$100 - $150

90551-35 Sil-Filled Bottom-Con Bimetal Thermometer, 3" Dial, 9" L/0-250F/-20-120C by Digi-Sense

Accuracy is ±1% full-scale when stem is immersed 2" in liquids or 4" in gases (immerse models with a 2.5" stem length 2" in gases). Measured stem length from the top of the threads to the bottom tip of the stem. Stem dia is 0.25"; threaded connection is 1/2" NPT(M). All thermometers meet or exceed ASME B40.3 standards. Maximum environmental temperature for Acrylic lens thermometers is 200°F (93°C).

• Dampened movement
• Anti-parallax dial for accurate readings
• Hermetically sealed per ASME B40.3 standard to prevent fogging and protect against tough environments
• Rugged 304 stainless steel construction with Acrylic lens
• Recalibrate using the external reset screw
• For use in applications that do not exceeding 200F

90551-36 Sil-Filled Bottom-Con Bimetal Thermometer, 3" Dial, 9" L/50-300F/10-150C by Digi-Sense

Accuracy is ±1% full-scale when stem is immersed 2" in liquids or 4" in gases (immerse models with a 2.5" stem length 2" in gases). Measured stem length from the top of the threads to the bottom tip of the stem. Stem dia is 0.25"; threaded connection is 1/2" NPT(M). All thermometers meet or exceed ASME B40.3 standards. Maximum environmental temperature for Acrylic lens thermometers is 200°F (93°C).

• Dampened movement
• Anti-parallax dial for accurate readings
• Hermetically sealed per ASME B40.3 standard to prevent fogging and protect against tough environments
• Rugged 304 stainless steel construction with Acrylic lens
• Recalibrate using the external reset screw
• For use in applications that do not exceeding 200F

H-10-112-20 Xylene Colorimetric Gas Detection Tube, 10 - 200 ppmv (10 Tubes / Box) by RAE Systems

RAE Systems colorimetric gas detection tubes enable quick, on-the-spot measurement of a wide range of toxic and combustible gases and vapors. RAE Systems tubes are easy to read, and provide a sharp, clear color change directly corresponding to the concentration of gas present. RAE Systems tubes are compatible with the RAE Systems piston hand pump, a reliable way to draw samples of an exact volume required for the most accurate measurements.

Key Features

• Wide assortment of tubes available to detect over 300 gases and vapors
• Easyto use, even in multiple layers of gloves
• Easy-to-read with sharp,clearcolorchange
• No calibration or other maintenance required

Applications

• Oil and gas
• Chemicals and petrochemicals
• Agriculture and pestcontro
• Food and beverage production
• Environmental protection
• Fire service
• HazMat response
• Nationalsecurity

Part Number: 34L-176P-500

275 Clamp-On Tester with True RMS Digital Multimeter and 11,000 Count Display by Test Products International

Clamp-On Tester with True RMS Digital Multimeter & 11,000 Count Display. The new TPI 275 with slim jaw and body is ideal for cramped work areas and crowded electrical panels.

The slim design 275 is a hand-held, autoranging clamp-on DMM. Extra large numerals, min/max, capacitance, DC microamps and duty cycle are just a few of the features of the 275. An affordable choice, the 275 offers measurements in all basic electrical functions with additional advanced features like non-contact voltage.

Features:

• True RMS
• 11,000 count display
• Up to 400 amps AC/DC
• Auto & Manual Ranging
• Data Hold
• Low Battery Indicator
• Over Range Indication ("OL")
• Peak Hold
• Min/Max
• Relative Mode
• Hi Voltage Indicator(>30V AC/DC)
• Non-contact voltage detection
• Auto Power Off after 30 minutes
• Separate Battery Compartment
• Low Ohm Range (110Ω)
• Amps AC Resolution: 0.01A
• VDC/VAC Resolution: 0.01mV
• DCiA measurement (0.01μA resolution)
• Temperature measurement

Applications:

• Measure DC amperage of motor drive units
• Measure flame safety control current
• Test run and start capacitors and motors
• Measure motor run current and capture peak motor start up amperage
• Measure heat anticipator current
• Determine thermocouple voltage
• Test line and control voltages
• Measure heating element resistance
• Measure air temperature in ducts
• Test for the presence of voltage in circuits without contacting the circuit
• Measure temperature differential using relative mode

The 275 comes complete with the following accessories:

• Carrying Pouch
• Test Lead Set
• Temperature Probe
• Instruction Manual
• Battery & Fuse

*Please note we can only ship RKI products to customers within the United States

Part Number: 34L-374

90446-82 Industrial Temperature Probe, Type J, 9" L, 1/4" Dia, Ungrounded, 316 Stainless Steel/Aluminum by Digi-Sense

These MgO thermocouple assemblies consist of a single or dual thermocouple element constructed of various sheath materials, assembled together with a connection head.

Features

• Inconel, 316 Stainless steel or 304 Stainless steel sheath materials
• 1/2" X 1/2" NPT stainless steel hex nipple for head mounting fittings
• Aluminum screw cover, Cast iron screw cover, or Cast iron/aluminum explosion proof class C Heads
• Standard Limits of Error
• Grounded Measuring Junction
• Custom built assemblies available upon request

*Please note we can only ship RKI products to customers within the United States

720CK Pocket Thermometer with Four Interchangeable Stainless Steel Probes Kit by Jenco

Pocket Thermometer with four interchangeable stainless steel probes for immersion, penetration, surface or air/gases measurements. Sold in kits with all four probes and a handy padded vinyl pouch. Optional 2 meter extended curly cord model 720-31 is available for use when probes and meter are used for remote sensing.

Includes:

• 720C Pocket Thermometer
• 720-01: Immersion Probe
• 720-02: Penetration Probe
• 720-03: Air & Gases Probe
• 720-04: Surface Probe
• 720-99: Vinyl Pouch

• °C and °F models
• Splash resistant case
• Battery life : ~150 hrs.

Part Number: 34L-361

WD-17105-00 InnoCal NIST-Traceable Calibration; Refractometer by Oakton

Calibration reports issued by InnoCal may not be reproduced, except in full, without written permission of InnoCal. The results stated in our reports relate only to the items tested or calibrated. Measurements reported on our reports are traceable to SI units via national standards maintained by NIST and are performed in compliance with MIL-STD-45662A, ANSI/NCSL Z540-1-1994, 10CFR50, Appendix B, ISO9002-94, and ISO/IEC 17025:2005