Bacharach

0024-0788 Oxygen Sensor, 2-year by Bacharach

The O2 sensor is used in Bacharach portable combustion analyzers to measure the percentage content of oxygen levels in flue gases. The range of the oxygen sensor is 0 – 20.9%. O2 measurement is used in conjunction with the chosen fuel to calculate the CO2 levels in flue gases. Bacharach portable combustion analyzers only calculate CO2 when oxygen levels are below 16%. Bacharach uses O2 and other readings in determining efficiency rather than CO2 for a more accurate measurement. Measuring oxygen content in the excess air lets you know if you have too much air or too much fuel, allowing you to tune your furnace or boiler to maximum efficiency. Measuring O2 directly can save fuel, and save time during a combustion tune-up test.

• Measures percentage content of oxygen levels in flue gas
• Provides more accurate efficiency readings
• Saves time during tune-ups, telling you if air or fuel is too high
• Available in two year, three year, and five year sensor life depending on instrument

5201-1031 GDC-150 Gas Sensor Transmitter, NEMA 1 Housing, MOS Refrigerant Sensor by Bacharach

The all new GDC-150 transmitter from Bacharach offers detection and protection for a wide range of hazards including toxic gases such as carbon monoxide (CO), oxygen depletion, combustible gases, refrigerant leaks and total volatile organic compounds (TVOCs). Analog interfaces allow the transmitter to be connected back to Bacharach's GDA Series of controllers (or any other gas detection controller), building management systems or control systems. The GDC-150 features 4-20 mA or 0-10 VDC linear output signals, an automatic thermal resetting fuse, RoHS compliant circuit boards and LED indicators for power and open loop.

The onboard alarm LED's indicate when alarm threshold values are exceeded. The unit can be ordered with an optional alpha numeric LED display that shows gas concentrations in real time while alarm relays alert personnel of potential dangers, avoiding incidents and potential hazards.

The GDC-150 is packaged in a rugged, polycarbonate housing for both indoor and outdoor applications. When leaks occur, the GDC-150 sensors respond quickly and accurately to protect people and property. Automated calibration and simple maintenance procedures performed in the field allow for continuous operation and assurance that areas are monitored and protected at all times.

0024-8400 ECA 450 NOx kit, includes O2, CO/H2-compensated (0-4,000 ppm), NO, NO2 and compact sample conditioner with 12 in. sample probe and 15 ft. sample line/hose assembly by Bacharach

MSA Bacharach's ECA 450 is an industrial grade analyzer ideal for professionals concerned about combustion efficiency, environmental compliance, or both. Accommodating up to seven sensors, simultaneous measurements and calculated parameters are evaluated to ensure that industrial equipment is meeting environmental regulations while burning safely and efficiently.

The ECA 450 is designed for on-demand or semi-continuous sampling of industrial furnaces, boilers and other industrial combustion equipment. It complies with regulations such as U.S. EPA test methods, EN 50379, CTM-030 and state/local protocols including SCAQMD.

Note: The ECA 450 calculates CO2 value based upon other measured values during the combustion process. It does not measure CO2 directly.

Features

• Measures up to 7 gases simultaneously (minimum O2 and CO), including NOx, SOx and combustibles
• Sensors are easily replaced or upgraded in the field
• Rugged suitcase design with large, easy-to-read display
• Built-in printer for instant traceability and record-keeping

0028-8013 Tru Pointe 2100 kit with noise-attenuating headphones & SoundBlaster ultrasonic sound generator by Bacharach

The MSA Bacharach Tru Pointe® series products are advanced digital ultrasonic inspection systems used by maintenance personnel for mechanical inspections, troubleshooting and PPM (preventative and predictive maintainence) or scheduled maintenance in a variety of industries and ideal for tanks,enclosures, building doors & windows, automobile windows & windshields, walk-in coolers, clean rooms ship hatches and compartments.

The principle of operation of the Tru Pointe® series product line is based on the detection of ultrasonic acoustics generated by leaks produced by the turbulent flow of gases and liquids, inaudible to humans, and pinpoints them at the speed of sound. Carrying multiple patents, the Tru Pointe® Series incorporates independent sensors that identify external airborne leaks and internal structural leaks. Such as leaks in steam traps, valves, solenoids, pumps and hydraulics, compressed air, refrigerants, nitrogen, CO2, helium, vacuum and many others sources for accurate, repeatable results, saving time and money for every HVAC/R technician and contractor.

Features

• Ultrasonic to detect any gas leaks
• Sensitivity Adjustments
• Visual indication
• Unique Volume control
• Pocket Sized
• Dual Audio Intensity Displays

Benefits

• Capable of detecting a 5 PSI leak out of a 0.005" hole, 30 to 40 feet away. Ideal for stream trap testing and bearing wear detection. Unaffected by wind or temperature fluctuations. Find a leak as small as 2.5-3 oz./yr (84 g/yr)
• Unaffected by other gases, even at high-concentrations or sounds in the test area.
• Ten-step LED Bar Graphs shows signal strength.
• True sound reproduction ensures fast recognition of leaks.
• Easy to carry
• Easily see bar graph or alpha/numeric displays

6401-0518 MGS-250 Infrared R449A Detector by Bacharach

Bacharach's new MGS-250 Infrared Refrigerant Gas Transmitter is the leader in performance and flexibility at an economical price. There are two versions available - a cost-effective broadband sensor used for gross leak detection or gas-particular versions that are even more distinct, pre-calibrated and characterized for response to specific refrigerants. Its simple-to-use interface gives the user the ability to set all parameters and outputs without opening the unit, moving jumpers, using mulitmeters or adjusting potentiometers.

The MGS-250 family is a cost effective solution for detecting a variety of refrigerants without the limitations posed by solid-state sensor technologies. The long-life, proprietary NDIR infrared sensor allows for accurate low-level leak detection (0-3,500 ppm), delivering up to 5-7 years of maintenance-free operation without the need for costly annual gas calibrations. Infrared sensing technology makes the MGS-250 immune to cross sensitivities to combustible and toxic gas as well as changes in temperature and humidity. The unit has an alpha-numeric LED display to show constant real-time readings, an on-board LED indicator for when the sensor is in an alarm state, and an audible alarm to alert personnel in the area that levels have exceeded the desired limit. An optional protective splash guard is available for use in areas with high water spray such as food and beverage facilities or chiller rooms.

Features & Benefits:

• Long-life, Non-Dispersive Infrared (NDIR) sensor allows for accurate low-level leak detection
• Detects all refrigerants (CFC, HFCs, HCFC, HFO's), including HFO1234YF, HFO1234ZE, R410a & R22
• Fast-responding, refrigerant-specific sensor with no cross interferences to other gases
• No field calibrations required
• Modbus RTU interface to connect to BAS/BMS systems and on-board alarm relay
• User selectable analog output: 4-20 mA, 0-5V, 1-5V, 0-10V, 2-10V
• Bright, alpha-numeric LED real-time display with on-board audible and visual alarms

6302-2053 MGS-450 Gas Detector - IP66, 3 x Relays, Analog Output, Modbus Output, Audible & Visual Alarms - CH4, 0-100% LEL, Infrared by Bacharach

Bacharach's MGS-400 Gas Detectors makes compliance with mechanical equipment room and refrigeration safety codes simple and easy, saving time and money on equipment and installation. Using the MGS-400 App, users can intuitively use, commission and maintain their gas detection system without the need for specialty training or tools. Pre-calibrated sensor modules simplify maintenance, take minutes to exchange and do not require the use of calibration gas. The MGS-400 sensors can trigger additional audio-visual alarms and act as a standalone gas detection system, or integrate easily into a BMS / BAS or with Bacharach's optional MGS-408 Gas Detection Controller.

Features

• Mobile App Interface
• Pre-calibrated Sensors
• Semi-automated Calibration
• Remote Sensor Option
• Temperature-Compensated Measurement
• Low Temperature Performance
• Digital Communications
• Analog Outputs
• Relay outputs
• Audio & Visual Alarms
• Multiple Cable Entries and Terminals

Benefits

• Quick, easy and intuitive commissioning, configuration and maintenance requires no special training. No tools required to set alarm levels and behavior
• Fast and easy sensor maintenance. Eliminates need for calibration gas.
• Easy calibration process with mobile app. Generate calibration certificates for documentation.
• Locate the sensor element in hard-to-reach areas and the base unit where convenient for electrical and communication wiring (MGS-460)
• Mitigates false alarms and optimizes accuracy in refrigeration applications.
• Suitable for use in cold rooms and freezers down to -40° F/C.
• Integrate with local BMS/BAS via Modbus RTU
• For current or voltage output to legacy systems (MGS-450/460)
• 3 relays available for alarm and fault events to active horn/strobes and ventilation (MGS-450, MGS-460)
• On-board alarm notification supports compliance with ASHRAE 15 / EN 378
• Quick and easy installation of all wiring; daisy-chain power and digital communications.

0019-7075 Leakator Jr Combustible Gas Leak Detector with 4x AA batteries, soft carrying case and instruction manual by Bacharach

The MSA Bacharach Leakator® Jr. is an economical handheld combustible gas leak detector used to pinpoint leaks in commercial, residential and industrial applications including surveying gas pipelines and inspecting valves, regulators and meters on gas equipment. With two sensitivity modes the Leakator® Jr. detects acetone, acetylene, benzene, butane, ethanol, ethylene oxide, gasoline, hexane, hydrogen, industrial solvents, isobutane, methane, methanol, naphtha, natural gas, paint thinners and propane.

Dependable Operation

The compact design of the Leakator® Jr. is equipped with a flexible 12 inch probe for pinpointing the location of combustible gas leaks in any hard-to-reach area. The one button operation Leakator® Jr. is a reliable lightweight instrument with an automatic self-check each time the instrument is turned on. Combustible gas leaks are indicated by a simple variable frequency visual LED and loud audible tick rate that increases as the sensor approaches a leak.

Features

• Compact and ergonomic design plus simple one button operation
• Automatic self-check
• Relative concentration of the gas present is indicated by the frequency of audible and visual alarms
• High and low sensitivity mode selectable by a double press of the On/Off button
• Low power plug-in sensor

Benefits

• Allows the user to hold and operate the instrument in one hand
• Occurs during warm-up when instrument is turned on in fresh air
• Audible and visual alarms
• Pinpoints concentrations as small as 20 ppm in the high-sensitivity mode
• Quick sensor replacement

0010-5021 Fyrite CO2 (0-20%) and O2 (0-21%) testing kit, sampling assembly and carry case (NO FLUID - FOR EXPORT) by Bacharach

Bacharach® Combustion Testing Kits continue to offer you the most economical means of testing for oil burner efficiency during installation or servicing. Each kit is designed with the service technician in mind and contains the instruments listed in the ordering chart.

Components

• 1. Fyrite® Indicators; CO2 and O2 – The Fyrite Indicators are utilized in conjunction with the Tempoint Dial thermometer to determine efficiency calculation with the Fire Efficiency Slide Rule.
• 2. Monoxor® CO Indicator – The Monoxor Indicator quickly and easily tests CO concentrations in flue gas samples.
• 3. Fire Efficiency Finder/Stack Loss Slide Rule – The Fire Efficiency Slide Rule provides a rapid and uncomplicated means of determining combustion efficiency and stack loss from the resultsof the CO2 and stack temperature tests.
• 4. Draftrite® Draft Gauge – The hand-held Draftrite pinpoints draft problems and determines chimney defects.
• 5. Tempoint® Dial Thermometer – With the Tempoint Dial Thermometer, you can obtain an accurate stack temperature of gas designed equipment.
• 6. Gas Service Calculator – The Gas Service Calculator determines the orifice size needed for fuel gas of any specific gravity and BTU value.
• 7. Gas Pressure Manometer – The Gas Pressure Manometer determines if gas input and gas pressure adjustments are within recommended limits.
• 8. Monoxor® Carbon Monoxide Detector – In some Testing Kits, the Monoxor Carbon Monoxide Detector replaces the Monoxor CO Indicator.
• 9. Carrying Case – Testing kit comes in a rugged, plastic carrying case.