biosystems IQ6 Express Dock) to be fully compatible with the detector. The docking station aims to reduce labor time and costs by fully automating certain aspects of instrument maintenance including calibration, functionality testing, and record keeping. Using the Express Dock, users can maintain compliance with recordkeeping requirements by simply docking the detector in the station. The station will automatically perform a variety of operations without user intervention.

Sperian Protection Instrumentation and Honeywell

Sperian Protection Instrumentation is a global leader in personal safety equipment. The company was recently acquired by Honeywell, another global leader in technology and innovation. As a Fortune 100 company, Honeywell has a vested interest in maintaining its reputation as a developer of efficient and reliable safety equipment. Sperian Protection Instrumentation helps to expand Honeywell s personal safety offerings while advancing their position in the American market. By purchasing a product by Sperian and Honeywell, customers can be assured they are receiving the very best in safety technology and equipment.

Sperian Biosystems PhD6 Multigas Detector

The Biosystems PhD6 Multigas Detector is the latest development in compact multigas detection systems. The detector is proven to be compact, efficient, and cost effective. With dual alarm systems featuring ultra-loud audible indicators and ultra-bright LED visual indicators, users and those nearby are always notified when potential hazards may be present. When developing this detector, the engineers at SperianProtection Instrumentation also developed an express docking station that would reduce calibration time and labor costs. The detection and docking station help users meet record keeping requirements and reduce the risks of human error. With the SperianBiosystems PhD6 Multigas Detector, users can rest assured that they are receiving the very best in gas detection technology.

Key Features

The Biosystems PhD6 Multigas Detector is compatible with over 19 sensor choices including:

• PID
• IR-CO2
• IR-CH4
• Conventional LEL
• Oxygen
• 15 different toxic gas sensors

The gas detector is encased in a durable solid polycarbonate case with a rubber over mold for easy handling. It has an interchangeable battery pack with both Alkaline and Li-Ion rechargeable batteries. Both battery types offer up to 24 hour run times. The unit features dual audible alarms at 92 decibels and front and side ultra-bright LED visual alarms to ensure that the user and those nearby are always notified of possible hazardous conditions. For easy interpretation, the detector has an easy to read status bar and large LCD display that notifies users of the device s functionality and calibration due date. Using the menu options, users can easily adjust a variety of the instrument s settings.

Automatic Docking Station

When developing the PhD6 Multigas Detector, product developers also created an automatic docking station (Biosystems IQ6 Express Dock) to be fully compatible with the detector. The docking station aims to reduce labor time and costs by fully automating certain aspects of instrument maintenance including calibration, functionality testing, and record keeping. Using the Express Dock, users can maintain compliance with recordkeeping requirements by simply docking the detector in the station. The station will automatically perform a variety of operations without user intervention.

Sperian Protection Instrumentation and Honeywell

Sperian Protection Instrumentation is a global leader in personal safety equipment. The company was recently acquired by Honeywell, another global leader in technology and innovation. As a Fortune 100 company, Honeywell has a vested interest in maintaining its reputation as a developer of efficient and reliable safety equipment. Sperian Protection Instrumentation helps to expand Honeywell s personal safety offerings while advancing their position in the American market. By purchasing a product by Sperian and Honeywell, customers can be assured they are receiving the very best in safety technology and equipment.

MAB3-0EC1123-021 MultiRAE Lite Pumped Portable Multi-gas Monitor - O2 / LEL / H2S / CO / SO2 / Li-ion / Non-Wireless / Accessories Kit / Confined Space Kit (no gas or regulator) by RAE Systems

The MultiRAE Lite is the optimal one-to-six1-gas monitor for personal protection and leak detection applications. The MultiRAE Lite is available in pumped and diffusion versions and features the broadest selection of sensor options in its class. The MultiRAE Lite can be configured to exactly meet the detection needs and compliance requirements of various countries, industries, and applications.

The MultiRAE Lite's optional wireless capability improves safety by providing commanders and safety officers real-time access to instrument readings and alarm status from any location for better situational awareness and faster incident response.

Key Features

• Wireless access to real-time instrument readings and alarm status from any location
• Unmistakable five-way local and remote wireless notification of alarm conditions including Man Down Alarm
• Over 25 interchangeable sensor options, including PID for VOCs, NDIR and catalytic for combustibles, and NDIR for CO₂
• Intelligent sensors store calibration data, so they can be swapped in the field
• Large graphical display with easy-to-use, icon-driven user interface
• Continuous datalogging (6 months for 5 sensors, 24x7)

Applications

• Chemical
• Food and beverage
• Oil and gas (downstream)
• Pharmaceutical
• Telecommunications
• Wastewater treatment
• Fire overhaul

6170-1114 MGD-100 Gas Detection System, CH4: 0 - 5,000 ppm, 6 Sensors, 2 Alarms, Standard Housing, 110 VAC by Bacharach

Bacharach's MGD-100 Series is a robust and scalable gas detection system used for reliable real-time monitoring of refrigerant, combustible, and toxic gases. It's a stand-alone system that alarms when pre-set thresholds are exceeded. The MGD-100's alarms are monitored by a centralized controller, which can alert personnel of potential hazardous conditions via an onboard buzzer and LED alarm indicators.

MGD-100 Systems can be configured from single-sensor, one-alarm level systems to larger scale systems consisting of 6 sensors with 2 alarm levels. This flexibility allows the platform to be used for both small and large systems.

Ideal for Chiller Rooms, Supermarkets, Brewing and Bottling Facilities, Industrial Refrigeration, Arenas, Food Storage and Processing Facilities.

Features & Benefits:

• Stand-alone, out-of-the-box solution with quick and easy installation - the most cost-effective system available.
• Fast-response sensors detect leaks quickly, which minimize refrigerant gas usage and environmental impact.
• Infrared (NDIR) CO2 detection
• Long-life semiconductor sensors for detection of all refrigerants, ammonia, halocarbons, combustibles & VOCs
• Robust design allows units to be placed directly in areas where detection is needed.
• Available in a variety of housings, including IP66 and duct mount.
• Select from 1, 2, 4 or 6 remote sensors and 1 or 2 pre-set alarm levels, which can be connected to BMS systems.

G460-11-03-70-00-20 G460 Multi-Gas Detector With NiMH Battery, O2, Catalytic Combustion LEL Sensor, CO and H2S Sensor, PID (0.5-2000) by GfG

For over 50 years, GfG Instrumentation has worked to develop the most reliable and effective equipment for gas detection and measurement technology. Developed by a team of highly experienced scientists and specially trained engineers, GfG products are high quality reliable instruments designed to meet the unique needs of potentially hazardous worksite. With the introduction of the G460 Multi-Gas Detector, GfG Instrumentation is continuing the trend.

G460 Multi-Gas Detector

The G460 Multi-Gas Detector is a compact and robust system with the capabilities of detecting up to six different gases and simultaneously displaying the readings. The portable detector features a user friendly and intuitive interface to simplify the day to day operations.

Ease of Use

For typical daily operations, the G460 Multi-Gas Detector operates with a single button. The complete user interface can provide access to advanced setup options with three buttons. The unit also features easy calibration operation. Simply attach the calibration adapter and apply gas. The G460 will automatically perform the appropriate adjustments. The detector will then store the dates of the three most recent calibrations for each sensor.

The G460 also features a large easy to read tricolor display which uses a color code to indicate the alarm severity. From green to orange to red, the tricolor display is intuitive and incredibly user friendly. The display feature can also flip or zoom with the touch of a button. The G460 multi-faceted alarm system also includes an ultra loud audible buzzer at 103 dB, a standard vibration mechanism, and 360 bright LED alerts (the LED alerts can also be equipped to function as flashlights). This multi-faceted system is sure to alert users and those nearby of the potential hazardous conditions. For smooth and continuous operations, the G460 Multi-Gas Detector uses interchangeable alkaline and rechargeable battery packs that provide up to 25 hours of continuous operation. Using a drop in cradle charger, the rechargeable pack can completely recharge in less than 4 hours.

G460 Multi-Gas Detector Features

The G460 Multi-Gas Detector features a motorized pump with a built-in diffusion or sample draw mode switch. The hose is easily attachable and can draw from 100 feet away. The hose is powered by its own battery pack that provides 20 hours of continuous operation. The multi-gas detector also features the widest range of sensors on the market. The compatible long lasting (and interchangeable) smart sensors include LEL, SO2, O2, H2, H2S, NO, CO, O3, HF, NH3, CIO2, CI2, PH3, ETO, HCN, and NO2. Users can purchase additional sensors to help customize the unit such as infrared sensors for the measurement of CO2 and photoionization sensors for volatile organic chemical hazards. The G460 has standard data logging capabilities that store up to 55 hours of the most recent activities. Alarm activations gas thresholds and stored permanently in the internal memory. Employers can download all internal information to generate reports and monitor results.

01-29877 Peabody Gemini Round Dual Containment Tank, Blue, 160 Gallon 1.5 Specific Gravity by Quantrol

Features and Benefits of Gemini Tank System

• Specifically designed for the Water Treatment Industry
• Linear polyethylene construction. Polypropylene, XLPE and PVDF available - Superior chemical resistance for acids, caustics, sodium hypochlorite, biocides, etc. Handles aggressive applications that stainless steel and crosslink polyethylene will not.
• Heavy duty dual wall construction - Rated for liquids of 1.5 or 2.0 specific gravity. "Tank in a Tank" designed for instances where the primary tank fails; the chemical will then be safely contained in secondary tank.
• Integral pump mounting platform - Lid has 240 pound rating allowing for use with metering pump or mixer mounted directly to tank lid. Sump reservoir collects and drains pump spilled liquid back to primary.
• Pump pick-up tube port - Install pump suction line with check valve quickly and easily. Once installed, tank contents are sealed from outside environment.
• Integral mouse door - Molded directly into most Gemini models, recessed mouse door allows for inexpensive installation of optional bottom bulkhead fitting for flooded suction connection or bottom fill.
• Custom colors and mold-in graphics - Custom colors available, subject to minimum order quantity. Private label mold-in graphic is molded directly into tank and wont weather, crack, peel, or deteriorate.

Sperian Biosystems PhD6 Multigas Detector

The Biosystems PhD6 Multigas Detector is the latest development in compact multigas detection systems. The detector is proven to be compact, efficient, and cost effective. With dual alarm systems featuring ultra-loud audible indicators and ultra-bright LED visual indicators, users and those nearby are always notified when potential hazards may be present. When developing this detector, the engineers at SperianProtection Instrumentation also developed an express docking station that would reduce calibration time and labor costs. The detection and docking station help users meet record keeping requirements and reduce the risks of human error. With the SperianBiosystems PhD6 Multigas Detector, users can rest assured that they are receiving the very best in gas detection technology.

Key Features

The Biosystems PhD6 Multigas Detector is compatible with over 19 sensor choices including:

• PID
• IR-CO2
• IR-CH4
• Conventional LEL
• Oxygen
• 15 different toxic gas sensors

The gas detector is encased in a durable solid polycarbonate case with a rubber over mold for easy handling. It has an interchangeable battery pack with both Alkaline and Li-Ion rechargeable batteries. Both battery types offer up to 24 hour run times. The unit features dual audible alarms at 92 decibels and front and side ultra-bright LED visual alarms to ensure that the user and those nearby are always notified of possible hazardous conditions. For easy interpretation, the detector has an easy to read status bar and large LCD display that notifies users of the device s functionality and calibration due date. Using the menu options, users can easily adjust a variety of the instrument s settings.

Automatic Docking Station

When developing the PhD6 Multigas Detector, product developers also created an automatic docking station (Biosystems IQ6 Express Dock) to be fully compatible with the detector. The docking station aims to reduce labor time and costs by fully automating certain aspects of instrument maintenance including calibration, functionality testing, and record keeping. Using the Express Dock, users can maintain compliance with recordkeeping requirements by simply docking the detector in the station. The station will automatically perform a variety of operations without user intervention.

Sperian Protection Instrumentation and Honeywell

Sperian Protection Instrumentation is a global leader in personal safety equipment. The company was recently acquired by Honeywell, another global leader in technology and innovation. As a Fortune 100 company, Honeywell has a vested interest in maintaining its reputation as a developer of efficient and reliable safety equipment. Sperian Protection Instrumentation helps to expand Honeywell s personal safety offerings while advancing their position in the American market. By purchasing a product by Sperian and Honeywell, customers can be assured they are receiving the very best in safety technology and equipment.

0563 3000 72 330i Kit #3 - O2 & CO (with Bluetooth & Dilution) Upgrade Kit (No display - Download Free App) by Testo

Kit Includes:

• 330i Combustion Analyzer w/ Bluetooth (BT) & auto CO dilution (No display - Download Free App*)
• 0554 1096 - Power supply / recharger (North American cord)
• 0516 3302 - Carrying case
• 0554 3385 - Spare particle filter, 10 pack